Measurement of the friction parameters of a belt transmission under heavy load

• Autorzy: Kubas Krzysztof

Identyfikatory

DOI

10.14669/AM.VOL95.ART2

• Języki publikacji: EN

Abstrakty

EN

This article presents the results of measurements of a belt transmission with a poly-V belt 5PK, most often used in the industry, especially in industrial drives, agricultural machines and in the automotive industry. The main goal of the works was to obtain the dependence of the belt slip value on the measured, relatively high values of resistance torque. For this purpose, a series of measurements were made using a specialised research stand consisting of two alternating current motors and attached pulleys. It considered four cases of the value of the belt pre-tensioning force. In each of the cases, while making the measurements, the resistance of the passive pulley was increased, resulting in increasing values of belt slip. Finally, the achieved courses were approximated. The obtained results will be used to develop empirical models of friction at the belt-pulley interface. They can also be useful for belt manufacturers to make better belts, especially those subjected to higher loads.

Słowa kluczowe

EN

poly-V belt; belt transmission; belt slip; measurements; belt-pulley friction

• Wydawca: Wydawnictwo Naukowe Sieci Badawczej Łukasiewicz - Przemysłowego Instytutu Motoryzacji
• Czasopismo: Archiwum Motoryzacji
• Rocznik: 2022
• Tom: Vol. 95, nr 1
• Strony: 18--31
• Opis fizyczny: Bibliogr. 32 poz., rys.

Twórcy

autor

Kubas Krzysztof

• Department of Combustion Engines and Vehicles, University of Bielsko-Biała, Willowa 2, 43-309 Bielsko-Biała, Poland

• https://orcid.org/0000-0002-3594-8665

Bibliografia

• [1] Balta B., Sonmez F.O., Cengiz A.: Speed losses in V-ribbed belt drives. Mechanism and Ma-chine Theory. 2015, 86, 1–14, DOI: 10.1016/j.mechmachtheory.2014.11.016.
• [2] Balta B., Sonmez F.O., Cengiz A.: Experimental identification of the torque losses in V-ribbed belt drives using the response surface method. Proceedings of the Institution of Mechanical Engineers. Part D: Journal of Automobile Engineering. 2015, 229(8), 1070–1082, DOI: 10.1177/0954407014555150.
• [3] Belyaev A.K., Eliseev V.V., Irschik H., Oborin E.A.: Contact of two equal rigid pulleys with a belt modelled as Cosserat nonlinear elastic rod. Acta Mechanica. 2017, 228(12), 4425–4434, DOI: 10.1007/s00707-017-1942-0.
• [4] Belyaev A.K., Eliseev V.V., Irschik H., Oborin E.A.: Dynamics of contour motion of belt drive by means of nonlinear rod approach. Dynamics and Control of Advanced Structures and Machines. 2019, 3, 21–29, DOI: 10.1007/978-3-319-90884-7_3.
• [5] Bucchi F., Frendo F.: Analysis of belt transmissions capabilities using the brush model. Institute of Physics Conference Series: Materials Science and Engineering. 2021, 1038(1), DOI: 10.1088/1757-899X/1038/1/012076.
• [6] Čepon G., Manin L., Boltežar M.: Experimental identification of the contact parameters between a V-ribbed belt and a pulley. Mechanism and Machine Theory. 2010, 45(10), 1424–1433, DOI: 10.1016/j.mechmachtheory.2010.05.006.
• [7] Čepon G., Manin L., Boltežar M.: Introduction of damping into the flexible multibody belt-drive model: A numerical and experimental investigation. Journal of Sound and Vibration. 2009, 324(1–2), 283–296, DOI: 10.1016/j.jsv.2009.02.001.
• [8] Čepon G., Manin L., Boltežar M.: Validation of a flexible multibody belt-drive model. Strojniški vestnik – Journal of Mechanical Engineering. 2011, 57(7–8), 539–546, DOI: 10.5545/sv-jme.2010.257.
• [9] Chowdhury S., Yedavalli R.K.: Dynamics of belt-pulley-shaft systems. Mechanism and Machine Theory. 2016, 98, 199–215, DOI: 10.1016/j.mechmachtheory.2015.11.011.
• [10] Cruz-Gómez M.A., Gallardo-Hernández E.A., Vite-Torrez M., Peña Bautista A.: Rubber steel friction in contaminated contacts. Wear. 2013, 302(1–2), 1421–1425, DOI: 10.1016/j.wear.2013.01.087.
• [11] Dakel M., Jézéquel L., Sortais J.-L.: Stationary and transient analyses of a pulley-belt system based on an Eulerian approach. Mechanism and Machine Theory. 2018 128, 682–707, DOI: 10.1016/j.mechmachtheory.2018.07.002.
• [12] Frendo F., Bucchi F.: “Brush model” for the analysis of flat belt transmissions in steady-state conditions. Mechanism and Machine Theory. 2020, 143, DOI: 10.1016/j.mechmachtheory.2019.103653.
• [13] Higgins D.D., Marmo B.A., Jeffree C.E., Koutsos V., Blackford J.R.: Morphology of ice wear from rubber–ice friction tests and its dependence on temperature and sliding velocity. Wear. 2008,265(5–6), 634–644, DOI: 10.1016/j.wear.2007.12.015.
• [14] Hu Y., Zhu H., Zhu W.D., Li Ch., Pi Y.: Dynamic performance of a multi-ribbed belt based on an overlay constitutive model of carbon-black-filled rubber and experimental validation. Mechanical Systems and Signal Processing. 2017, 95, 252–272, DOI: 10.1016/j.ymssp.2017.03.013.
• [15] Julio G., Plante J.S.: An experimentally-validated model of rubber-belt CVT mechanics. Mechanism and Machine Theory. 2011, 46(8), 1037–1053, DOI: 10.1016/j.mechmachtheory.2011.04.001.
• [16] Kim D., Leamy M.J., Ferri A.A.: Dynamic Modeling and Stability Analysis of Flat Belt Drives Using an Elastic/Perfectly Plastic Friction Law. Journal of Dynamic Systems Measurement and Control – transactions of the ASME. 2011, 133(4), 1–10, DOI: 10.1115/1.4003796.
• [17] Krawiec P., Waluś K., Warguła Ł., Adamiec J.: Wear evaluation of elements of V-belt transmission with the application of optical microscope. MATEC Web of Conferences. 2018, 157, 01009, DOI:10.1051/matecconf/201815701009.
• [18] Kubas K.: A model for the dynamic analysis of a belt transmission using the Dahl friction model. Journal of Theoretical and Applied Mechanics. 2017, 55(4), 1423–1435, DOI: 10.15632/jtampl.55.4.1423.
• [19] Kubas K., Harlecki A.: Dynamic analysis of a belt transmission with the GMS friction model. Meccanica. 2021, 56(9), 2293–2305, DOI: 10.1007/s11012-021-01358-8.
• [20] Leamy M.J., Wasfy T.M.: Analysis of belt-driven mechanics using a creep-rate-dependent friction law. ASME Journal of Applied Mechanics. 2002, 69(6), 763–771, DOI: 10.1115/1.1488663.
• [21] Leamy M.J., Wasfy T.M.: Dynamic finite element modeling of belt drives. 18th Biennial Conference on Mechanical Vibration and Noise, ASME 2001 International Design Engineering Technical Conferences and Computers and Information in Engineering Conference. 2001, 6A, 365–371, DOI: 10.1115/DETC2001/VIB-21342.
• [22] Leamy M.J., Wasfy T.M.: Transient and Steady-State Dynamic Finite Element Modeling of BeltDrives. ASME Journal of Dynamic Systems, Measurement, and Control. 2002, 124(4), 575–581, DOI:10.1115/1.1513793.
• [23] Li K.W., Chen C.J.: The effect of shoe soling thread groove width on the coefficient of friction with mdifferent sole materials, floors, and contaminants. Applied Ergonomics. 2004, 35(6), 499–507, DOI:10.1016/j.apergo.2004.06.010.
• [24] Manin L., Liang X., Lorenzon C.: Power losses prediction in poly-v belt transmissions: application to front engine accessory drives. International Gear Conference. Lyon, Chandos Publishing. 2014,1162–1171, DOI: 10.1533/9781782421955.1162.
• [25] Manin L., Lorenzon C., Saad H.: Belt-pulley friction coefficient, experimental analysis: Influence of the Poly-V belt material components and contact pressure. Proceedings of the International Conference on Power Transmissions. Chongqing, P.R. China, 2016, 0(191039), 47–51, DOI:10.1201/9781315386829-9.
• [26] Mascenik J., Murcinkowa Z.: Experimental determination of the belt transmission slip. Man-agement Systems in Production Engineering. 2019, 4(27), 205–210, DOI: 10.1515/mspe-2019-0032.
• [27] Mofidi M., Kassfeldt E., Prakash B.: Tribological behaviour of an elastomer aged in different oils. Tribology International. 2008, 41(9–10), 860–866, DOI: 10.1016/j.triboint.2007.11.013.
• [28] Oborin E., Vetyukov Y., Steinbrecher I.: Eulerian description of non-stationary motion of an idealized belt-pulley system with dry friction. International Journal of Solids and Structures. 2018, 147, 40–51, DOI: 10.1016/j.ijsolstr.2018.04.007.
• [29] Oborin E.: Belt–pulley interaction: role of the action line of friction forces. Acta Mechanica. 2020, 231(9), 3979–3987, DOI: 10.1007/s00707-020-02724-5.
• [30] Pan Y., Liu X., Shan Y., Chen G.(S.): Complex modal analysis of serpentine belt drives on beam coupling model. Mechanism and Machine Theory. 2017, 116, 162–177, DOI: 10.1016/j.mechmachtheory.2017.05.016.
• [31] Silva C.A.F., Manin L., Andrianoely M.A., Besnier E., Redmond D.: Power losses distribution in serpentine belt drive: Modelling and experiments. Proceedings of the Institution of Mechanical Engineers. Part D. Journal of Automobile Engineering. 2019, 233(13), 3424–3437, DOI: 10.1177/0954407018824943.
• [32] Yamaguchi T., Umetsu T., Ishizuka Y., Kasuga K., Ito T., Ishizawa S., et al.: Development of new footwear sole surface pattern for prevention of slip-related falls. Safety Science. 2012, 50(4), 986–994, DOI: 10.1016/j.ssci.2011.12.017.