Influence of dry grinding on physicochemical and surface properties of talc

• Autorzy: Arsoy Z. , Ersoy B. , Evcin A. , Icduygu M. G.

Identyfikatory

DOI

10.5277/ppmp170124

• Języki publikacji: EN

Abstrakty

EN

In this study the effect of dry grinding on hydrophobicity, surface free energy (SFE), particle size distribution, surface area, porosity, oil absorption, and whiteness of talc was investigated. The dry grinding was performed in a vibrating ball mill at various grinding times (5-150 min) by keeping the grinding parameters constant such as the number of ball, ball size, the amount of talc, vibration frequency and amplitude. Then, the contact angle measurements were performed on disc-shaped samples produced under a hydraulic press by using a sessile drop method with different liquids (water, formamide, diiodomethane, and ethylene glycol), and surface free energies (mJ/m2) were calculated according to OCG-AB (van Oss-Chaudhury-Good Acid-Base) method by using the obtained contact angle values. In addition, the physicochemical analyses given above were carried out for each ground sample. According to the obtained results, the water contact angle and SFE of the original sample were 63.800 and 48.70 mJ/m2, respectively. The lowest and highest contact angle values for the samples were obtained as 59.300 and 70.770 at grinding times for 5 and 15 min, respectively. It was also determined that the grinding time over 30 min showed no significant effect on the contact angle and SFE values of the samples. Similarly, the grinding time vs. SFE, and the grinding time vs. contact angle curves showed a similar trend. Parallel to the increase in the surface area upon the grinding, a small increase in the oil absorption and whiteness of talc was also determined.

Słowa kluczowe

EN

talc; grinding; contact angle; surface free energy; oil absorption; whiteness

• Wydawca: Oficyna Wydawnicza Politechniki Wrocławskiej
• Czasopismo: Physicochemical Problems of Mineral Processing
• Rocznik: 2017
• Tom: Vol. 53, iss. 1
• Strony: 288--306
• Opis fizyczny: Bibliogr. 62 poz., rys., tab.

Twórcy

autor

Arsoy Z.

• Afyon Kocatepe University, Department of Mining Engineering, 03200 Afyonkarahisar, Turkey

autor

Ersoy B.

• Afyon Kocatepe University, Department of Mining Engineering, 03200 Afyonkarahisar, Turkey

autor

Evcin A.

• Afyon Kocatepe University, Department of Materials Science & Engineering, 03200 Afyonkarahisar, Turkey

autor

Icduygu M. G.

• Giresun University, School of Civil Aviation, 28200 Giresun, Turkey

Bibliografia

• AGATZINI-LEONARDOU S., TSAKIRIDIS P.E., OUSTADAKIS P., KARIDAKIS T. and KATSIAPI A. 2009, Hydrometallurgical process for the separation and recovery of nickel from sulphate heap leach liquor of nickeliferrous laterite ores, Minerals Engineering 22, 1181–1192.
• AGLIETTI E.F., 1994, The effect of dry grinding on the structure of talc, Applied Clay Science, 9, 139-147.
• ANDRES K. and HAUDE F., 2010, Application of the Palla™ vibrating mill in ultrafine grinding circuits, The Journal of The Southern African Institute of Mining and Metallurgy, 110, 125-131.
• ARSOY Z., 2013, Adacal Industrial Minerals Co., Research and Development responsible, Research and Development Study Report, 30 p.
• ARSOY Z., 2014, The Effects of grinding on surface properties of talc (in Turkish), Afyon Kocatepe University, Institute of Natural and Applied Science, MS Thesis, p. 101.
• BALEK V., PEREZ-MAQUEDA L.A., POYATO J., CERNY Z., RAMIREZ-VALLE V., BUNTSEVA I.M. and PEREZ-RODRIGUEZ J.L., 2007, Effect of grinding on thermal reactivity of ceramic clay minerals, Journal of Thermal Analysis and Calorimetry, 88(1), 87-91. BHASIN A., MASAD E., LITTLE D. and LYTTON R., 2006, Limits on adhesive bond energy for improved resistance of hot-mix asphalt to moisture damage, Transp. Res. Rec. J.Transp. Res. Board, 1970(1), 3-13.
• BILLMEYER F.W. and SALTZMAN M., 1981, Principles of Color Technology, Wiley Interscience, New York.
• BILGIN O, 2009, Investigation of raw material properties of Gordes zeolites and usability in various industries (in Turkish), Afyon Kocatepe, Institute of Natural and Applied Science, PhD Thesis .
• BIZI M., FLAMENT M.P., LETERME PLANNING., BAUDET G. and GAYOT A., 2003, Relation between structural characteristics of talc and its properties as an antisticking agent in the production of tablets, European Journal of Pharmaeceutical Sciences, 19, 373-379.
• CAWOOD S.R., HARRIS P.J. and BRADSHAW D.J., 2005, A simple method for establishing whether the adsorption of polysaccharides on talc is a reversible process, Minerals Engineering, 18(10), 1060-1063.
• CHIEM L., HUYNH L., RALSTON J., and BEATTIE, D., 2006, An in situ ATR-FTIR study of polyacrylamide adsorption at the talc surface, Journal of Colloid and Interface Science, 297, 54-61. COURARD L., MICHEL F. and MARTIN M., 2011, The evaluation of the surface free energy of liquids and solids in concrete technology, Construction and Building Materials, 25, 260-266.
• DELLISANTI F., VALDRE G. and MONDONICO M., 2009, Changes of the main physical and technological properties of talc due to mechanical strain, Applied Clay Science, 42, 398-404.
• DIN EN ISO 787-5. General Methods of Test For Pigments and Extenders – Part 5: Determination of Oil Absorption Value (ISO 787-5:1980); German Version EN ISO 787-5:1995.
• DRZYMALA J., 1994, Hydrophobicity and collectorless flotation of inorganic materials, Advances in Colloids and Interface Science, 50, 143-185.
• ERSOY B., 2011, Influence of pH and chloride-based metal salts on coagulation/dispersion behavior of talc suspension, Separation Science and Technology, 46, 1519–1527.
• ERSOY B., DIKMEN S., YILDIZ A., GOREN R. and ELITOK O., 2013, Mineralogical and physicochemical properties of talc from Emirdag, Afyonkarahisar, Turkey, Turkish Journal of Earth Sciences, 22: 632-644.
• FENG J., NGUYEN S.T., FAN Z., DUONG H.M., 2015, Advanced fabrication and oil absorption properties of super-hydrophobic recycled cellulose aerogels, Chemical Engineering Journal, 270 (2015) 168-175.
• FILIO M.J., SUGIYAMA K., KASAI E. and SAITO F., 1993, Effect of dry mixed grinding of talc kaolinite and gibbsite on preparation of cordierite ceramics, JCEJ, 26, 565-569.
• FOSTER J and DOLL J., 2004, Particle size effect on talc lubricant activity, American Association of Pharmaceutical Scientists 2004 annual Meeting Poster Session, 18 p.
• FOWKES F.M., 1964, Attractive forces at interfaces, Industrial and Engineering Chemistry, 56(12), 40-52.
• FOWKES F.M., 1983, Acid–base interactions in polymer adhesion: Physicochemical aspects of Polymer Surfaces, Ed: K.L. Mital, Plenum Press, New York.
• FOWKES F.M., 1972, Donor—acceptor interactions at interfaces, J. of Adhesion, 4, 155.
• GAMIZ E., MELGOSAB M., SANCHEZ-MARANON M., MARTIN M.J.M. and DELGADOA R., 2005, Relationships between chemico-mineralogical composition and color properties in selected natural and calcined Spanish kaolins, Applied Clay Science, 28, 269-282.
• GOOD R.J. and VAN OSS, C.J., 1992, In Modern Approaches to Wettability: Theory and Applications, Eds: M. E. Schrader, and G. Loeb, Plenum Press, New York, pp. 1-27.
• GOREN R., GOCMEZ H., OZGUR C., 2006, Synthesis of cordierite powder from talc, diatomite and alumina, Ceramics International, 32, 407-409.
• GRIM R., 1968, Clay mineralogy, McGraw-Hill Book Company, New York, 596.
• HOLLAND H.J. and MURTAGH M.J., 2000, An XRD morphology index for talcs: The effect of particle size and morphology an the specific surface area, International Center for Diffraction Data 2000, Advances in X-ray Analysis, 42, 421-429 p.
• IMIFABI, Talc HTP2, Technical Data Sheet, 2013.
• KANO J. and SAITO F., 1998, Correlation of powder characteristics of talc during Planetary Ball Milling with the impact energy of the balls simulated by the Particle Element Method, Powder Technology, 98, 166-170.
• KOLLURI O.S., 1994, Plasma Surface Engineering of Plastics, ASM Handbook, Vol. 5, Surface Engineering, ASM International, USA.
• LEFEBVRE G., GALET L. and CHAMAYOU, A., 2011, Dry coating of talc particles with fumed silica: Influence of the silica concentration on the wettability and dispersibility of the composite particles, Powder Technology, 208, 372–377.
• LEJA J, 1982, Surface Chemistry of Froth Flotation, Plenum Pres (Second Edition).
• LIAO J. and SENNA M., 1992, Thermal behavior of mechanically amorphized talc, ThermochimicaActa, 197, 295-306.
• LIU G., FENG Q., OU L., LU Y. and ZHANG G., 2006, Adsorption of polysaccharide onto talc, Minerals Engineering, 19, 147–153.
• LOPEZ-GALINDO A. and VISERAS C., 2004, Pharmaceutical and cosmetic applications of clay, Interface Science and Technology: Clay Surfaces, F.Wypych, K. G. Satyanarayana (Eds.), 1, 267-289.
• MARTIN P.J., WILSON D.I. and BONNETT P.E. 2004, Rheological study of a talc-based paste for extrusion-granulation, Journal of the European Ceramic Society, 24(10-11), 3155-3168.
• MEIRON T.S., MARMUR A. and SAGUY I.S., 2004, Contact angle measurement on rough surfaces, Journal of Colloid and Interface Science, 274, 637-644.
• NETO J.B.R. and MORENO R., 2007, Rheological behaviour of kaolin/talc/alumina suspensions for manufacturing cordierite foams, Applied Clay Science, 3(1-2), 157-166.
• NKOUMBOU C., VILLIERAS F., NJOPWOUO D., NGOUNE C., BARRES O., PELLETIER M., RAZAFITIANAMAHARAVO A. and YVON J., 2008, Physicochemical properties of talc ore from three deposits of Lamal Pougue area (Yaounde Pan-African Belt, Cameroon), in relation to industrial uses, Applied Clay Science, 41, 113–132.
• PEREZ-RODRIQUEZ J.L. and SANCHEZ-SOTO P.J., 1991), The influence of the dry grinding on the thermal behaviour of pyrophyllite, Journal of Thermal Analysis, 37, 1401-1413.
• PENG L., YUAN S., YAN G., YU P., LUO Y., 2014, Hydrophobic sponge for spilled oil absorption, J. APPL. POLYM. SCI., 131(20), 15.
• RALPH D. and NELSON J.R., 1988, Dispersing powders in liquids, 245 p., Delaware, U.S.A.
• SANCHEZ-SOTO P.J., WIEWIORA A., AVILES M.A., JUSTO A., PEREZ-MAQUEDA L.A., PEREZ-RODRIGUEZ J.L., BYLINA P., 1997, Talc from Puebla de Lillo, Spain. II. Effect of dry grinding on particle size and shape, Applied Clay Science, 12, 297-312.
• SATO T. and RUCH R., 1980, Stabilization of Colloidal Dispersions by Polymer Adsorption, 155 p., New-York.
• SHEN W., FILONANKO Y., TRUONG Y., PARKER I.H., BRACK N., PIGRAM P. and LIESEGANG J., 2000, Contact angle measurement and surface energetic of sized and unsized paper, Colloids and Surfaces A: Physicochemical and Engineering Aspects, 173, 117-126.
• SORIANO M., SANCHEZ-MARANON M., MELGOSA M., GAMIZ E. & DELGADO R., 2002, Influence of chemical and mineralogical composition on colour for commercial talcs, Color Research and Application, 27, 430–440.
• STEIN J., 2005, Ultrafine dry grinding with media mills, Post Script Bild Phpylogo Kleineps, 17(6), 1-6.
• TEMUUJIN J., OKADA K., JADAMBAA T.S., MAC KENZIA K.J.D. and AMARSANAA J., 2003, Effect of grinding on the leaching behaviour of pyrophyllite, Journal of the European Ceramic Society, 23, 1277-1282.
• TERADA K. and YONEMOCHI E., 2004, Physicochemical properties and surface free energy of ground talc, Solid State Ionics, 172, 459-462.
• TOMAINO G.P., 2000, Talc and pyrophyllite, Mining Engineering, 64-65.
• TS 10521, December 1992. Talc-used in paper industry, Turkish Standard Institute, Ankara (in Turkish).
• ULUSOY U., 2008, Application of Anova to image analysis results of talc particles produced by different milling, Powder Technology, 188, 133-138.
• VAN OLPHEN H., 1977, Clay Colloid Chemistry (second edition), John Wiley & Sons Inc., New York, 318 p.
• WALLQVIST V., CLAESSON P.M., SWERIN A., SCHOELKOPF J. and GANE P.A.C., 2009, Influence of wetting and dispersing agents on the interaction between talc and hydrophobic particles, Langmuir, 25(12), 6909–6915.
• WANG J. and SOMASUNDARAN P., 2005, Adsorption and conformation of carboxymethylcellulose at solid-liquid interfaces using spectroscopic, AFM and allied techniques, Journal of Colloid and Interface Science, 291, 75-83.
• WU W., GIESSE, R.F., Jr. and VAN OSS C.J., 1996, Change in surface properties of solids caused by grinding, Powder Technology, 89, 129-132.
• YEKELER M., ULUSOY U. and HICYILMAZ C., 2004, Effect of particle shape and roughness of talc mineral ground by different mills on the wettability and floatability, Powder Technology, 140, 68-78.
• YILDIRIM I., 2001, Surfaces free energy characterization of powders’, Doctor of Philosophy In Mining and Minerals Engineering, Faculty of the Virginia Polytechnic Institute and State University. Blacksburg, Virginia, USA.
• YOON R.H. and YORDAN J.L., 1991, The critical rupture thickness of thin water films on hydrophobic surfaces, J. of Colloid and Interface Science,146,(2), pp. 101-108.
• YANG H., DU C., HU Y., JIN S. YANG W., TANG A., AVVAKUMOV E.G., 2006, Preparation of porous material from talc by mechanochemical treatment and subsequent leaching, Applied Clay Science, 31, 290-297.
• ZBIK M., SMART R., ST. C., (2005), Influence of dry grinding on talc and kaolinite morphology: inhibition of nano-bubble formation and improved dispersion, Minerals Engineering, 18, 969-976.
• ZENKIEWICZ M., 2007, Methods for the calculation of surface free energy of solids, Journal of Achievements in Materials and Manufacturing Engineering, 24, 137-146.