A study on electromagnetic transducers for the continuous casting process

• Autorzy: Kim I. S. , Son J. S. , Kim H. J. , Chin B. A.
• Języki publikacji: EN

Abstrakty

EN

Purpose: One of the areas in the continuous casting process that has not been definitively instrumented is a method for reliably locating the part of a continuously cast strand that remains liquid for a period after the outer portion has solidified. Therefore, this paper is focused on the measurement of the solidification point made by a through transmission technique based on the relationship between ultrasonic speed and measured temperature using an EMAT sensor. Design/methodology/approach: An EMAT (Electro Magnetic Acoustic Transducer) has been designed and fabricated with an elongated spiral coil and a permanent magnetic core. Al75×75mm and 75×100mm simulators with 2, 4, 8, 16 and 32 mm holes were produced and demonstrated that the location of the final solidification point during the continuous casting process can be monitored using a 1.0 MHz frequency. Findings: The solidification point in a continuous casting bloom could be detected through a series of tests with the use of a fabricated probe and the amplitude extent of ultrasonic wave decreases as the hole diameter of the simulators increases. Furthermore, through a test of lift-off effect it was found that the extent of amplitude decreases as lift-off increases, thus one of the most important factors for a field application. Research limitations/implications: As cutting speed and cutting length can be predicted from a miniaturization of the sensor and construction of an on-line system for a field installation, a considerable amount of time and energy can be saved by reducing mistake ratio and curtailing unnecessary processes. Originality/value: The measured ultrasonic waves allow for prediction of the casting speed necessary to correctly locate the liquid core and thereby maximize the benefits of soft reduction and the productivity of the machine.

Słowa kluczowe

EN

analysis; modeling; continuous casting process; electromagnetic transducers; solidification point; measured temperature

PL

analiza; modelowanie; proces ciągłego odlewania; przetwornik elektromagnetyczny; temperatura krzepnięcia; pomiar temperatury

• Wydawca: International OCSCO World Press
• Czasopismo: Journal of Achievements in Materials and Manufacturing Engineering
• Rocznik: 2006
• Tom: Vol. 17, nr 1-2
• Strony: 357--360
• Opis fizyczny: Bibliogr. 15 poz., rys., wykr.

Twórcy

autor

Kim I. S.

• Department of Mechanical Engineering, Mokpo National University, Jeonnam, 534-729, Korea

autor

Son J. S.

• Department of Mechanical Engineering, Mokpo National University, Jeonnam, 534-729, Korea

autor

Kim H. J.

• Korea Institute of Industrial Technology, Chungnam, 330-820, South Korea

autor

Chin B. A.

• Mechanical Engineering Department, Auburn University, AL, 36849-5341, USA

Bibliografia

• [1] D.A. Hutchins, R.J. Dewhurst, S.B. Palmer, Laser generated ultrasound at modified metal-surfaces, Ultrasonics 19 (3) (1981) 103-108.
• [2] M. Hirao, H. Ogi, An SH-wave EMAT technique for gas pipeline inspection, NDT E Int. 32 (3) (1999) 127-132.
• [3] H. Ogi, M. Hirao, T. Ohtani, Line-focusing electromagnetic acoustic transducers for the detection of slit defects, IEEE Trans. Ultrason. Ferroelectr. Freq. Contr. 46 (2) (1999) 341-346.
• [4] G.S. Kino, The application of reciprocity theory to scattering of acoustic waves by flaws, Journal of Applied Physics 49 (1978) 3190-3199.
• [5] M. Hirao, H. Fukuoka, Y. Miura, Scattering of Rayleigh surface waves by edge cracks-numerical-simulation and experiment, Journal of the Acoustical Society of America 72 (2) (1982) 602-606.
• [6] R.B. Thompson, New EMAT configuration for generating Sh-waves in ferromagnetic materials, IEEE Trans. Son. Ultrason. 26 (2) (1979) 149.
• [7] D. Achenbach, A.K. Gautesen, D.A. Mendelsohn, Ray analysis of surface-wave interaction with an edge crack, IEEE Transaction on SU 27 (1980) 124-129
• [8] Y.C. Angel, J.D. Achenbach, Reflection and transmission of obliquely incident Rayleigh waves by a surface-breaking crack, Journal of Acoustics Society of America 75 (1984) 313-319.
• [9] L.J. Bond, A computer model of the interaction of acoustic surface waves with discontinuities, Ultrasonics 17 (1979) 71-77.
• [10] Q. Shan, R. J. Dewhurst, Surface-breaking fatigue crack detection using laser ultrasound, Applied Physics Letters 62 (21) (1993) 2649-2651.
• [11] F. Ichikawa, Kawasaki Steel Corp, Instrumentation & Analytical Science Research Center, 1986 (unpublished).
• [12] BHP Research Laboratories, Newcastle and Melbourne Divisions, (1995).
• [13] A.K. Gautesen, Scattering of Rayleigh wave by an elastic quater space, Journal of Applied Mechanics 52 (1985) 664-668.
• [14] Y. Sohn, S. Krishnaswamy, Mass spring lattice modelling of the scanning laser source technique, Ultrasonics 39 (2002) 543-551.
• [15] I.A. Viktorov, Rayleigh waves in the ultrasonic range, Soviet Physical Acousctic 8 (1962) 119-129.