The Effect of Fiber on the Green Strength and Buildability of High-Strength 3D Printing Concrete

• Autorzy: Shahib Al Bari M. , Ekaputri Januarti Jaya
• Języki publikacji: EN

Abstrakty

EN

This paper presents four parameters in 3D Printing Concrete (3DPC) in the fresh state. Flowability, extrudability, open time, and buildability. In addition, this paper also introduces a new method to obtain the green strength of fresh concrete. The high-strength concrete mixture was used as a base mix design. The water to binder ratio and admixture were tuned to obtain the 3DPC that satisfied those four parameters. The 3DPC mix design used cement, silica fume, and reactive powder as a binder with a ratio of 3:1:1. The ratio of sand and binder was 0.9. The water to binder ratio (w/b) was 0.14 with the addition of a superplasticizer and accelerator. To increase the buildability, polyvinyl alcohol (PVA) fiber was added by 0.2% of concrete volume. It had a 30 mm slump, 110 mm flow, 1.1 SRF, 85 minutes of open time, and 7 KPa green strength in 75 minutes. This mix design was able to be printed into 40 layers of 100×400 mm cylinder.

Słowa kluczowe

EN

high-strength concrete; 3D printing; PVA fiber; green strength; shrinkage

• Wydawca: Institute of Metallurgy and Materials Science of Polish Academy of Sciences ; Committee of Materials Engineering and Metallurgy of Polish Academy of Sciences
• Czasopismo: Archives of Metallurgy and Materials
• Rocznik: 2024
• Tom: Vol. 69, iss. 3
• Strony: 839--850
• Opis fizyczny: Bibliogr. 48 poz., fot., rys., tab.

Twórcy

autor

Shahib Al Bari M.

• Department of Civil Engineering, Faculty of Civil, Planning and Geo Engineering, Institut Teknologi Sepuluh Nopember, Surabaya, 60111, Indonesia

• https://orcid.org/0000-0002-4007-9636

autor

Ekaputri Januarti Jaya

• Department of Civil Engineering, Faculty of Civil, Planning and Geo Engineering, Institut Teknologi Sepuluh Nopember, Surabaya, 60111, Indonesia

• https://orcid.org/0000-0002-9547-8132

Bibliografia

• [1] S.C. Paul, G.P.A.G. Van Zijl, I. Gibson, A review of 3D concreto printing systems and materials properties: current status and future research prospects. Rapid Prototyp. J. 24, 4, 784-798 (2018). DOI: https://doi.org/10.1108/rpJ-09-2016-0154
• [2] G.P.A.G. Van Zijl, S.C. Paul, M.J. Tan, Properties of 3D printable concrete. In Proceedings of the International Conference on Progress in Additive Manufacturing Part F1290, 421-426 (2016).
• [3] Y.W.D. Tay, Y. Qian, M.J. Tan, Printability region for 3D concreto printing using slump and slump flow test. Compos. Part B Eng. 174, 106968 (2019). DOI: https://doi.org/10.1016/j.compositesb.2019.106968
• [4] ASTM International, ASTM C1437-15: Standard test Method for Flow of Hydraulic Cement Mortar., pp. 7-8 (2015).
• [5] R.D. Ferron, S. Shah, E. Fuente, C. Negro, Aggregation and breakage kinetics of fresh cement paste. Cem. Concr. Res. 50, 1-10 (2013). DOI: https://doi.org/10.1016/j.cemconres.2013.03.002
• [6] Y. Zhang, Y. Zhang, W. She, L. Yang, G. Liu, Y. Yang, Rheological and harden properties of the high-thixotropy 3D printing concrete. Constr. Build. Mater. 201, 278-285 (2019). DOI: https://doi.org/10.1016/j.conbuildmat.2018.12.061
• [7] T.T. Le, S.A. Austin, S. Lim, R.A. Buswell, A.G.F. Gibb, T. Thorpe, Mix design and fresh properties for high-performance printing concrete. Mater. Struct. Constr. 45, 8, 1221-1232 (2012). DOI: https://doi.org/10.1617/s11527-012-9828-z
• [8] M.G. Wei, W. Li, J. Yang, State-of-the-art of 3D printing technology of cementitious material - An emerging technique for construction. Sci. China Technol. Sci. 60, (2017). DOI: https://doi.org/10.1007/s11431-016-9077-7
• [9] A.V. Rahul, M. Santhanam, H. Meena, Z. Ghani, 3D printable concrete: Mixture design and test methods. Cem. Concr. Compos. 97, 13-23 (2019). DOI: https://doi.org/10.1016/j.cemconcomp.2018.12.014
• [10] B. Panda, M.J. Tan, Experimental study on mix proportion and fresh properties of fly ash based geopolymer for 3D concreto printing. Ceram. Int. 44, 9, 10258-10265 (2018). DOI: https://doi.org/10.1016/j.ceramint.2018.03.031
• [11] F. Özalp, H.D. Yilmaz, Fresh and Hardened Properties of 3D High-Strength Printing Concrete and Its Recent Applications. Iran. J. Sci. Technol. - Trans. Civ. Eng. 44, 319-330 (2020). DOI: https://doi.org/10.1007/s40996-020-00370-4
• [12] A. Kazemian, X. Yuan, E. Cochran, B. Khoshnevis, Cementitious materials for construction-scale 3D printing: Laboratory testing of fresh printing mixture. Constr. Build. Mater. 145, 639-647 (2017). DOI: https://doi.org/10.1016/j.conbuildmat.2017.04.015
• [13] R.J.M. Wolfs, F.P. Bos, T.A.M. Salet, Early age mechanical behaviour of 3D printed concrete: Numerical modelling and experimental testing. Cem. Concr. Res. 106, 103-116 (2018). DOI: https://doi.org/10.1016/j.cemconres.2018.02.001
• [14] J. Ye, C. Cui, J. Yu, K. Yu, J. Xiao, Fresh and anisotropic-mechanical properties of 3D printable ultra-high ductile concrete with crumb rubber. Compos. Part B Eng. 211, No. September 2020, 108639 (2021). DOI: https://doi.org/10.1016/j.compositesb.2021.108639
• [15] H. Alghamdi, S.A.O. Nair, N. Neithalath, Insights into material design, extrusion rheology, and properties of 3D-printable alkali-activated fly ash-based binders. Mater. Des. 167, 107634 (2019). DOI: https://doi.org/10.1016/j.matdes.2019.107634
• [16] N. Gowripalan, P. Shakor, P. Rocker, Pressure exerted on formwork by self-compacting concrete at early ages: A review. Case Stud. Constr. Mater. 15, July, e00642 (2021). DOI: https://doi.org/10.1016/j.cscm.2021.e00642
• [17] N. Banthia, Advances in sprayed concrete (shotcrete), in Developments in the Formulation and Reinforcement of Concrete. Elsevier LTD, pp. 289-306 (2019).
• [18] V.M. de Alencar Monteiro, F. de Andrade Silva, On the design of the fiber reinforced shotcrete applied as primary rock support in the Cuiabá underground mining excavations: A case study. Case Stud. Constr. Mater. 15, no. November (2021). DOI: https://doi.org/10.1016/j.cscm.2021.e00784
• [19] F. Özalp. H.D. Yilmaz, Fresh and Hardened Properties of 3D High-Strength Printing Concrete And Its Recent Applications. Iranian Journal of Science and Technology - Transactions of Civil Engineering (2020). DOI: https://doi.org/10.1007/s40996-020-00370-4
• [20] T.T. Le et al., Hardened properties of high-performance printing concrete. Cem. Concr. Res. 42, 3, 558-566 (2012). DOI: https://doi.org/10.1016/j.cemconres.2011.12.003
• [21] C. Gosselin, R. Duballet, P. Roux, N. Gaudillière, J. Dirrenberger, P. Morel, Large-scale 3D printing of ultra-high performance concrete - a new processing route for architects and builders. Mater. Des. 100, 102-109 (2016). DOI: https://doi.org/10.1016/j.matdes.2016.03.097
• [22] A.D. Agustin, J. J. Ekaputri, Very High Performance Grout (VHPG) for Repairing Materials. Institut Teknologi Sepuluh Nopember (2018).
• [23] V.M. Malhotra, V.S. Ramachandran, R.F. Feldman, P.-C. Aïtcin, Condensed Silica Fume in Concrete. CRC Press (2018).
• [24] G. Vijayakumar, M.H. Vishaliny, D. Govindarajulu, Studies on Glass Powder as Partial Replacement of Cement in Concrete Production. Int. J. Emerg. Technol. Adv. Eng. 3, 2, 153-157 (2013).
• [25] R.U.D. Nassar, P. Soroushian, Strength and durability of recycled aggregate concrete containing milled glass as partial replacement for cement. Constr. Build. Mater. 29, 368-377 (2012). DOI: https://doi.org/10.1016/j.conbuildmat.2011.10.061
• [26] N.A. Soliman, A. Tagnit-Hamou, Development of ultra-high-performance concrete using glass powder - towards ecofriendly concrete. Constr. Build. Mater. 125, 600-612 (2016). DOI: https://doi.org/10.1016/j.conbuildmat.2016.08.073
• [27] K. Wille, A.E. Naaman, S. El-Tawil, G.J. Parra-Montesinos, Ultra-high performance concrete and fiber reinforced concrete: Achieving strength and ductility without heat curing. Mater. Struct. Constr. 45, 309-324 (2012). DOI: https://doi.org/10.1617/s11527-011-9767-0
• [28] M.A. Moghadam, R.A. Izadifard, Experimental investigation on the effect of silica fume and zeolite on mechanical and durability properties of concrete at high temperatures. SN Appl. Sci. 1, 6, 682 (2019). DOI: https://doi.org/10.1007/s42452-019-0739-2
• [29] S. Abbas, M.L. Nehdi, M.A. Saleem, Ultra-High Performance Concrete: Mechanical Performance, Durability, Sustainability and Implementation Challenges. Int. J. Concr. Struct. Mater. 10, 3, 271-295 (2016). DOI: https://doi.org/10.1007/s40069-016-0157-4
• [30] K. Wille, A.E. Naaman, G.J. Parra-Montesinos, Ultra-High Performance Concrete with Compressive Strength Exceeding 150 MPa (22 ksi): A Simpler Way. ACI Mater. J. 108, 1, 46-54 (2011). DOI: https://doi.org/10.14359/51664215
• [31] P.-C. Aïtcin, Water and its role on concrete performance. In Science and Technology of Concrete Admixtures, Elsevier, pp. 75-86 (2016).
• [32] J.J. Ekaputri, K. Maekawa, T. Ishida, Experimental Study on Internal RH of BFS Mortars at Early Age. Mater. Sci. Forum 857, 305-310, May (2016). DOI: https://doi.org/10.4028/www.scientific.net/MSF.857.305
• [33] ACI Committee 209, “ACI Fall 2015 Convention - Creep and Shrinkage in Concrete,” Denver (2015).
• [34] J.J. Ekaputri, T. Ishida, K. Maekawa, Autogeneous Shrinkage of Mortars Made With Different Types of Slag Cement. In Transaction of the Japan Concrete Institute 32, 1, 353-358 (2010).
• [35] F. Hamidi, F. Aslani, Additive manufacturing of cementitious composites: Materials, methods, potentials, and challenges. Constr. Build. Mater. 218, 582-609 (2019). DOI: https://doi.org/10.1016/j.conbuildmat.2019.05.140
• [36] J.J. Ekaputri, S. Junaedi, Wijaya, Effect of Curing Temperature and Fiber on Metakaolin-based Geopolymer. In Procedia Engineering 171, 572-583 (2017). DOI: https://doi.org/10.1016/j.proeng.2017.01.376
• [37] J.J. Ekaputri, C. Fujiyama, N. Chijiwa, T.D. Ho, H T. Nguyen, Improving Geopolymer Characteristics with Addition of Poly-Vinyl Alcohol (PVA ) Fibers. Civ. Eng. Dimens. 23, 1, 28-34 (2021). DOI: https://doi.org/10.9744/CED.23.1.28-34
• [38] J.J. Ekaputri, H. Limantono, Triwulan, T.E.S. Susanto, M.M.A.B. Abdullah, Effect of PVA fiber in increasing mechanical strength on paste containing glass powder. Key Eng. Mater. 673, 83-93 (2016). DOI: https://doi.org/10.4028/www.scientific.net/KEM.673.83
• [39] Z. Malaeb, H. Hachem, A. Tourbah, T. Maalouf, N. El Zarwi, F. Hamzeh, 3D Concrete Printing: Machine and Mix Design. Int. J. Civ. Eng. Technol. 6, 6, 14-22 (2015).
• [40] ASTM International, ASTM C143-15: Standard Test Method for Slump of Hydraulic-Cement Concrete, pp. 1-4 (2015).
• [41] ASTM International, ASTM C230-08:Standard Specification for Flow Table for Use in Tests of Hydraulic Cement. (2008).
• [42] ASTM International, ASTM C403-16: Standard Test Method for Time of Setting of Concrete Mixtures by Penetration Resistance. pp. 1-7 (2016).
• [43] ASTM International, ASTM C496-17: Standard Test Method for Splitting Tensile Strength of Cylindrical Concrete Specimens, pp. 1-5 (2017).
• [44] ASTM International, ASTM C39-20: Standard Test Method for Compressive Strength of Cylindrical Concrete Specimens, pp. 1-8 (2020).
• [45] H. Limantono, J.J. Ekaputri, T.E. Susanto, Effect of silica fume and glass powder on high-strength paste. Key Eng. Mater. 673, 37-46 (2016). DOI: https://doi.org/10.4028/www.scientific.net/KEM.673.37
• [46] H. Du, K.H. Tan, Properties of high volume glass powder concrete. Cem. Concr. Compos. 75, 22-29 (2016). DOI: https://doi.org/10.1016/j.cemconcomp.2016.10.010
• [47] R.J.M. Wolfs, F.P. Bos, T.A.M. Salet, Hardened properties of 3D printed concrete: The influence of process parameters on interlayer adhesion. Cem. Concr. Res. 119, February, 132-140 (2019). DOI: https://doi.org/10.1016/j.cemconres.2019.02.017
• [48] C.A. Juarez, G. Fajardo, S. Monroy, A. Duran-Herrera, P. Valdez, C. Magniont, Comparative study between natural and PVA fibers to reduce plastic shrinkage cracking in cement-based composite. Constr. Build. Mater. 91, 164-170 (2015). DOI: https://doi.org/10.1016/j.conbuildmat.2015.05.028

Uwagi

The research described in this paper was financially supported by the Direktorat Riset, Teknologi, dan Pengabdian Masyarakat (DRPM-ITS), Kementerian Pendidikan, Kebudayaan, Riset dan Teknologi Republik Indonesia [contract number 008/E5/PG.02.00PT/2022 and subontract no. 1513/PKS/ITS/2022]. The authors also gratefully acknowledge financial support from the Institut Teknologi Sepuluh Nopember for this work, under project scheme of the Publication Writing and IPR Incentive Program (PPHKI) 2022. The authors express gratitude to the BASF Indonesia for providing accelerator. We also thank SIKA for providing the silica fume.