The Influence of Physical Properties of C55 Alloy on Geometry of Flow in the Process of Shaping

• Autorzy: Nabrdalik Marcin , Sobociński Michał

Identyfikatory

DOI

10.24425/amm.2024.149101

• Języki publikacji: EN

Abstrakty

EN

The paper presents analysis of influence of change of physical parameters such as: temperature, friction coefficient and load, during the process of die forging. Optimization of the process effects in achieving high quality products, decreasing shaping resistance, and what follows - lower energy consumption. Temperature is the basic factor affecting the process of plastic working. Analyzing that influence in individual die fragments, allows to engineer the flow of shaped material. The QForm3D commercial program for finite element method calculations was used for numerical simulations. The paper presents multi-variant analysis of forging process with the usage of numerical simulation, which provided many valuable information concerning changes of key parameters, such as: temperature, stress and strain distribution and variations of technological parameters, as well as their mutual influence, difficult to obtain in analysis of industrial process.

Słowa kluczowe

EN

die forging; FEM; drop forging; simulation methods; QForm3D

• Wydawca: Institute of Metallurgy and Materials Science of Polish Academy of Sciences ; Committee of Materials Engineering and Metallurgy of Polish Academy of Sciences
• Czasopismo: Archives of Metallurgy and Materials
• Rocznik: 2024
• Tom: Vol. 69, iss. 1
• Strony: 353--357
• Opis fizyczny: Bibliogr. 14 poz., fot., rys., tab.

Twórcy

autor

Nabrdalik Marcin

• Czestochowa University of Technology, Faculty of Mechanical Engineering and Computer Science, Department of Technology and Automation, 21 Armii Krajowej Av., 42-201 Czestochowa, Poland

• https://orcid.org/0000-0002-5536-4317

autor

Sobociński Michał

• Czestochowa University of Technology, Faculty of Mechanical Engineering and Computer Science, Department of Technology and Automation, 21 Armii Krajowej Av., 42-201 Czestochowa, Poland

• https://orcid.org/0000-0002-9651-5564

Bibliografia

• [1] P. Wasiunyk, J. Jarocki, Kuźnictwo i Prasownictwo. Warszawa (1977).
• [2] P. Wasiunyk, Kucie matrycowe. Warszawa (1987).
• [3] M. Czarnecki, B. Filip, M. Szala, Jour. of Tech. and Expl. in Mech. Eng. 1, 150-165 (2015).
• [4] Z. Pater, Obr. Plast. Met. 3, XVIII, 23-29 (2007).
• [5] A. Żmudzki, P. Skubisz, J. Sińczak, Obr. Plast. Met. 3, XVII, 9-19 (2006).
• [6] S. Li, H. Ji, B. Wang, Y. Mu, Arch. Civ. Mech. Eng. 19, 391-404 (2019). DOI: https://doi.org/10.1016/j.acme.2018.11.006
• [7] M. Hawryluk, M. Kaszuba, Z. Gronostajski, S. Polak, J, Ziemba, CIRP-JMST, 30, 87-93 (2020). DOI: https://doi.org/10.1016/j.cirpj.2020.04.005
• [8] B. Behrens, W. Volk, D. Maier, L. Scandola, Proc. Manuf. 47, 295-300 (2020). DOI: https://doi.org/10.1016/j.promfg.2020.04.231
• [9] R. Hari Krishna, D.P. Jena, Measurement, 134, 855-865 (2019). DOI: https://doi.org/10.1016/j.measurement.2018.12.023
• [10] X. Feng, L. Hu, Y. Sun, Z. Liu, Proc. Manuf. 37, 478-485 (2019). DOI: https://doi.org/10.1016/j.promfg.2019.12.077
• [11] M. Dalbosco, G. Lopes, P. Schmitt, Jour. of Manuf. Proc. 64, 349-355 (2021). DOI: https://doi.org/10.1016/j.jmapro.2021.01.039
• [12] M. Hawryluk, J. Ziemba, M. Zwierzchowski, M. Janik, Wear 476, 203749 (2021). DOI: https://doi.org/10.1016/j.wear.2021.203749
• [13] https://www.solidworks.pl/cad-3d, accessed: 21.03.2022.
• [14] https://www.qform3d.com, accessed: 21.03.2022.