Erosion Wear Characteristics of Novel AMMC Produced Using Powder Metallurgy

• Autorzy: Behera Rajesh Kumar , Samal Birajendu Prasad , Panigrahi Sarat Chandra , Parida Pramod Kumar , Muduli Kamalakanta , Muhammad Noor , Das Nitaisundar , Abd Rahim Shayfull Zamree

Identyfikatory

DOI

10.24425/amm.2022.139697

• Języki publikacji: EN

Abstrakty

EN

Currently, the world of material requires intensive research to discover a new-class of materials those posses the properties like lower in weight, greater in strength and better in mechanical properties. This led to the study of light and strong alloys or composites. This study focuses to produce current novel aluminium composite with an appreciable density, good machinable characteristics, less corrosive, high strength, light weight and low manufacturing cost product. In this research, an aluminium metal matrix composites (AMMC) (Al-0.5Si-0.5Mg-2.5Cu-15SiC) was developed using the metallurgical powdered method and subjected to the investigation of erosion wear characteristics. Here the solid particle erosion test was conducted on AMMC samples. The article presents, the design of Taguchi experiments and statistical techniques of erosion wear characteristics and the behaviors of the composite. The rate of erosion wear found to decrease with increasing impact angle, regardless of the rate of impact. With higher impact velocity erosion rate increases but decreases with stand of distance.

Słowa kluczowe

EN

AMMC; powder metallurgy; microstructure; wear behavior; particle erosion; Taguchi technique

• Wydawca: Institute of Metallurgy and Materials Science of Polish Academy of Sciences ; Committee of Materials Engineering and Metallurgy of Polish Academy of Sciences
• Czasopismo: Archives of Metallurgy and Materials
• Rocznik: 2022
• Tom: Vol. 67, iss. 3
• Strony: 1027--1032
• Opis fizyczny: Bibliogr. 28 poz., fot., rys., tab., wykr.

Twórcy

autor

Behera Rajesh Kumar

• Biju Patnaik University of Technology, Odisha, India

• https://orcid.org/0000-0002-3017-8585

autor

Samal Birajendu Prasad

• Orissa Engineering College, Department of Mechanical Engineering, Bhubaneswar, Odisha, India

• https://orcid.org/0000-0003-2338-6703

autor

Panigrahi Sarat Chandra

• Raajdhani Engineering College, Bhubaneswar, India

• https://orcid.org/0000-0002-8908-8357

autor

Parida Pramod Kumar

• College Engineering and Technology, Department of Mechanical Engineering Bhubaneswar, Odisha, India

• https://orcid.org/0000-0001-8619-8924

autor

Muduli Kamalakanta

• Papua New Guinea University of Technology, Department of Mechanical Engineering, Lae, Morobe Province, Pmb 411, Papua New Guinea
• C.V. Raman Global University, Bhubaneswar, Odisha, India

• https://orcid.org/0000-0002-4245-9149

autor

Muhammad Noor

• Universiti Malaysia Perlis, Center of Excellence Geopolymer & Green Technology (Cegeogtech) and Faculty of Mechanical Engineering Technology, Kampus Pauh Putra, 02600 Arau, Perlis, Malaysia

• https://orcid.org/0000-0002-0998-0602

autor

Das Nitaisundar

• C.V. Raman Global University, Bhubaneswar, Odisha, India

autor

Abd Rahim Shayfull Zamree

• Universiti Malaysia Perlis, Center of Excellence Geopolymer & Green Technology (Cegeogtech) and Faculty of Mechanical Engineering Technology, Kampus Pauh Putra, 02600 Arau, Perlis, Malaysia

• https://orcid.org/0000-0002-1458-9157

Bibliografia

• [1] R.K. Behera, B.P. Samal, S.C. Panigrahi, et al., A Novel Aluminum Metal Matrix Composite Produced By Powder Metallurgy Method’, Indian Patent Journal 49, 60597 (2020).
• [2] R.K. Behera, B.P. Samal, S.C. Panigrahi, S.R. Das, Optimization of erosion wears of Al-Mg-Si-Cu-SiC composite produced by the PM method, Corros. Rev. 39 (1), 63-75 (2020). DOI: https://doi.org/10.1515/corrrev-2020-0048
• [3] R.K. Behera, B.P. Samal, S.C. Panigrahi, Manufacture of die and their designing parameters for sintered AMC product, Matériaux & Techniques 107 (6), 605, (1-7) (2019). DOI: https://doi.org/10.1051/mattech/2020009
• [4] A.V. Sandu, M.S. Baltatu, M. Nabialek, A. Savin, P. Vizureanu, Characterization and Mechanical Proprieties of New TiMo Alloys Used for Medical Applications, Materials 2973, (1-10) (2019).
• [5] R.K. Behera, S.C. Panigrah, B.P. Samal, P.K. Parida, Mechanical Properties and Micro-Structural Study of Sintered Aluminium Metal Matrix Composites by P/M Technique, Journal of Modern Manufacturing Systems and Technology 3 (2), 089-097 (2019). DOI: https://doi.org/10.1016/j.eng.2018.07.020
• [6] M. Nabialek, Influence of the Quenching Rate on the Structure and Magnetic Properties of the Fe-Based Amorphous Alloy, Arch. Metall. Mater. 61 (1), 439-444 (2016).
• [7] R.K. Behera, B.P. Samal, S.C. Panigrahi, K.K. Muduli, Microstructural and Mechanical Analysis of Sintered Powdered Aluminium Composites, Adv. Mater. Sci. Eng. 2020, Article ID 1893475, 1-7 (2020). DOI: https://doi.org/10.1155/2020/1893475
• [8] R.K. Behera, B.P. Samal, S.C. Panigrahi, Investigations into dry-sliding wear behaviour of a novel composite (aluminium-magnesium-siliconcopper-silicon carbide) produced by powder-metallurgy route, Materialwiss. Werkstofftech 52 (3), 320-331 (2021). DOI: https://doi.org/10.1002/mawe.202000140
• [9] N. Radhika, Mechanical properties and abrasive wear behavior of Functionally Graded Al-Si12Cu/Al2O3 Metal Matrix Composite, Trans. Indian. Inst. Met. 70 (1), 145-157 (2017).
• [10] M.K. Surappa, Aluminum matrix composites: Challenges and opportunities, Sadhana February/April 28 (1&2), 319-334 (2003).
• [11] R.K. Behera, B.P. Samal, S.C. Panigrahi, et al., Evaluation of magnesium recovery in Al-Mg alloys produced by modified stir casting method using genetic algorithm optimisation technique, Int. J. Materials Engineering Innovation 12 (2), 134-148 (2021). DOI: https://doi.org/10.1504/IJMATEI.2021.115605
• [12] Y. Sahin, The prediction of wear resistance model for the metal matrix composites, Wear 25, 1717-1722 (2005).
• [13] B.P. Samal, A.K. Misra, S.C. Panigrahi, et al., A novel technique for improved recovery of Mg-analysis of the microstructure and physical properties, J. Mater. Metal. Eng. 3 (1), 1-7 (2013).
• [14] R. Rattan, J. Bijwe, Influence of impingement angle on solid particle erosion of carbon fabric reinforced polyetherimide composite, Wear 262 (5-6), 568-574 (2007).
• [15] K. Gruszka, M. Nabiałek, M. Szota, K. Bloch, J. Gondro, P. Pietrusiewicz, A.V. Sandu, A.M. Mustafa, Al Bakri, S. Walters, K. Walters, S. Garus, M. Dośpiał, J. Mizera, Analysis of the Thermal and Magnetic Properties of Amorphous Fe61Co10Zr2.5Hf2.5Me2W2B20 (where Me = Mo, Nb, Ni OR Y) Ribbons, Arch. Metall. Mater. 61 (2), 641-644 (2016).
• [16] T. Ibrahim, A mechanism for solid particle erosion in ductile and brittle materials, MS Thesis, Wichita State University (1990).
• [17] K.V. Pool, C.K.H. Dharan, I. Finnie, Erosion wear of composite materials, Wear 107 (1), 1-12 (1986).
• [18] B.K. Prasad, Investigation into sliding wear performance of zinc-based alloy reinforced with SiC particles in dry and lubricated conditions, Wear 262, 262-273 (2007).
• [19] A.V. Sandu, M.S. Baltatu, M. Nabialek, A. Savin, P. Vizureanu, Characterization and mechanical proprieties of new TiMo alloys used for medical applications, Materials 12 (18), 2973 (2019). 1032
• [20] R. PäiviKivikytö, Correlation of material characteristics and wear of powder metallurgical metal matrix composites, Doctoral Theses in Materials and Earth Sciences, Helsinki University of Technology, Laboratory of Materials Science, Espoo (2006).
• [21] S.K. Acharya, V. Dikshit, P. Mishra, Erosive wear behaviour of redmud filled metal matrix composite, J. Reinf. Plast. Compos. 27 (2), 145 (2008).
• [22] M.G. Nabiałek, M.J. Dośpiał, M. Szota, P. Pietrusiewicz, J. Jędryka, Investigation of the thermal and magnetic properties of Fe61Co10 Zr2Fe61Co10Zr2.5Hf2.5Me2W2B20 (Me=Y, Nb, W, Ti, Mo, Ni) bulk amorphous alloys obtained by an induction suction method, Journal of Alloys and Compounds 509 (7), 3382-3386 (2011).
• [23] S.C. Mishra, S. Das, A. Satapathy, P.V. Ananthapadmanabhan, K.P. Sreekumar, Erosion wear analysis of plasma sprayed ceramic coating using the Taguchi technique, Tribo. l Trans. 52, 401-404 (2009).
• [24] S. Basavarajappa, G. Chandramohan, J.P. Davim, Application of Taguchi techniques to study dry sliding wear behaviour of metal matrix composites, Mater. Des. 28, 1393-1398 (2007).
• [25] M.P. Thomas, J.E. King, Effect of thermal and mechanical processing on tensile properties of powder formed 2124 aluminium and 2124 Al-SiC p metal matrix composite. Mater. Sci. Technol. 9 (9), 742-753 (1993).
• [26] L.H. Hihara, R.M. Latanision, Corrosion of metal matrix composites, Int. Mater. Rev. 39 (6), 245-264 (1994).
• [27] V.B. Nguyen, Q.B. Nguyen, Y.W. Zhang, C.Y.H. Lim, B.C. Khoo, Effect of particle size on erosion characteristics, Wear 348, 126-137 (2016).
• [28] G.P. Kumar, R. Keshavamurthy, P. Kumari, C. Dubey, Corrosion behaviour of TiB2 reinforced aluminium based in situ metal matrix composites, Perspect. Sci. 8, 172-175 (2016).

Uwagi

1. The authors acknowledge Orissa Engineering College and College of Engineering Technology, Bhubaneswar, India for it’s laboratory experiments.

2. Opracowanie rekordu ze środków MNiSW, umowa nr SONP/SP/546092/2022 w ramach programu "Społeczna odpowiedzialność nauki" - moduł: Popularyzacja nauki i promocja sportu (2024).