Assessment of Tribological Properties of Single- and Double-Layer Pad Coatings Deposited onto Cultivator Points

• Autorzy: Wójcik Wiesław , Barszcz Marcin , Dziedzic Krzysztof , Kuzioła Jarosław , Kowalik Przemysław

Identyfikatory

DOI

10.12913/22998624/111780

• Języki publikacji: EN

Abstrakty

EN

This paper investigates properties of single- and double-layer pad coatings deposited on cultivator points. The coatings were deposited by manual metal arc welding (MMA) with ESAB OK. 84.58 coated electrodes using an inverter welder, DEDRA DESi201. Tribological properties were determined with a THT 1000 tribometer. A ball-on-disc friction pair was used. Experiments were performed in room temperature, with the sliding speed set equal to 0.3 m/s and two loads: 5 and 20 N. In addition, hardness was measured on the surface and in the cross section of samples by a Rockwell hardness test method (scale C). Surface roughness was measured before and after friction, and post-friction surface topography was examined under microscope. Impact strength tests of the coatings with single- and double layers of pads were performed. The tools and IT algorithms were used to collect and process the results of experimental research.

Słowa kluczowe

EN

wear; friction; coatings; welding

PL

zużycie; tarcie; powłoki; spawanie

• Wydawca: Lublin University of Technology ; Polish Society of Ecological Engineering (PTIE), Branch of PTIE in Lublin
• Czasopismo: Advances in Science and Technology. Research Journal
• Rocznik: 2019
• Tom: Vol. 13, no 3
• Strony: 120--128
• Opis fizyczny: Bibliogr. 27 poz., fig., tab.

Twórcy

autor

Wójcik Wiesław

• Lublin University of Technology, Fundamentals of Technology Faculty, Department of Fundamental of Technology, 38 Nadbystrzycka Street, 20-618 Lublin, Poland

autor

Barszcz Marcin

• Lublin University of Technology, Electrical Engineering and Computer Science Faculty, Institute of Computer Science, 36B Nadbystrzycka Street, 20-618 Lublin, Poland

autor

Dziedzic Krzysztof

• Lublin University of Technology, Fundamentals of Technology Faculty, Department of Fundamental of Technology, 38 Nadbystrzycka Street, 20-618 Lublin, Poland

autor

Kuzioła Jarosław

• Lublin University of Technology, Fundamentals of Technology Faculty, Department of Fundamental of Technology, 38 Nadbystrzycka Street, 20-618 Lublin, Poland

autor

Kowalik Przemysław

• Lublin University of Technology, Electrical Engineering and Computer Science Faculty, Institute of Computer Science, 36B Nadbystrzycka Street, 20-618 Lublin, Poland

Bibliografia

• 1. Müller M., Hrabě P., Overlay materials used for increasing lifetime of machine parts working under conditions of intensive abrasion, Research in Agricultural Engineering, 59(1), 2013, 16 22.
• 2. Buchely M.F., Gutierrez J.C., León L.M., Toro A., The effect of microstructure on abrasive wear of hardfacing alloys, Wear, 259, 2005, 52–61.
• 3. Giovanni, S., Friction and Wear, Methodologies for Design and Control, Springer 2015.
• 4. Purkayastha S., Dwivedi D.K., Abrasive and erosive wear performance of rare earth oxide doped Ni/WC coatings, Journal of Tribology, 136(1), 2013, 602–609.
• 5. Lemecha M., Napiórkowski J., Rosiak M., Effect of friction speed on wear intensity in abrasive soil mass, MATEC Web of Conferences, IManE&E 2017, 112, 2017, 6.
• 6. Manuwa S.I., Evaluation of soil/materiali friction and adhesion of akure sandy clay loam soils in southwestern Nigeria, Advances in Natural Science, 5(1), 2012, 41–46.
• 7. Napiórkowski J., Analiza właściwości glebowej masy ściernej w aspekcie oddziaływania zużyciowego, Tribologia, 5, 2010, 53–62.
• 8. Napiórkowski J., Lemecha M., Ligier K., Analiza właściwości tribologicznych napoin z zawartością niobu w glebowej masie ściernej, Tribologia, 3, 2015, 109–120.
• 9. Napiórkowski J., Szczyglak P., Kołakowski K., Analiza geometrii ziaren glebowej masy ściernej, Inżynieria Rolnicza, 4(147), 2013, 237–247.
• 10. Napiórkowski J., Zużyciowe oddziaływanie gleby na elementy robocze narzędzi rolniczych,” Inżynieria Rolnicza, 12 (72), 2005, Rozprawy habilitacyjne nr 17.
• 11. Stabryła J., Starczewski L., Oddziaływanie wodoronośnych składników gleby na zużycie ścierne narzędzi rolniczych, Problemy Eksploatacji, 1, 2006, 199–207.
• 12. Kostencki P., Stawicki T., Temperatura warstwy wierzchniej elementów roboczych narzędzi rolniczych przeznaczonych do uprawy gleby. Części – obiekty badań i warunki ich pracy, kontaktowe pomiary temperatury, Tribologia, 2, 2015, 41–58.
• 13. Kostencki P., Łętkowska B., Nowowiejski R., Polowe badania odporności na zużycie ścierne lemieszy płużnych wykonanych ze stali z dodatkiem boru, Tribologia, 3, 2013, 49–79.
• 14. Napiórkowski J., Pękalski G., Kołakowski K., Badanie struktur i zużywania powłok napawanych w glebowej masie ściernej, Tribologia, 3, 2012, 111–117.
• 15. Napiórkowski J., Ligier K., Lemecha M., Wpływ technologii nanoszenia warstw Fe-C-Cr-B na właściwości zużyciowe w glebowej masie ściernej, Mechanik, 4, 2015, 92–97.
• 16. Barszcz M., Paszeczko M., Lenik K., Self-organization of friction surface of Fe-Mn-C-B coating with increased resistance to abrasion, Archives of Metallurgy and Materials, 60, 2015, 2651–2656.
• 17. Yüksel N., Sahin S., Wear behawior-hardness-microstructure relation of Fe-Cr-C and Fe-Cr-C-B based hardfacing alloys, Materials and Design, 58, 2014, 491–498.
• 18. Gualco A., Svoboda H., Surian E., Study of abrasive wear resistance of Fe-based nanostructured hardfacing, Wear, 360–361, 2016, 14–20.
• 19. Lin C., Chang C., Chen J., Hsieh C., Wu W., Microstructure and wear characteristics of high-carbon Cr-based alloy claddings formed by gas tungsten arc welding (GTAW), Surface & Coatings Technology, 205, 2010, 2590–2596.
• 20. Wang X., Zou Z., Qu S., Microstructure of Fe-Based Alloy Hardfacing Coating Reinforced by TiC-VC Particles, Journal of Iron and Steel Research, 13(4), 2006, 51–55.
• 21. Correa E.O., Alcântara N.G., Valeriano L.C., Barbedo N.D., Chaves R.R., The effect of microstructure on abrasive wear of a Fe-Cr-C-Nb hardfacing alloy deposited by the open arc welding process, Surface & Coatings Technology, 276, 2015, 479–484.
• 22. Pashechko M., Dziedzic K., Barszcz M., Study of the structure and properties of wear-resistant eutectic Fe- Mn-C-B-Si-Ni-Cr coatings, Powder metallurgy and metal ceramics, 52, 2013, 469–476.
• 23. Liu H., Song Z., Cao Q., Chen S., Meng Q., Microstructure and properties of Fe-Cr-C hardfacing alloys reinforced with TiC-NbC, Journal of iron and steel research international, 23(3), 2016, 276–280.
• 24. Pashechko M., Dziedzic K., Barszcz M., Study of coatings obtained from alloy Fe-Mn-C-B-Si-Ni-Cr, Advances in Science and Technology – Research Journal, 31(10), 2016, 194–198.
• 25. Badisch E., Katsich C., Winkelmann H., Franek F., Manish R., Wear behavior of hardfaced Fe-Cr-C alloy and austenitic steel under 2-body and 3-body conditions at elevated temperature, Tribology International, 43, 2010, 1234–1244.
• 26. Bar-Hen M., Etsion I., Experimental study of the effect of coating thickness and substrate roughness on tool wear during turning, Tribology International, 110, 2017, 341–347.
• 27. Kostencki P., Stawicki T., Białobrzeska B., Durability and wear geometry of subsoiler shanks provided with sintered carbide plates, Tribology International, 104, 2016, 19–35.

Uwagi

Opracowanie rekordu w ramach umowy 509/P-DUN/2018 ze środków MNiSW przeznaczonych na działalność upowszechniającą naukę (2019).