Contact Stress Simulation for Mg-0.5Ca-xMn Alloys used for Medical Application

• Autorzy: Nastasa Roxana Oana , Tufescu Ana , Munteanu Corneliu , Istrate Bogdan , Przybył Anna , Ianus Gelu

Identyfikatory

DOI

10.24425/amm.2022.137771

• Języki publikacji: EN

Abstrakty

EN

In the past decades, Mg alloys have been studied intensively as potential orthopedic applications. The present research work, the FEA of the obtained contact stresses in the case of the load applied on Mg-0.5Ca-xMn alloys has been investigated. It has been used the NCB Curved Femur Shaft Plate type as a model in order to establish the necessary modeling parameters. The objective of the present work was to highlight the strain values at the contact point on the surface of the Mg-0.5Ca-xMn alloys. The results showed that the highest stresses observed near the gaps of the plate and in the screws. It means that all mechanical loads are sustained by the plate and screws, and the patient’s femur can be recovered.

Słowa kluczowe

EN

Mg-Ca-Mn alloys; FEA analysis; mechanical properties

• Wydawca: Institute of Metallurgy and Materials Science of Polish Academy of Sciences ; Committee of Materials Engineering and Metallurgy of Polish Academy of Sciences
• Czasopismo: Archives of Metallurgy and Materials
• Rocznik: 2022
• Tom: Vol. 67, iss. 2
• Strony: 405--408
• Opis fizyczny: Bibliogr. 24 poz., rys., tab.

Twórcy

autor

Nastasa Roxana Oana

• Gheorghe Asachi Technical University, Faculty of Mechanical Engineering, Blvd. Mangeron, No. 43, 700050, Iasi, Romania

• https://orcid.org/0000-0001-5728-1315

autor

Tufescu Ana

• Gheorghe Asachi Technical University, Faculty of Mechanical Engineering, Blvd. Mangeron, No. 43, 700050, Iasi, Romania

• https://orcid.org/0000-0002-0851-6023

autor

Munteanu Corneliu

• Gheorghe Asachi Technical University, Faculty of Mechanical Engineering, Blvd. Mangeron, No. 43, 700050, Iasi, Romania
• Technical Science Academy of Romania, 26 Dacia Blvd, Bucharest 030167, Romania

• https://orcid.org/0000-0002-3878-9129

autor

Istrate Bogdan

• Gheorghe Asachi Technical University, Faculty of Mechanical Engineering, Blvd. Mangeron, No. 43, 700050, Iasi, Romania

• https://orcid.org/0000-0003-0817-3523

autor

Przybył Anna

• Częstochowa University of Technology, Department of Physics, 19 Armii Krajowej Av., 42-200 Częstochowa, Poland

• https://orcid.org/0000-0003-0428-3004

autor

Ianus Gelu

• Gheorghe Asachi Technical University, Faculty of Mechanical Engineering, Blvd. Mangeron, No. 43, 700050, Iasi, Romania

• https://orcid.org/0000-0002-2998-0992

Bibliografia

• [1] I. Antoniac, R. Adam, A. Bita, M Miculescu, O. Trante, I.M. Petrescu, M. Pogarasteanu, Materials 14 (1), 84 (2021).
• [2] I.V. Antoniac, D.I. Stoia, B. Ghiban, C. Tecu, F. Miculescu, C. Vigaru, V. Saceleanu, Materials 12 (7), 1128 (2019).
• [3] L. Huafang, Z. Yufeng, Q. Ling, Progress in Natural Science: Materials International 24 (5), 414-422 (2014).
• [4] M.S. Baltatu, P. Vizureanu, T. Balan, M. Lohan, C.A. Tugui, IOP Conference Series-Materials Science and Engineering 374, 012023 (2018).
• [5] M.S. Baltatu, C.A. Tugui, M.C. Perju, M. Benchea, M.C. Spataru, A.V. Sandu, P. Vizureanu, Revista de Chimie 70 (4), 1302-1306 (2019).
• [6] M.G. Minciuna, P. Vizureanu, M. Mares, V. Nastasa, D.C. Achitei, A.V. Sandu, Revista de Chimie 67 (2), 362-365 (2016).
• [7] Y.F. Zheng, X.N. Gu, F. Witte, Materials Science and Engineering: R: Reports 77, 1-34 (2014).
• [8] B. Istrate, J.V. Rau, C. Munteanu, I.V. Antoniac, V. Saceleanu, Ceramics International 46 (10), 15897-15906 Part: B (2020).
• [9] I. Antoniac, F. Miculescu, C. Cotrut, A. Ficai, J.V. Rau, E. Grosu, A. Antoniac, C. Tecu, G Cristescu, Materials 13 (2), 263 (2020).
• [10] N. Cimpoesu, L.C. Trinca, G. Dascalu, S. Stanciu, S.O. Gurlui, D. Mareci, Journal of Chemistry, article number: 9520972 (2016).
• [11] C. Tecu, I. Antoniac, G. Goller, B. Yavas, D. Gheorghe, A. Antoniac, I Ciuca, A. Semenescu, A.D. Raiciu, I. Cristescu, Materiale Plastice 56 (3), 644-648 (2019)
• [12] C. Zhang, L. Wu, G. Huang, Y. Huang, B. Jiang, A. Atrens, F. Pan Journal of Alloys and Compounds 823, 153844 (2020).
• [13] R. Vijayakumar, M. Madheswaran, Conference on Emerging Devices and Smart Systems (ICEDSS), 224-228.
• [14] D. Chandramohan, L. Ravikumar, Materials Today: Proceedings 16 (2), 744-749 (2019).
• [15] K.N. Chethan, S.N. Bhat, M. Zuber, S.B. Shenoy, Open Biomed. Eng. J. 12 (1), 108-114.
• [16] M. Nica, B. Cretu, D. Ene, I. Antoniac, D. Gheorghita, R. Ene, Materials 13 (5), 1201 (2020).
• [17] A. Almasi, I. Antoniac, S. Focsaneanu, M. Manole, R. Ciocoiu, O. Trante, K. Earar, A. Saceleanu, A. Porumb, C. Ratiu, Revista de Chimie 70 (1), 336-342 (2019)
• [18] Catalog NCB® Periprosthetic Femur System Surgical Technique.
• [19] ISO 5835-1:1985 - Implants for surgery Metal bone screws with hexagonal drive connection, spherical under-surface of head, asymmetrical thread Dimensions.
• [20] S. Lupescu, C. Munteanu, A. Tufescu, B. Istrate, N. Basescu, IOP Conference Series: Materials Science and Engineering 997, 012024 (2020).
• [21] http://www.hbnewmaterial.com/supplier129192-master-alloy
• [22] S. Lupescu, B. Istrate, C. Munteanu, M.G. Minciuna, S. Focsaneanu, K. Earar, Revista de Chimie 68, 1408-1413 (2017).
• [23] https://mri.radiology.uiowa.edu/
• [24] V. Guerrero, A. Luis, D. Ramírez, I. Edgar, C. Ruiz, Osvaldo, P.A. Ortiz, Memorias del xxi Congreso Internacional Anual de la Somim Coatzacoalcos Veracruz México, 0495-0503 (2015).

Uwagi

1, This work was supported by a grant of the Romanian Ministery of Research and Innovation, CCCDI-UEFISCDI, project number PN-III-P1-1.2-PCCDI-2017-0239 / 60PCCDI 2018, within PNCDI III.

2. Opracowanie rekordu ze środków MEiN, umowa nr SONP/SP/546092/2022 w ramach programu "Społeczna odpowiedzialność nauki" - moduł: Popularyzacja nauki i promocja sportu (2022-2023).