Investigating the effect of electrospark alloying parameters on structure formation of modified nitrogen coatings

• Autorzy: Haponova Oksana , Tarelnyk Viacheslav , Mościcki Tomasz , Tarelnyk Nataliia

Identyfikatory

DOI

10.24425/bpasts.2024.150802

• Języki publikacji: EN

Abstrakty

EN

The quality parameters of surface layers synthesised using electrospark alloying (ESA) technology were analysed in this paper. The main focus was on the influence of equipment energy parameters on structure formation, specifically the effect of discharge energy and productivity. Microstructural analysis of the modified surface of C40 steel after nitriding by ESA using a paste containing nitrogen compounds injected into the interelectrode gap was conducted. The layer structure for all studied ESA parameters includes three areas: the upper “white layer”, the diffusion zone below it, and the substrate. The roughness of the surface is Ra ∼ 0.9 µm at low discharge energy Wp = 0.13 J and Ra ∼ 6 µm at Wp = 3.4 J. The microhardness, continuity, and surface roughness of the layers varied with Wp. The influence of ESA productivity on the structure was studied. The thickness of the hardened layer and the diffusion zone, as well as the microhardness and continuity, are affected by reduced productivity. For the same discharge energy, the thickness of the hardened layer increases by 10-18% with a decrease in productivity compared to the classical mode. Studies have shown that productivity loss has a positive effect on the quality characteristics of the coatings produced by the ESA process.

Słowa kluczowe

EN

electrospark alloying; discharge energy; productivity; coating; structure

PL

stopowanie elektroiskrowe; energia wyładowania; produktywność; powłoka; struktura

• Wydawca: Polska Akademia Nauk, Wydział IV Nauk Technicznych
• Czasopismo: Bulletin of the Polish Academy of Sciences. Technical Sciences
• Rocznik: 2024
• Tom: Vol. 72, nr 5
• Strony: art. no. e150802
• Opis fizyczny: Bibliogr. 31 poz., rys., tab.

Twórcy

autor

Haponova Oksana

• Department of Experimental Mechanics, Institute of Fundamental Technological Research Polish Academy of Sciences,Pawinskiego 5B, 02-106 Warsaw, Poland
• Applied Material Science and Technology of Constructional Materials Department, Sumy State University, Kharkivska 116, 40007 Sumy, Ukraine

• https://orcid.org/0000-0002-4866-0599

autor

Tarelnyk Viacheslav

• Technical Service Department, Sumy National Agrarian University, H. Kondratiieva 160, 40021 Sumy, Ukraine

• https://orcid.org/0000-0003-2005-5861

autor

Mościcki Tomasz

• Department of Experimental Mechanics, Institute of Fundamental Technological Research Polish Academy of Sciences,Pawinskiego 5B, 02-106 Warsaw, Poland

• https://orcid.org/0000-0002-8407-903X

autor

Tarelnyk Nataliia

• Technical Service Department, Sumy National Agrarian University, H. Kondratiieva 160, 40021 Sumy, Ukraine

• https://orcid.org/0000-0002-6304-6925

Bibliografia

• [1] S. Shevchenko, O. Shevchenko, and S. Vynnychuk, “Mathematical Modelling of Dynamic System Rotor-Groove Seals for the Purposes of Increasing the Vibration Reliability of NPP Pumps,” Nucl. Radiat. Saf., vol. 1, no. 89, pp. 80–87, 2021, doi: 10.32918/nrs.2021.1(89).09.
• [2] S. Shevchenko and O. Shevchenko, “Improvement of Reliability and Ecological Safety of NPP Reactor Coolant Pump Seals,” Nucl. Radiat. Saf., vol. 4, no. 88, pp. 47–55, 2020, doi: 10.32918/nrs.2020.4(88).06.
• [3] M. Stechyshyn, O. Dykha, and V. Oleksandrenko, “Nitriding of long-term holes in the cyclic-commuted discharge,” J. Eng. Sci., vol. 10, no. 2, pp. C11–C18, 2023, doi: 10.21272/jes.2023.10(2).c2.
• [4] B. Antoszewski, S. Tofil, M. Scendo, and W. Tarelnik, “Utilization of the UV laser with picosecond pulses for the formation of surface microstructures on elastomeric plastics,” in IOP Conf. Ser.-Mater. Sci. Eng., vol. 233, p. 012036, 2017, doi: 10.1088/1757-899X/233/1/012036.
• [5] I.P. Shatskyi, V.V. Perepichka, and L.Ya. Ropyak, “On the Influence of Facing on Strength of Solids with Surface Defects,” Metallofiz. Noveishie Tekhnol., vol. 42, no. 1, pp. 69–76, 2020, doi: 10.15407/mfint.42.01.0069.
• [6] M.S. Storozhenko, A.P. Umanskii, A.E. Terentiev, and I.M. Zakiev, “Effect of the Structure of TiB2–(Fe–Mo) Plasma Coatings on Mechanical and Tribotechnical Properties,” Powder Metall. Met. Ceram., vol. 56, no. 1–2, pp. 60–69, 2017, doi: 10.1007/s11106-017-9847-y.
• [7] M.S. Storozhenko, “Effect of Molybdenum Additions on the Structurization of Fe–Mo Alloys and Contact Interaction in the TiB2–(Fe–Mo) Systems,” Powder Metall. Met. Ceram., vol. 55, pp. 617–624, 2017, doi: 10.1007/s11106-017-9847-y.
• [8] M. Bembenek, P. Prysyazhnyuk, T. Shihab, R. Machnik, O. Ivanov, and L. Ropyak, “Microstructure and Wear Characterization of the Fe-Mo-B-C–Based Hardfacing Alloys Deposited by Flux-Cored Arc Welding,” Materials, vol. 15, no. 14, p. 5074, 2022, doi: 10.3390/ma15145074.
• [9] B.O. Trembach et al., “Effect of Incomplete Replacement of Cr for Cu in the Deposited Alloy of Fe–C–Cr–B–Ti Alloying System with a Medium Boron Content (0.5% wt.) on its Corrosion Resistance,” Metallofiz. Noveishie Tekhnol., vol. 44, no. 4, pp. 493–513, 2022, doi: 10.15407/mfint.44.04.0493.
• [10] L. Ropyak, I. Schuliar, and O. Bohachenko, “Influence of technological parameters of centrifugal reinforcement upon quality indicators of parts,” East. Eur. J. Enterp. Technol., vol. 1, no. 5, đp. 53–62, 2016, doi: 10.15587/1729-4061.2016.59850.
• [11] O. Bazaluk, O. Dubei, L. Ropyak, M. Shovkoplias, T. Pryhorovska, and V. Lozynskyi, “Strategy of Compatible Use of Jet and Plunger Pump with Chrome Parts in Oil Well,” Energies, vol. 15, no. 1, p. 83, 2022, doi: 10.3390/en15010083.
• [12] S. Pylypaka, T. Volina, A. Nesvidomin, I. Zakharova, and A. Rebrłi, “Particle Movement in a Centrifugal Device with Vertical Blades,” in DSMIE 2021 Advances in Design, Simulation and Manufacturing IV. Lecture Notes in Mechanical Engineering, 2021, pp. 156–165, doi: 10.1007/978-3-030-77823-1_16.
• [13] S. Pylypaka, V. Nesvidomin, T. Volina, L. Sirykh., and L. Ivashyna, “Movement of the Particle on the Internal Surface of the Spherical Segment Rotating About a Vertical Axis,” INMATEH–Agric. Eng., vol. 62, no. 3, pp. 79–86, 2020, doi: 10.35633/inmateh-62-08.
• [14] S. Pylypaka, T. Volina, M. Mukvich, G. Efremova, and O. Kozlova, “Gravitational Relief with Spiral Gutters, Formed by the Screw Movement of the Sinusoid,” in DSMIE 2020. Advances in Design, Simulation and Manufacturing III. Lecture Notes in Mechanical Engineering, 2020, pp. 63–73, doi: 10.1007/978-3-030-50491-5_7.
• [15] V. Tarelnyk, O. Gaponova, Ye. Konoplianchenko, V. Martsynkovskyy, N. Tarelnyk, and O. Vasylenko, ”Improvement of Quality of the Surface Electroerosive Alloyed Layers by the Combined Coatings and the Surface Plastic Deformation. II. The Analysis of a Stressedly-Deformed State of Surface Layer after a Surface Plastic Deformation of Electroerosive Coatings,” Metallofiz. Noveishie Tekhnol., vol. 41, no. 2, 173, 2019, doi: 10.15407/mfint.41.02.0173.
• [16] T. Volina, S. Pylypaka, A. Rebrii, O. Pavlenko and Ya Kremets, “Particle Movement on Concave Coulter of the Centrifugal Distributor with Radially Installed Vertical Blades,” in InterPartner 2020. Advanced Manufacturing Processes II. Lecture Notes in Mechanical Engineering, 2021, pp. 237–246, doi: 10.1007/978-3-030-68014-5_24.
• [17] A.D. Pogrebnjak et al., “Positron annihilation studies of defect structure of (TiZrHfNbV)N nitride coatings under Xe14+200 MeV ion irradiation,” Mater. Lett., vol. 303, p. 130548, 2021, doi: 10.1016/j.matlet.2021.130548.
• [18] V.F. Gorban, A.O. Andreev, V.A. Stolbovoi, A.M. Myslyvchenko and A.D. Kostenko, “Properties of Metal–Metal Nitride Vacuum-Arc Multilayer Coatings”, J. Superhard Mater., vol. 42, no. 1, đp. 25–29, 2020, doi: 10.3103/S1063457620010050.
• [19] V.B. Tarelnyk et al., “Improving Ecological Safety when Forming Wear-Resistant Coatings on the Surfaces of Rotation Body Parts of 12Kh18N10T Steel Using a Combined Technology Based on Electrospark Alloying”, Surf. Engin. Appl. Electrochem., no. 57, pp. 173–184, 2021, doi: 10.3103/S1068375521020113.
• [20] B. Antoszewski et al., “Assessment of Technological Capabilities for Forming Al-C-B System Coatings on Steel Surfaces by Electrospark Alloying Method,” Materials, no. 14, p. 739, 2021, doi: 10.3390/ma14040739.
• [21] J. Wang, M. Zhang, S. Dai, and L. Zhu, “Research Progress in Electrospark Deposition Coatings on Titanium Alloy Surfaces: A Short Review”, Coatings, vol. 13, no. 8, p. 1473, 2023, doi: 10.3390/coatings13081473.
• [22] V. Mihailov et al., “Synthesis of Multicomponent Coatings by Electrospark Alloying with Powder Materials”, Coatings, vol. 13, p. 651, 2023, doi: 10.3390/coatings13030651.
• [23] A.V. Ribalko and O. Sahin, “A Modern Representation of the Behaviour of Electrospark Alloying of Steel by Hard Alloy,” Surf. Coat. Technol., vol. 201, no. 3–4, pp. 1724–1730, 2006, doi: 10.1016/j.surfcoat.2006.02.044.
• [24] O. Gaponova et al., “Estimating Qualitative Parameters of Aluminized Coating Obtained by Electric Spark Alloying Method”, in Advances in Thin Films, Nanostructured Materials, and Coatings. Lecture Notes in Mechanical Engineering, A.D. Pogrebnjak, V. Novosad, Eds. Springer, Singapore, 2019, pp. 249–266, doi: 10.1007/978-981-13-6133-3_25.
• [25] V.B. Tarelnyk, O.P. Gaponova, G.V. Kirik, Ye.V. Konoplianchenko, N.V. Tarelnyk, and M.O. Mikulina, “Cementation of Steel Details by Electrospark Alloying,” Metallofiz. Noveishie Tekhnol., vol. 42, no. 5, pp. 655–667, 2020, doi: 10.15407/mfint.42.05.0655.
• [26] O.P. Gaponova et al., “Technological Features for Controlling Steel Part Quality Parameters by the Method of Electrospark Alloying Using Carburezer Containing Nitrogen-Carbon Components,” Materials, no. 15, p. 6085, 2022, doi: 10.3390/ma15176085.
• [27] O.P. Gaponova, B. Antoszewski, V.B Tarelnyk, P. Kurp, O.M. Myslyvchenko, and N.V. Tarelnyk, “Analysis of the Quality of Sulfomolybdenum Coatings Obtained by Electrospark Alloying Methods,” Materials, no. 14, p. 6332, 2021, doi: 10.3390/ma14216332.
• [28] V.B. Tarelnyk, A.V. Paustovskii, Yu.G. Tkachenko, E.V. Konoplianchenko, V.S. Martsynkovskyi, and B. Antoszewski “Electrode materials for composite and multilayer electrospark-deposited coatings from Ni–Cr and WC–Co alloys and metals,” Powder Metall. Met. Ceram., vol. 55, no. 9–10, p. 585, 2017, doi: 10.1007/s11106-017-9843-2.
• [29] C. Barile, C. Casavola, G. Pappalettera, and G. Renna, “Advancements in Electrospark Deposition (ESD) Technique: A Short Review,” Coatings, vol. 12, p. 1536, 2022, doi: 10.3390/coatings12101536.
• [30] V. Martsynkovskyy, V. Tarelnyk, I. Konoplianchenko, O. Gaponova, and M. Dumanchuk, “Technology Support for Protecting Contacting Surfaces of Half-Coupling-Shaft Press Joints Against Fretting Wear ,” in DSMIE 2019. Advances in Design, Simulation and Manufacturing II. Lecture Notes in Mechanical Engineering, 2020, pp. 216–225, doi: I10.1007/978-3-030-22365-6_22.
• [31] O.P. Haponova et al., “Improvement of Quality Parameters of Surface Layers of Steel Parts after Aluminizing by Electrospark Alloying. Pt. 1. Features of the Structural State of Steel Surfaces after Aluminizing ,” Metallofiz. Noveishie Tekhnol., vol. 45, no.12, p. 1449, 2023, doi: 10.15407/mfint.45.12.1449.