Studies of the Corrosion Resistance Properties of Bone Screws Made from 316L Stainless Steel in Ringer's Solution

• Autorzy: Kajzer A. , Antonowicz M. , Ziębowicz B.

Identyfikatory

DOI

10.24425/118944

• Języki publikacji: EN

Abstrakty

EN

Stainless steel 316L is one of the most common metallic biomaterials used for implants. Its passive surface provides a good corrosion resistance in the body environment, which can be reduced by surface mechanical damages. This is the reason why the bone screws made of stainless steel 316L were subjected to laboratory analysis in the initial state, after diversified implantation period and after mechanical damage of the surface. The mechanical damages were estimated on the basis of stereoscopic and scanning electron microscope (SEM). In order to estimate the pitting and crevice corrosion resistance, potentiodynamic and potentiostatic examinations were performed. On the basis of obtained results it can be stated that despite the visible damages on the surface, the investigated screws present a good pitting corrosion resistance. However, the way the screws were fastened caused frictional corrosion and existing cavities led to crevice corrosion. Moreover, clear correlation between magnitude of mechanical damages of the surface, implantation time and screws corrosion resistance was observed.

Słowa kluczowe

EN

bone screw; 316L steel; pitting corrosion; crevice corrosion; SEM

• Wydawca: Institute of Metallurgy and Materials Science of Polish Academy of Sciences ; Committee of Materials Engineering and Metallurgy of Polish Academy of Sciences
• Czasopismo: Archives of Metallurgy and Materials
• Rocznik: 2018
• Tom: Vol. 63, iss. 1
• Strony: 323--328
• Opis fizyczny: Bibliogr. 39 poz., rys., tab.

Twórcy

autor

Kajzer A.

• Silesian University of Technology, Department of Engineering Materials and Biomaterials Faculty of Biomedical Engineering, 40 Roosevelta Str., 41-800 Zabrze, Poland

autor

Antonowicz M.

• Silesian University of Technology, Department of Engineering Materials and Biomaterials Faculty of Biomedical Engineering, 40 Roosevelta Str., 41-800 Zabrze, Poland

autor

Ziębowicz B.

• Silesian University of Technology, Faculty of Mechanical, Institute of Engineering Materials and Biomaterials Engineering, 44-100 Gliwice, Poland

Bibliografia

• [1] J. Marciniak, W. Chrzanowski, A. Kajzer, Gwoździowanie Śródszpikowe w Osteosyntezie, 2008 Gliwice.
• [2] M. Basiaga, W. Kajzer, W. Walke, A. Kajzer, M. Kaczmarek, Mater. Sci. Eng. C 68, 851-860 (2016).
• [3] A. Kajzer, W. Kajzer, J. Dzielicki, D. Matejczyk, Acta of Bioeng. and Biomechanics 2, 35-44 (2015).
• [4] W. Walke, Z. Paszenda, M. Basiaga, P. Karasiński, M. Kaczmarek, EIS study of SiO2 Oxide Film on 316L stainless steel for cardiac implants. Information Technologies in Biomedicine. in:, Advances in Intelligent Systems and Computing (284), Springer 2014.
• [5] K. Y. Chiu, F. T. Cheng, H. C. Man, Surf. Coat. Technol. 200, 6054 (2006).
• [6] V. Muthukurman, V. Selladurai, S. Nandhakumar et. Al., Mater. Des. 31, 2813 (2010).
• [7] M. A. H. Gepreel, M. Niinomi, J. Mech. Beh. Biomed. Mater. 20, 407-415 (2013).
• [8] V. Barranco, M. L. Escudero, M. C. Garcia-Alonso, Electrochim. Acta. 53 (13), 4374-4384 (2007).
• [9] W. Wu, X. Liu, H. Han, J. Mater. Sci. Technol. 24, 926 (2008).
• [10] Y. Okazaki, E. Gotoh, Corros. Sci. 50, 3429 (2008).
• [11] I. Gurappa, Mater. Charact. 49, 73 (2002).
• [12] Tiwari, J. Zhu, L. H. Hihara, Surf. Coat. Technol. 202, 4620 (2008).
• [13] Vesel, M. Mozetic, A. Drenik, et. Al., Appl. Surf. Sci. 32, 1759 (2008)
• [14] A. Samide, I. Bibicu, opera, et.al, J. Optoelectron. Adv. Mater. 10, 1431 (2008).
• [15] S. Steinmann, Corrosion of Surgical Implants – in vivo, in vitro test. In. Winten et al., John Viley Sons, Advances in Biomaterials., Chirchester 1980.
• [16] J. J. Joshua, J. L. Gilbert, R. M. Urban, J Bone, Joint Surg. 80, 268-282 (1998).
• [17] H. Zhao, J. V. Humbeeck, J. Mater. Sci. Mater. Med. 13, 911 (2002).
• [18] J. S. Noh, N. J. Laycock, W. Gao, D. B. Wells, Corros. Sci. 42(12), 2069-2084 (2000).
• [19] J. Marciniak, Biomateriały, 2013 Wydawnictwo Politechniki Śląskiej, Gliwice.
• [20] A. Latifi, M. Imani, M. T. Khorasani, M. D. Joupari, Surf. Coat. Technol. 221, 1-12 (2013).
• [21] C. Teodoro dos Santos, C. Barbosa, M. de Jesus Monteiro, I. de Cerqueira Abud, I. M. V. Caminha, C. R. de Mello Roesler, Research on Biomedical Engineering 31 (2), 169-175 (2015).
• [22] T. Anita, M. G. Pujar, H. Shaikh, R. K. Dayal, H. S. Khatak, Corros. Sci. 48, 2689-2710 (2006).
• [23] J. Y. Huang, J. J. Yeh, S. L. Jeng, C. Y. Chen, R. C. Kuo, Mater.Trans. 47 (2), 409-417 (2006).
• [24] T. M. Sridhar, S. P. Vinodhini, U. Kamachi Mudali, B. Venkatachalapthy, K. Ravichandran, Mater. Technol. 31 (12), 705-718 (2016).
• [25] G. Mori, H. Dosinger, J. Mater. Sci. 249-254 (2004).
• [26] M. Basiaga, W. Walke, Z. Paszenda, A. Kajzer, Materials and Technology 50 (1), 153-158 (2016).
• [27] J. Szewczenko, M. Pochrząst, W. Walke, Prz. Elektrotech. 87 (12B), 177-180 (2011).
• [28] J. Szewczenko, J. Marciniak, J. Tyrlik-Held, K. Nowińska, Effect of Surface Pretreatment on Corrosion Resistance of Anodically Oxidized Ti6Al7Nb Alloy. In. Lecture Notes in Bioinformatics. 7339, 2012 Springer-Verlag Berlin Heidelberg.
• [29] Standard ISO 5832-1: Implants for surgery – Metallic materials – Part 1: Wrought stainless steel (2007).
• [30] B. Krzywański, Master thesis, Silesian University of Technology, Zabrze, Poland (2011).
• [31] A. Poursaee, Cement Concrete Res. 40, 1451-1458 (2010).
• [32] Standard ASTM F746 – 04 – Standard Test Method for Pitting or Crevice Corrosion of Metallic Surgical Implant Materials (2009).
• [33] M. Yazıcı, Çomaklı, T. Yetim, A.F. Yetim, A. Çelik, Surf. Coat. Technol. 261 (15), 181-188 (2015)
• [34] H. Yang, K. Yang, B. Zhanga. Mater. Lett. 61, 1154-1157 (2007).
• [35] S. Habibzadeh, L. Ling, D. Shum-Tim, E. C. Davis, S. Corros. Sci. 87, 89-100 (2014).
• [36] S. V. Muley, A. N. Vidvans, G. P. Chaudhari, S. Udainiya, Acta Biomater 30, 408-419 (2016).
• [37] U. Mudali, T. M . Sridhar, B. Raj, Sādhanā 28 (3,4), 601-637 India (2003).
• [38] G. Manivasagam, D. Dhinasekaran, A. Rajamanickam, Recent Patents on Corrosion Science, 2, 40-54 (2010).
• [39] W. Kajzer, M. Kaczmarek, J. Marciniak, J. Mater. Process. Technol. (162-163), 196-202 (2005).

Uwagi

PL

Opracowanie rekordu w ramach umowy 509/P-DUN/2018 ze środków MNiSW przeznaczonych na działalność upowszechniającą naukę (2018).