Flexural strengthening of reinforced concrete beams using carbon fiber reinforced polymer rope with additional anchorage to limit debonding

• Autorzy: Tworzewski Paweł , Bacharz Kamil

Identyfikatory

DOI

10.12913/22998624/194607

• Języki publikacji: EN

Abstrakty

EN

The use of CFRP rope as NSM flexural strengthening and at the same time a method of limiting its debonding by anchoring its ends in drilled holes has been described. The work examined the effectiveness of strengthening reinforced concrete beams using NSM CFRP ropes and compared the solution with the traditional one using NSM CFRP strips. The study included 14 elements, including: 3 unstrengthened beams, 5 beams strengthened with NSM CFRP ropes and 6 beams strengthened with NSM CFRP strips. All beams were loaded monotonically until failure with two concentrated forces (four-point loading testing). The measurements were carried out using digital image correlation (DIC). In order to limit the possibility of debonding, in selected beams an anchorage made of CFRP rope glued into previously drilled holes in the beam web at an angle of 90o (6 beams) and in the case of using two CFRP ropes, at an angle of 45o and 90o (2 beams) was used. The analysis included a comparison of: failure modes, load–deflection responses and strain distributions. The obtained value of strengthening efficiency was: with the use of a single rope 25-30%, with the use of two ropes 46 and 49%, for CFRP strip 31-36%. In the case of beams strengthened with CFRP rope, debonding did not occur. In all beams strengthened with CFRP strips, debonding occurred and the additional anchoring did not contribute to the delay of its occurrence. All beams reinforced with CFRP rope achieved higher load-bearing capacity than expected and in no case failed due to debonding, which means that the assumed objectives of the work were met.

Słowa kluczowe

EN

debonding; flexural strengthening; CFRP rope; concrete; near-surface mounted; NSM

• Wydawca: Lublin University of Technology ; Polish Society of Ecological Engineering (PTIE), Branch of PTIE in Lublin
• Czasopismo: Advances in Science and Technology. Research Journal
• Rocznik: 2025
• Tom: Vol. 19, no. 1
• Strony: 72--87
• Opis fizyczny: Bibliogr. 43 poz., fig., tab.

Twórcy

autor

Tworzewski Paweł

• Department of Building Structures, Kielce University of Technology, Al. Tysiąclecia Państwa Polskiego 7, 25-314 Kielce, Poland

• https://orcid.org/0000-0002-2677-2899

autor

Bacharz Kamil

• Department of Strength of Materials and Structures Diagnostics, Kielce University of Technology, Al. Tysiąclecia Państwa Polskiego 7, 25-314 Kielce, Poland

• https://orcid.org/0000-0002-6626-6202

Bibliografia

• 1. Linek M., Nita P., Wolka P., Żebrowski W., Application of Natural Mineral Additives in Construction, IOP Conference Series: Earth and Environmental Science, 2017, 95, https://doi.org/10.1088/1755-1315/95/2/022006
• 2. Raczkiewicz W., Bacharz M., Bacharz K, Michał T., Reinforcement corrosion testing in concrete and fiber reinforced concrete specimens exposed to aggressive external factors. Materials, 2023, 16, 3, 1-19, https://doi.org/10.3390/ma16031174
• 3. Bacharz M., Bacharz K., Trąmpczyński W., The Correlation between Shrinkage and Acoustic Emission Signals in Early Age Concrete. Materials. 2022, 15, 15, 5389, https://doi.org/10.3390/ma15155389
• 4. Goszczyńska B., Świt G., Trąmpczyński W., Tworzewska J., Tworzewski P., Zastosowanie metody emisji akustycznej do analizy procesu zarysowania belek żelbetowych. Zeszyty Naukowe Politechniki Rzeszowskiej, Seria: Budownictwo i Inżynieria Środowiska. 2012, 59, 3/II, 77–84.
• 5. Tworzewski P., Alexy J.K., Barnes R.W. Intermediate crack debonding of externally bonded FRP reinforcement – comparison of methods. Materials 2022, 15, 7390. https://doi.org/10.3390/ma15207390
• 6. Ye L.P., Lu X.Z., Chen J.F. Design proposals for the debonding strengths of FRP strengthened RC beams in the chinese design code. In Proceedings of the International Symposium on Bond Behaviour of FRP in Structures, Hong Kong, China, 7–9 December 2005, 45–54.
• 7. Said H., Wu Z. Evaluating and proposing models of predicting IC debonding failure. Journal of Composites for Construction. 2008, 12, 3, 284–299. https://doi.org/10.1061/(ASCE)1090-0268(2008)12:3(284)
• 8. Taljsten B. Concrete beams strengthened for bending using CFRP-sheets. In Proceedings of 8th International Conference on Advanced Composites for Concrete Repair, Engineering Technics Press, London, England, 1999.
• 9. Liu I., Oehlers D.J., Seracino R. Parametric study of intermediate crack IC debonding on adhesively plated beams. In Proceedings of FRP Composites in Civil Engineering, London, England, 2004, 515–521.
• 10. Sharif A., Al-Solaimani G.J., Basunbul I.A., Balauch, M.H., Ghaleb B.N. Strengthening of initially loaded reinforced concrete beams using FRP plates. ACI Structural Journal. 1994, 91, 2, 160–168. https://doi.org/10.14359/4594
• 11. Ritchie P.A., Thomas D.A., Lu L.W., Connely G.M. External reinforcement of concrete beams using fiber reinforced plastics. ACI Structural Journal. 1999, 88, 4, 490–500.
• 12. Nguyen D.M., Chan T.K., Cheong H.K. Brittle failure and bond development length of CFRP— Concrete beams. Journal of Composites for Construction, 2001, 5, 1, 12–17. https://doi.org/10.1061/(ASCE)1090-0268(2001)5:1(12)
• 13. International Federation for Structural Concrete (FIB). Externally Bonded FRP Reinforcement for RC Structures. Bulletin 14; International Federation for Structural Concrete (FIB): Lausanne, Switzerland, 2001.
• 14. Tworzewski P., Bacharz K., Michałowska-Maziejuk D. Anchorage Systems in FRP-Strengthened Reinforced Concrete. JCEEA, 2018, 65, 101–110. http://dx.doi.org/10.7862/rb.2018.47 [14]
• 15. Alobaidi H.E., Al-Zuhairi A.H., Structural strengthening of insufficiently designed reinforced concrete T-beams using CFRP composites. Civil Engineering Journal. 2023, 5, 8, 1880–1896, https://doi.org/10.28991/CEJ-2023-09-08-05
• 16. Balamuralikrishnan R., Al-Mawaali A.S.H., Al-Yaarubi M.Y.Y., Al-Mukhaini B.B., Kaleem A., Seismic upgradation of RC beams strengthened with externally bonded spent catalyst based ferrocement laminates. HighTech and Innovation Journal. 2023, 4, 1, 189–209. https://doi.org/10.28991/HIJ-2023-04-01-013
• 17. Mostofinejad D., Mahmoudabadi E., Grooving as alternative method of surface preparation to postpone debonding of FRP Laminates in concrete beams. Journal of Composites for Construction. 2010, 14, 6, 804–811, https://doi.org/10.1061/(ASCE)CC.1943-5614.0000117
• 18. Abdallaha M., Al Mahmouda F., Boissièrea R., Abdelouahab K., Mercier J. Experimental study on strengthening of RC beams with Side Near Surface Mounted technique-CFRP bars, Composite Structures. 2020, 234, https://doi.org/10.1016/j.compstruct.2019.111716
• 19. Kotynia R. Przyczepnościowe metody wzmacniania konstrukcji żelbetowych przy użyciu naprężonych kompozytów polimerowych, Przegląd Budowlany, 2015, 7–8, 49–56.
• 20. De Lorenzis L, Teng JG. Near-surface mounted FRP reinforcement: an emerging technique for strengthening structures. Compos Part B: Engineering, 2007, 38, 2, 119–43. https://doi.org/10.1016/j.compositesb.2006.08.003
• 21. Ke1 Y., Zhang S. S., Aff. M., Smith S.T., F., Yu T. Novel Embedded FRP Anchor for RC beams strengthened in flexure with NSM FRP bars: Concept and behavior. Journal of Composites for Construction. 2023, 27, 1, https://doi.org/10.1061/(ASCE)CC.1943-5614.0001279
• 22. Michałowska-Maziejuk D., Goszczyńska B. Effectiveness of strengthening RC beams using composite materials – an accelerated strengthening method; Materials. 2023, 16, 13, https://doi.org/10.3390/ma16134847
• 23. Michałowska-Maziejuk D., Goszczyńska B., Szacowanie nośności belek żelbetowych wzmocnionych kompozytami CFRP, Inżynieria i Budownictwo. 2023, 79, 11–12, 636–643, http://dx.doi.org/10.5604/01.3001.0054.1374
• 24. Hassan T., Rizkalla S. Investigation of bond in concrete structures strengthened with near surface mounted carbon fiber reinforced polymer strips. Journal of Composites for Construction. 2003, 7, 3, 248–257. https://doi.org/10.1061/(ASCE)1090-0268(2003)7:3(248)
• 25. Peng H., Zhang J., Cai C.S., Liu Y., An experimental study on reinforced concrete beams strengthened with prestressed near surface mounted CFRP strips. Engineering Structures. 2014, 79, 15, 222–233. https://doi.org/10.1016/j.engstruct.2014.08.007
• 26. Sharaky I.A., Torres L., Comas J., Barris C. Flexural response of reinforced concrete (RC) beams strengthened with near surface mounted (NSM) fibre reinforced polymer (FRP) bars. Composite Structures. 2014, 109, 1, 8–22 https://doi.org/10.1016/j.compstruct.2013.10.051
• 27. Barros J.A.O., Fortes A.S., Flexural strengthening of concrete beams with CFRP laminates bonded into slits. Cement and Concrete Composites. 2015, 27, 4 471–480. https://doi.org/10.1016/j.cemconcomp.2004.07.004
• 28. Teng, J.G., De Lorenzis L., Wang B., Li R., Wong T.N., Lam L. Debonding failures of RC beams strengthened with near surface mounted CFRP strips. Journal of Composites for Construction. 2006, 10, 2, pp. 92–105, https://doi.org/10.1061/(ASCE)1090-0268(2006)10:2(92)
• 29. Seracino R., Jones N.M., Ali M.S., Page M.W., Oehlers D.J. Bond strength of near-surface mounted FRP strip-to-concrete joints. Journal of Composites for Construction. 2007, 11, 4, 401–409,https://doi.org/10.1061/(ASCE)1090-0268(2007)11:4(401)
• 30. Dias S.J.E., Barros J.A.O., Janwaen W. Behavior of RC beams flexurally strengthened with NSM CFRP laminates. Composite Structures. 2018, 201, 3, 363–376. https://doi.org/10.1016/j.compstruct.2018.05.126
• 31. Fu B., Tang X.T., Li L.J., Liu F., Lin G., Inclined FRP U-jackets for enhancing structural performance of FRP-plated RC beams suffering from IC debonding, Composite Structures. 2018, 200, 15, 36–46, https://doi.org/10.1016/j.compstruct.2018.05.074
• 32. Hosen M., Jumaat M.Z., Islam S. Inclusion of CFRP-epoxy composite for end anchorage in NSMepoxy strengthened beams. Advances in Materials Science and Engineering. 2015, 2015, 1, https://doi.org/10.1155/2015/812797
• 33. Zhang, S.S., Ke Y., Smith S.T., Zhu H.P., Wang Z.L. Effect of FRP U-jackets on the behaviour of RC beams strengthened in flexure with NSM CFRP strips. Composite Structures. 2021, 256 https://doi.org/10.1016/j.compstruct.2020.113095
• 34. Khalifa A, Alkhrdaji T, Nanni A, Lansburg A. Anchorage of surface mounted FRP reinforcement. Concrete International, 1999, ACI, 49–54.
• 35. Kim Y.J., Green M.F., Wight G.R., Prestressed fiber-reinforced polymer (FRP) composites for concrete structures in flexure: fundamentals to applications, Editor(s): Yail J. Kim, Advanced Composites in Bridge Construction and Repair, Woodhead Publishing, 2014, 30-60, https://doi.org/10.1533/9780857097019.1.30
• 36. Smith S.T., Shenghua Hu, Seo Jin Kim, Seracino R. FRP-strengthened RC slabs anchored with FRP anchors. Engineering Structures, 2011. 33, 4, 1075–1087 https://doi.org/10.1016/j.engstruct.2010.11.018
• 37. Haddad, R.H., Harb, A.N., Varying profiles of CFRP ropes for strengthening concrete beams. International Journal of Civil Engineering. 2021, 20, 405–419. https://doi.org/10.1007/s40999-021-00664-2
• 38. Alhilli H.H., Al-Farttoosi M.H., Shear Performance of Reinforced Concrete T Beams Strengthened by Carbon Fiber-Reinforced Polymer Bars. Civil Engineering Journal. 2023, 9, 10, 2411–2429, https://doi.org/10.28991/CEJ-2023-09-10-04
• 39. Adamczak-Bugno A., Lipiec S., Adamczak J., Vičan J., Bahleda F., Identification of destruction processes and assessment of deformations in compressed concrete modified with polypropylene fibers exposed to fire temperatures using acoustic emission signal analysis, numerical analysis, and digital image correlation. Materials. 2023, 16, 6786. https://doi.org/10.3390/ma16206786
• 40. Blikharskyy Y., Kopiika N., Khmil R., Selejdak J., Blikharskyy Z. Review of Development and Application of Digital Image Correlation Method for Study of Stress–Strain State of RC Structures. Applied Sciences. 2022, 12, 19, https://doi.org/10.3390/app121910157
• 41. Bakalarz M.M., Tworzewski P.T., Application of digital image correlation to evaluate strain, stiffness and ductility of full-scale LVL beams strengthened by CFRP. Materials. 2023, 16, 3, 1309, https://doi.org/10.3390/ma16031309
• 42. Szczecina M., Tworzewski P., Bacharz K., Experimental verification of a numerical model of RC beam with CFRP rope strengthening, Computer Assisted Methods in Engineering and Science, 2019, 26, 3–4, 137–151, http://dx.doi.org/10.24423/cames.269
• 43. American Concrete Institute ACI. Guide for the design and construction of externally bonded FRP systems for strengthening concrete structures. ACI 440.2R-17, ACI Committee 440, 2017.