Synthesis of barium titanate piezoelectric ceramics for multilayer actuators (MLAs)

• Autorzy: Biglar M. , Stachowicz F. , Trzepieciński T. , Gromada M.

Identyfikatory

DOI

10.1515/ama-2017-0042

• Języki publikacji: EN

Abstrakty

EN

In this paper the characteristics of BaTiO3 ceramics synthesized by solid state method is presented. In order to receive the monophase ceramics the double activation and calcination were applied. A spray drier was used to granulate the powder of BaTiO3. Isostatic and uniaxial pressing were applied to manufacture the barium titanate pellets. The properties of fabricated BaTiO3 ceramics were determined at different stages of production. After the sintering phase, the hardness, the bending strength, the fracture toughness, and the coefficient of thermal expansion of barium titanate sinter were estimated. The BaTiO3 powder is characterized by spherical grains and the average size of 0.5 μm. The small value of the specific surface area of granulate ensured good properties of material mouldability and finally allowed to receive sinters of high density

Słowa kluczowe

EN

barium titanate; MLAs; multilayer actuator; solid state; piezoelectric ceramics

• Wydawca: Oficyna Wydawnicza Politechniki Białostockiej
• Czasopismo: Acta Mechanica et Automatica
• Rocznik: 2017
• Tom: Vol. 11, no. 4
• Strony: 275--279
• Opis fizyczny: Bibliogr. 21 poz., rys., tab., wykr.

Twórcy

autor

Biglar M.

• Faculty of Mechanical Engineering and Aeronautics, Department of Materials Forming, Rzeszow University of Technology, Powst. Warszawy 12, 35-959 Rzeszów, Poland

autor

Stachowicz F.

• Faculty of Mechanical Engineering and Aeronautics, Department of Materials Forming, Rzeszow University of Technology, Powst. Warszawy 12, 35-959 Rzeszów, Poland

autor

Trzepieciński T.

• Faculty of Mechanical Engineering and Aeronautics, Department of Materials Forming, Rzeszow University of Technology, Powst. Warszawy 12, 35-959 Rzeszów, Poland

autor

Gromada M.

• Institute of Power Engineering, Ceramic Department CEREL, Research Institute, ul. Techniczna 1, 36-040 Boguchwała, Poland

Bibliografia

• 1. Biglar M., Gromada M., Stachowicz F., Trzepieciński T. (2015), Optimal configuration of piezoelectric sensors and actuators for active vibration control of a plate using a genetic algorithm, Acta Mechanica, 226(10), 3451-3462.
• 2. Cai W., Fu C., Gao J., Guo Q., Deng X., Zhang C. (2011), Preparation and optical properties of barium titanate thin films, Physica B, 406, 3583-3587.
• 3. Choi M.-S., Kim S.-H., Kim Y.-H., Kim I.W., Jeong S.-J., Song J.- S., Lee J.-S. (2008), Application of Ag–ceramic composite electrodes to low firing piezoelectric multilayer ceramic actuators, Journal of Electroceramics, 20, 225-229.
• 4. Duran P., Gutierrez D., Tartaj J., Moure C. (2002), Densification behaviour, microstructure development and dielectric properties of pure BaTiO3 prepared by thermal decomposition of (Ba,Ti)-citrate polyester resins, Ceramics International, 28, 283-292.
• 5. Ertuğ B. (2013), The overview of the electrical properties of barium titanate American Journal of Engineering Research, 2(8), 1-7.
• 6. Hackenberger W.S., Pan M.-J., Vedula V., Pertsch P., Cao W., Randall C.A., Shrout T.R. (1998), Effect of grain size on actuator properties of piezoelectric ceramics, Smart Structures and Materials 1998: Smart Materials Technologies, 3324, 28-34.
• 7. Hwang H.J, Niihara K. (1998), Perovskite-type BaTiO3 ceramics containing particulate SiC: Part II Microstructure and mechanical properties, Journal of Materials Science, 33, 549-558.
• 8. Kao C.F., Yang W.D. (1999), Preparation of barium strontium titanate powder from citrate precursor, Applied Organometallic Chemistry, 13, 383-397.
• 9. Kholodkova A., Danchevskaya M., Fionov A. (2012), Study of nanocrystalline barium titanate formation in water vapour conditions, NANOCON Conference, 23-25.10.2012, Brno, Czech Republic.
• 10. Kim H.-T., Kim J.-H., Jung W.-S., Yoon D.-H. (2009), Effect of starting materials on the properties of solid-state reacted barium titanate powder, Journal of Ceramic Processing Research, (10)6, 753-757.
• 11. Luo J, Qiu J., Zhu K., Du J. (2011), Effects of the calcining temperature on the piezoelectric and dielectric properties of 0.55PNN0.45PZT ceramics, Ferroelectric, 425(1), 90-97.
• 12. Miot C., Proust C., Husson E. (1995), Dense ceramics of BaTiO3 produced from powders prepared by a chemical process, Journal of European Ceramic Society, 15, 1163-1170.
• 13. Moura F., Simoes A.Z., Aguiar E.C., Nogueira I.C., Zaghete M.A., Varela J.A., Longo E. (2009), Dielectric investigations of vanadium modified barium zirconium titanate ceramics obtained from mixed oxide method, Journal of Alloys and Compounds, 479, 280-283.
• 14. Nguyen D.Q., Lebey T., Castelan P., Bley V., Boulos M., Guillemet-Fritsch S., Combettes C., Durand B. (2007), Electrical and physical characterization of bulk ceramics and thick layers of barium titanate manufactured using nanopowders, Journal of Materials Engineering and Performance, 16(5), 626-634.
• 15. Othman K.I., Hassan A.A., Abdelal O.A.A., Elshazly E.S., Ali M.E.-S., El-Raghy S.M., El-Houte S. (2014), Formation mechanism of barium titanate by solid-state reactions, International Journal of Scientific& Engineering Research, (5)7, 1460-1465.
• 16. Prado L.R., de Resende N.S., Silva R.S., Egues S.M.S., SalazarBanda G.R. (2016), Influence of the synthesis method on the preparation of barium titanate nanoparticles, Chemical Engineering and Processing: Process Intensification, 103, 12-20.
• 17. Stojanovic B.D. (1999), Advanced in Sintered Electronic Materials, Advanced Science and Technology of Sintering, Kluwer Academic/Plenum Publishers, New York.
• 18. Vijatović M.M., Bobić J.D., Stojanović B.D. (2008), History and challenges of barium titanate: Part II, Science of Sintering, 40, 235-244.
• 19. Yoon D.-H., Lee B.I. (2004), Processing of barium titanate tapes with different binders for MLCC applications: Part I: Optimization using design of experiments, Journal of European Ceramic Society, 24, 739-752.
• 20. Yoshikawa S., Shrout T. (1993), Multilayer piezoelectric actuators – structures and reliability, AIAA/ASME/ASCE /AHS/ASC Structures, Structural Dynamics, and Materials Conference, 34th and AIAA/ASME Adaptive Structures Forum, La Jolla, CA, 19-22.04.1993, Technical Papers. Pt. 6, 3581-3586.
• 21. Zheng P., Zhang J.L., Tan Y.Q., Wang C.L. (2012), Grain-size effects on dielectric and piezoelectric properties of poled BaTiO3 ceramics, Acta Materialia, 60, 5022-5030.

Uwagi

1. The research leading to these results has received funding from the People Programme (Marie Curie Actions) of the European Union's Seventh Framework Programme FP7/2007-2013/ under REA grant agreement No. PITN-GA-2013- 606878.

2. Opracowanie rekordu w ramach umowy 509/P-DUN/2018 ze środków MNiSW przeznaczonych na działalność upowszechniającą naukę (2018).