Effect of shot peening on the surface properties, corrosion and wear performance of 17-4PH steel produced by DMLS additive manufacturing

• Autorzy: Walczak Mariusz , Szala Mirosław

Identyfikatory

DOI

10.1007/s43452-021-00306-3

• Języki publikacji: EN

Abstrakty

EN

Components produced by additive manufacturing (AM) via direct metal laser sintering (DMLS) have typical as-fabricated surface defects. As a result, surface properties of AM products should be modified to increase their strength, anti-wear behaviour, and at the same time to ensure their high corrosion resistance. Surface modification via shot peening is considered suitable for additive manufacturing of medical devices made of 17-4PH stainless steel. The objective of this study was to determine the effect of shot peening pressures (0.3 MPa and 0.6 MPa) and three types of blasting media (CrNi steel shot, nutshell granules and ceramic beads) on the tribological characteristics and corrosion resistance of specimens of DMLS 17-4PH stainless steel. Results demonstrated that shot peening caused steel microstructure refinement and-except for the nutshell shot-peened specimens-induced both martensite (α) formation and retained austenite (γ) reduction. 17-4PH specimens peened with steel and ceramic shots showed the highest increase in surface hardening by approx. ~ 119% (from 247 to 542 HV), which significantly improved their wear resistance. The highest mechanical properties (hardness and wear resistance) and corrosion resistance were obtained for the surfaces modified using the following media: ceramic beads > CrNi steel shot > nutshell granules. Adhesive and fatigue wear were two predominant mechanisms of tribological deterioration. Results demonstrated that the application of shot peening using ceramic beads led to grain size refinement from 22.0 to 14.6 nm and surface roughness reduction, which in turn resulted in higher corrosion resistance of the material. DMLS 17-4PH specimens modified by shot peening using ceramic beads and a pressure of 0.6 MPa exhibited the optimum surface morphology, hardness and microstructure, and thus improved wear and corrosion performance.

Słowa kluczowe

EN

shot peening; 17-4PH steel; corrosion; wear; surface engineering; additive manufacturing; tribology

PL

trybologia; inżynieria powierzchni; zużycie

• Wydawca: Springer ; Wrocław University of Science and Technology
• Czasopismo: Archives of Civil and Mechanical Engineering
• Rocznik: 2021
• Tom: Vol. 21, no. 4
• Strony: 368--387
• Opis fizyczny: Bibliogr. 48 poz., rys., wykr.

Twórcy

autor

Walczak Mariusz

• Department of Materials Engineering, Faculty of Mechanical Engineering, Lublin University of Technology, Nadbystrzycka 36, 20-618 Lublin, Poland

• https://orcid.org/0000-0001-6728-9134

autor

Szala Mirosław

• Department of Materials Engineering, Faculty of Mechanical Engineering, Lublin University of Technology, Nadbystrzycka 36, 20-618 Lublin, Poland

• https://orcid.org/0000-0003-1059-8854

Bibliografia

• [1] Lashgari HR, Kong C, Adabifiroozjaei E, Li S. Microstructure, post thermal treatment response, and tribological properties of 3D printed 17-4 PH stainless steel. Wear. 2020;456–457: 203367. https://doi.org/10.1016/j.wear.2020.203367.
• [2] Palanisamy D, Senthil P, Senthilkumar V. The effect of aging on machinability of 15Cr–5Ni precipitation hardened stainless steel. Archiv Civ Mech Eng. 2016;16:53–63. https://doi.org/10.1016/j.acme.2015.09.004.
• [3] Zai L, Zhang C, Wang Y, Guo W, Wellmann D, Tong X, Tian Y. Laser powder bed fusion of precipitation-hardened martensitic stainless steels: a review. Metals. 2020;10:255. https://doi.org/10.3390/met10020255.
• [4] Groarke R, Danilenkoff C, Karam S, McCarthy E, Michel B, Mussatto A, Sloane J, O’Neill A, Raghavendra R, Brabazon D. 316L stainless steel powders for additive manufacturing: relationships of powder rheology, size, size distribution to part properties. Materials. 2020;13:5537. https://doi.org/10.3390/ma13235537.
• [5] Macek W, Branco R, Trembacz J, Costa JD, Ferreira JAM, Capela C. Effect of multiaxial bending-torsion loading on fracture surface parameters in high-strength steels processed by conventional and additive manufacturing. Eng Fail Anal. 2020;118: 104784. https://doi.org/10.1016/j.engfailanal.2020.104784.
• [6] Haghdadi N, Laleh M, Moyle M, Primig S. Additive manufacturing of steels: a review of achievements and challenges. J Mater Sci. 2021;56:64–107. https://doi.org/10.1007/s10853-020-05109-0.
• [7] Li C, Liu ZY, Fang XY, Guo YB. Residual stress in metal additive manufacturing. Procedia CIRP. 2018;71:348–53. https://doi.org/10.1016/j.procir.2018.05.039.
• [8] Kaszuba M, Widomski P, Białucki P, Lange A, Boryczko B, Walczak M. Properties of new-generation hybrid layers combining hardfacing and nitriding dedicated to improvement in forging tools’ durability. Arch Civ Mech Eng. 2020;20:78. https://doi.org/10.1007/s43452-020-00080-8.
• [9] Winnicki M, Małachowska A, Piwowarczyk T, Rutkowska-Gorczyca M, Ambroziak A. The bond strength of Al+Al 2 O 3 cermet coatings deposited by low-pressure cold spraying. Arch Civ Mech Eng. 2016;16:743–52. https://doi.org/10.1016/j.acme.2016.04.014.
• [10] Łatka L, Michalak M, Szala M, Walczak M, Sokołowski P, Ambroziak A. Influence of 13 wt% TiO 2 content in alumina–titania powders on microstructure, sliding wear and cavitation erosion resistance of APS sprayed coatings. Surf Coat Technol. 2021;410: 126979. https://doi.org/10.1016/j.surfcoat.2021.126979.
• [11] Benedetti M, Torresani E, Leoni M, Fontanari V, Bandini M, Pederzolli C, Potrich C. The effect of post-sintering treatments on the fatigue and biological behavior of Ti–6Al-4V ELI parts made by selective laser melting. J Mech Behav Biomed Mater. 2017;71:295–306. https://doi.org/10.1016/j.jmbbm.2017.03.024.
• [12] Harun WSW, Manam NS, Kamariah MSIN, Sharif S, Zulkifly AH, Ahmad I, Miura H. A review of powdered additive manufacturing techniques for Ti-6al-4v biomedical applications. Powder Technol. 2018;331:74–97. https://doi.org/10.1016/j.powtec.2018.03.010.
• [13] de Peltz JS, Beltrami LVR, Kunst SR, Brandolt C, de Malfatti CF. Effect of the shot peening process on the corrosion and oxidation resistance of AISI430 stainless steel. Mater Res. 2015;18:538–45. https://doi.org/10.1590/1516-1439.316514.
• [14] Kameyama Y, Komotori J. Effect of micro ploughing during fine particle peening process on the microstructure of metallic materials. J Mater Process Technol. 2009;209:6146–55. https://doi.org/10.1016/j.jmatprotec.2009.08.010.
• [15] Trung PQ, Khun NW, Butler DL. Effects of shot peening pressure, media type and double shot peening on the microstructure, mechanical and tribological properties of low-alloy steel. Surf Topogr Metrol Prop. 2016;4:045001. https://doi.org/10.1088/2051-672X/4/4/045001.
• [16] Kovacı H, Bozkurt YB, Yetim AF, Aslan M, Çelik A. The effect of surface plastic deformation produced by shot peening on corrosion behavior of a low-alloy steel. Surf Coat Technol. 2019;360:78–86. https://doi.org/10.1016/j.surfcoat.2019.01.003.
• [17] Żebrowski R, Walczak M. Effect of the shot peening on surface properties and tribological performance of Ti-6Al-4V alloy produced by means of DMLS technology. Arch Metall Mater. 2019;64:377–83. https://doi.org/10.24425/amm.2019.126263.
• [18] Żebrowski R, Walczak M, Klepka T, Pasierbiewicz K. Effect of the shot peening on surface properties of Ti-6Al-4V alloy produced by means of DMLS technology. Eksploatacja i Niezawodnosc. 2019;21:46–53. https://doi.org/10.17531/ein.2019.1.6.
• [19] Żebrowski R, Walczak M, Korga A, Iwan M, Szala M. Effect of shot peening on the mechanical properties and cytotoxicity behaviour of titanium implants produced by 3D printing technology. J Healthc Eng. 2019. https://doi.org/10.1155/2019/8169538.
• [20] Dehghan-Manshadi A, Yu P, Dargusch M, StJohn D, Qian M. Metal injection moulding of surgical tools, biomaterials and medical devices: a review. Powder Technol. 2020;364:189–204. https://doi.org/10.1016/j.powtec.2020.01.073.
• [21] Ganesh BKC, Sha W, Ramanaiah N, Krishnaiah A. Effect of shot-peening on sliding wear and tensile behavior of titanium implant alloys. Mater Des (1980–2015). 2014;56:480–6. https://doi.org/10.1016/j.matdes.2013.11.052.
• [22] Obata M, Sudo A (1993) Effect of shot peening on residual stress and stress corrosion cracking for cold worked austenitic stainless steel. In: Conf Proc: ICSP-5. pp 257–264.
• [23] Dorr T, Hilpert M, Beckmerhagen P, Kiefer A, Wagner L (1999) Influence of shot peening on fatigue performance of high-strengthaluminum-and magnesium alloys. In: Proceedings of the ICSP-7 Conference, Warsaw, Poland, pp 153–160.
• [24] Ahmed AA, Mhaede M, Wollmann M, Wagner L. Effect of micro shot peening on the mechanical properties and corrosion behavior of two microstructure Ti–6Al–4V alloy. Appl Surf Sci. 2016;363:50–8. https://doi.org/10.1016/j.apsusc.2015.12.019.
• [25] Thijs L, Kempen K, Kruth J-P, Van Humbeeck J. Fine-structured aluminium products with controllable texture by selective laser melting of pre-alloyed AlSi10Mg powder. Acta Mater. 2013;61:1809–19. https://doi.org/10.1016/j.actamat.2012.11.052.
• [26] Yadroitsev I, Krakhmalev P, Yadroitsava I. Hierarchical design principles of selective laser melting for high quality metallic objects. Addit Manuf. 2015;7:45–56. https://doi.org/10.1016/j.addma.2014.12.007.
• [27] Matilainen V-P, Piili H, Salminen A, Nyrhilä O. Preliminary investigation of keyhole phenomena during single layer fabrication in laser additive manufacturing of stainless steel. Phys Procedia. 2015;78:377–87. https://doi.org/10.1016/j.phpro.2015.11.052.
• [28] Solakoğlu EU, Gürgen S, Kuşhan MC. Surface topography of nickel-based superalloy manufactured with direct metal laser sintering (DMLS) method. Surf Topogr Metrol Prop. 2019;7:015012. https://doi.org/10.1088/2051-672X/aafe33.
• [29] Murr LE, Martinez E, Hernandez J, Collins S, Amato KN, Gaytan SM, Shindo PW. Microstructures and properties of 17–4 PH stainless steel fabricated by selective laser melting. J Market Res. 2012;1:167–77. https://doi.org/10.1016/S2238-7854(12)70029-7.
• [30] Cheruvathur S, Lass EA, Campbell CE. Additive manufacturing of 17–4 PH stainless steel: post-processing Heat treatment to achieve uniform reproducible microstructure. JOM. 2016;68:930–42. https://doi.org/10.1007/s11837-015-1754-4.
• [31] Dieter GE, Bacon D. Mechanical metallurgy. McGraw-Hill; 1988.
• [32] Jelliti S, Richard C, Retraint D, Roland T, Chemkhi M, Demangel C. Effect of surface nanocrystallization on the corrosion behavior of Ti–6Al–4V titanium alloy. Surf Coat Technol. 2013;224:82–7. https://doi.org/10.1016/j.surfcoat.2013.02.052.
• [33] Gahr K-HZ. Microstructure and wear of materials. Elsevier; 1987.
• [34] Gürgen S. Wear performance of UHMWPE based composites including nano-sized fumed silica. Compos B Eng. 2019;173: 106967. https://doi.org/10.1016/j.compositesb.2019.106967.
• [35] Gürgen S, Çelik ON, Kuşhan MC. Tribological behavior of UHM-WPE matrix composites reinforced with PTFE particles and aramid fibers. Compos B Eng. 2019;173: 106949. https://doi.org/10.1016/j.compositesb.2019.106949.
• [36] AlMangour B, Yang J-M. Improving the surface quality and mechanical properties by shot-peening of 17-4 stainless steel fabricated by additive manufacturing. Mater Des. 2016;110:914–24. https://doi.org/10.1016/j.matdes.2016.08.037.
• [37] Wang ZB, Tao NR, Li S, Wang W, Liu G, Lu J, Lu K. Effect of surface nanocrystallization on friction and wear properties in low carbon steel. Mater Sci Eng A. 2003;352:144–9. https://doi.org/10.1016/S0921-5093(02)00870-5.
• [38] Szala M, Łatka L, Walczak M, Winnicki M. Comparative study on the cavitation erosion and sliding wear of cold-sprayed Al/Al2O3 and Cu/Al2O3 coatings, and stainless steel aluminium alloy, copper and brass. Metals. 2020;10:856. https://doi.org/10.3390/met10070856.
• [39] Lashgari HR, Li S, Kong C, Asnavandi M, Zangeneh Sh. Rotary friction welding of additively manufactured 17-4PH stainless steel. J Manuf Process. 2021;64:1517–28. https://doi.org/10.1016/j.jmapro.2021.03.008.
• [40] Yang Y, Zhu Y, Khonsari MM, Yang H. Wear anisotropy of selective laser melted 316L stainless steel. Wear. 2019;428–429:376–86. https://doi.org/10.1016/j.wear.2019.04.001.
• [41] Kc S, Nezhadfar PD, Phillips C, Kennedy MS, Shamsaei N, Jackson RL. Tribological behavior of 17-4 PH stainless steel fabricated by traditional manufacturing and laser-based additive manufacturing methods. Wear. 2019;440–441: 203100. https://doi.org/10.1016/j.wear.2019.203100.
• [42] Ameer MA, Khamis E, Al-Motlaq M. Electrochemical behaviour of recasting Ni–Cr and Co–Cr non-precious dental alloys. Corros Sci. 2004;46:2825–36. https://doi.org/10.1016/j.corsci.2004.03.011.
• [43] Walczak M, Drozd K. Effects of recasting of CoCrMoW dental alloy on its microstructure and corrosion resistance. Curr Issues Pharm Med Sci. 2013;36:425–9. https://doi.org/10.12923/j.2084-980X/26.4/a.17.
• [44] Song D, Ma AB, Jiang JH, Lin PH, Yang DH, Fan JF. Corrosion behaviour of bulk ultra-fine grained AZ91D magnesium alloy fabricated by equal-channel angular pressing. Corros Sci. 2011;53:362–73. https://doi.org/10.1016/j.corsci.2010.09.044.
• [45] Wu S, Wang S, Wang G, Yu X, Liu W, Chang Z, Wen D. Microstructure, mechanical and corrosion properties of magnesium alloy bone plate treated by high-energy shot peening. Trans Non-ferr Metals Soc China. 2019;29:1641–52. https://doi.org/10.1016/S1003-6326(19)65071-5.
• [46] Aung NN, Zhou W. Effect of grain size and twins on corrosion behaviour of AZ31B magnesium alloy. Corros Sci. 2010;52:589–94. https://doi.org/10.1016/j.corsci.2009.10.018.
• [47] Opt-Hoog C, Birbilis N, Estrin Y. Corrosion of pure Mg as a function of grain size and processing route. Adv Eng Mater. 2008;10:579–82. https://doi.org/10.1002/adem.200800046.
• [48] Qiao M, Hu J, Guo K, Wang Q. Influence of shot peening on corrosion behavior of low alloy steel. Mater Res Express. 2020;7:016574. https://doi.org/10.1088/2053-1591/ab6920.

Uwagi

PL

Opracowanie rekordu ze środków MEiN, umowa nr SONP/SP/546092/2022 w ramach programu "Społeczna odpowiedzialność nauki" - moduł: Popularyzacja nauki i promocja sportu (2022-2023)