Effect of Delta Ferrite on the Mechanical Properties of Dissimilar Ferritic-Austenitic Stainless Steel Welds

• Autorzy: Ghasemi R. , Beidokhti B. , Fazel-Najafabadi M.

Identyfikatory

DOI

10.24425/118958

• Języki publikacji: EN

Abstrakty

EN

The dissimilar welds of AISI 304 to AISI 430 stainless steel was investigated by using gas tungsten arc welding. Three filler metals including ER309L, ER316L and ER2594 were applied. The weakest region of the welds was the heat affected zone of 430 stainless steel due to the formation of martensite. Also, the wide grain growth zone was observed in this side. The ferrite number for type 309L, 316L and 2594 weld metals was about 15, 32 and 57, respectively. The hardness and tensile strength values of the weld metals were higher than that of the heat affected zones and the base metals. The ferrite presented higher hardness values than the austenite in type 316L and 309L joints; while the hardness of austenite and ferrite was comparable in type 2594 weld metal.

Słowa kluczowe

EN

stainless steel; welding; delta ferrite; electron microscopy; austenite

• Wydawca: Institute of Metallurgy and Materials Science of Polish Academy of Sciences ; Committee of Materials Engineering and Metallurgy of Polish Academy of Sciences
• Czasopismo: Archives of Metallurgy and Materials
• Rocznik: 2018
• Tom: Vol. 63, iss. 1
• Strony: 437--443
• Opis fizyczny: Bibliogr. 31 poz., rys., tab.

Twórcy

autor

Ghasemi R.

• Islamic Azad University, Najafabad Branch, Department of Materials Engineering, Isfahan, Iran

autor

Beidokhti B.

• Ferdowsi University of Mashhad, Materials and Metallurgical Engineering Department, Faculty of Engineering, Mashhad, Iran

autor

Fazel-Najafabadi M.

• Payame Noor University, Department of Mechanical Engineering, Tehran, Iran

Bibliografia

• [1] T. Mohandas, M. G. Reddy, M. Naveed, J. Mater. Process. Technol. 94, 133-140 (1999).
• [2] J. C. Lippold, D. J. Kotecki, Welding Metallurgy and Weldability of Stainless Steels, 2005 Wiley-Interscience, New Jersey, Hoboken.
• [3] F. B. Pickering, Int. Met. Rev. 21, 227-268 (1976).
• [4] S. Kumar, A. S. Shahi, Mater. Design 32, 3617-3623 (2011).
• [5] M. Shojaati, B. Beidokhti, Constr. Build. Mater. 147, 608-615 (2017).
• [6] C. J. Long, W. T. Delong, Weld. J. 32, 281s-297s (1973).
• [7] C. C. Hsieh, D. Y. Lin, M. C. Chen, W. Wu, Mater. Sci. Eng. A 477, 328-333 (2008).
• [8] K. Shanmugam, A. K. Lakshminarayanan, V. Balasubramanian, Int. J. Mater. Sci. Technol. 25, 181-186 (2009).
• [9] D. J. Kotecki, Weld. J. 84, 14s-16s (2005).
• [10] M. Mukherjee, T. K. Pal, J. Mater. Sci. Technol. 28, 343-352 (2012).
• [11] A. F. Padilha, C. F. Tavares, M. A. Martorano, Mater. Sci. Forum 730-732, 733-738 (2013).
• [12] T. Maki, C. M. Wayman, Acta Metall. 25, 681-693 (1977).
• [13] X. M. Zhang, E. Gautier, A. Simon, Acta Metall. 37, 477-485 (1989).
• [14] E. Taban, E. Kaluc, A. Dhooge, Mater. Design 30, 4236-4242 (2009).
• [15] T. D. Anderson, M. J. Perricone, J. N. Dupont, A. R. Marder, Weld. J. 86, 281s-292s (2007).
• [16] J. A. Brooks, A. Thompson, Int. Mater. Rev. 36, 16-44 (1991).
• [17] L. Li, R. W. Messler, Jr., Weld. J. 5, 78s-84s (2002).
• [18] Y. Arata, F. Matsuda, H. Nakagawa, S. Katayama, Trans. JWRI 7, 21-24 (1978).
• [19] J. A. Brooks, Weld. J. 54, 189s-195s (1975).
• [20] M. van Warmelo, D. Nolan, J. Norrish, Mater. Sci. Eng. A 464, 157-169 (2007).
• [21] M. M. A. Khan, L. Romoli, M. Fiaschi, G. Dini, F. Sarri, J. Mater. Process. Technol. 212, 856-867 (2012).
• [22] C. T. Kwok, S. L. Fong, F. T. Cheng, H. C. Man, J. Mater. Process. Technol. 176, 168-178 (2006).
• [23] W. Reick, M. Pohl, A. F. Padilha, ISIJ Int. 38, 567-571 (1998).
• [24] R. E. Avery, Pay Attention to Dissimilar-Metal Welds: Guidelines for Welding Dissimilar Metals, 1991, Nickel Development Institute, Toronto.
• [25] D. J. Lee, K. H. Jung, J. H. Sung, Y. H. Kim, K. H. Lee, J. U. Park, Y. T. Shin, H. W. Lee, Mater. Design 30, 3269-3273 (2009).
• [26] U. Caligulu, H. Dikbas, M. Taskin, Gazi U. J. Sci. 25, 35-51 (2012).
• [27] L. J. Ayers, The Hardening of Type 316L Stainless Steel Welds with Thermal Aging. B.Sc. Thesis, Massachusetts Institute of Technology, Massachusetts, 2012.
• [28] Y. Cao, Y. B. Wang, X. H. An, X. Z. Liao, M. Kawasaki, S.P. Ringer, T. G. Langdon, Y.T. Zhu, Acta Mater. 63, 16-29 (2014).
• [29] C. J. Huang, D. J. Browne, S. McFadden, Acta Mater. 54, 11-21 (2006).
• [30] T. Sakaki, K. Sugimoto, T. Fukuzato, Acta Metall. 31, 1737-1746 (1983).
• [31] S. K. Paul, Mater. Design 50, 782-789 (2013).

Uwagi

PL

Opracowanie rekordu w ramach umowy 509/P-DUN/2018 ze środków MNiSW przeznaczonych na działalność upowszechniającą naukę (2018).