Impact of Cutting Forces and Chip Microstructure in High Speed Machining of Carbon Fiber - Epoxy Composite Tube

• Autorzy: Allwin Roy Y. , Gobivel K. , Vijay Sekar K. S. , Suresh Kumar S.

Identyfikatory

DOI

10.1515/amm-2017-0269

• Języki publikacji: EN

Abstrakty

EN

Carbon fiber reinforced polymeric (CFRP) composite materials are widely used in aerospace, automobile and biomedical industries due to their high strength to weight ratio, corrosion resistance and durability. High speed machining (HSM) of CFRP material is needed to study the impact of cutting parameters on cutting forces and chip microstructure which offer vital inputs to the machinability and deformation characteristics of the material. In this work, the orthogonal machining of CFRP was conducted by varying the cutting parameters such as cutting speed and feed rate at high cutting speed/feed rate ranges up to 346 m/min/ 0.446 mm/rev. The impact of the cutting parameters on cutting forces (principal cutting, feed and thrust forces) and chip microstructure were analyzed. A significant impact on thrust forces and chip segmentation pattern was seen at higher feed rates and low cutting speeds.

Słowa kluczowe

EN

composite materials; orthogonal machining; cutting forces; chip microstructure

• Wydawca: Institute of Metallurgy and Materials Science of Polish Academy of Sciences ; Committee of Materials Engineering and Metallurgy of Polish Academy of Sciences
• Czasopismo: Archives of Metallurgy and Materials
• Rocznik: 2017
• Tom: Vol. 62, iss. 3
• Strony: 1771--1777
• Opis fizyczny: Bibliogr. 15 poz., rys., tab.

Twórcy

autor

Allwin Roy Y.

• Mount Zion College of Engineering and Technology, Pudukottai, Tamilnadu, India

autor

Gobivel K.

• KCG College of Technology, Chennai, Tamilnadu, India

autor

Vijay Sekar K. S.

• SSN College of Engineering, Chennai, India

autor

Suresh Kumar S.

• SSN College of Engineering, Chennai, India

Bibliografia

• [1] R. Ch. Dandekar, C. Y. Shin, Int. J. Mach. Tool 57, 102-121 (2012).
• [2] Ch.-S. Chang, J. Mater. Process. Tech. 180, 117-129 ( 2006).
• [3] C. Dold, M. Henerichs, L. Bochmann, K. Wegener, Procedia CIRP, 178-183 (2012).
• [4] K. S. Kim, D. G. Lee, K. Kwak, S. Namgung, J. Mater. Process. Tech. 32, 553-570 (1992).
• [5] O. Pecat, R. Rentsch, E. Brinksmeier, Procedia CIRP, 466-470 (2012).
• [6] R. Rusinek, Int. J. Non Linear Mech. 45, 458-462 (2010).
• [7] M. Rahman, S Ramakrishna, J. R. S. Prakash, D. C. G. Tan, J. Mater. Process. Tech. 89-90, 292-297 (1999).
• [8] Rajasekaran, Palanikumar, Vinayagam Procedia Eng. 38, 2922-2929 (2012).
• [9] R. Rentsch, O. Pecat, E. Brinksmeier, Procedia Eng. 10, 1823-1828 (2011).
• [10] G. Santhanakrishnan, R. Krishnamurthy, S.K. Malhotra, Investigation into the machining of carbon-fiber reinforced plastics with cemented carbides, J. Mater. Process. Tech. 300, 263-275 (1992).
• [11] T. Yashiro, T. Ogawa, H. Sasahara, Int. J. Mach. Tool Manu. 70, 63-69 (2013).
• [12] R. Teti, CIRP Annals-Manu. Tech. 51, 611-634 (2012).
• [13] V. Krishnaraj, Prabukarthi, A. Ramanathan, Elanghovan, S. Kumar, R. Zitoune, Davim, Composites: Part B , pp.1791-1799 (2012).
• [14] X. M. Wang, L. C. Zhang, Int. J. Mach. Tool Manu. 43, 1015-1022 (2003).
• [15] Y. Karpat. N. Polat, CIRP Ann-Manu. Tech. 62, 95-98 (2013).

Uwagi

EN

1. The authors wish to express their gratitude to AICTE, Govt. of India for sponsoring this research project under a Research Promotion Scheme (RPS) grant.

PL

2. Opracowanie rekordu w ramach umowy 509/P-DUN/2018 ze środków MNiSW przeznaczonych na działalność upowszechniającą naukę (2018).