Shot Peening of a Mg-Al-Zn-Mn Alloy Surface

• Autorzy: Kottfer D. , Mrva P.
• Języki publikacji: EN

Abstrakty

EN

The paper describes the influence of shot peening on Mg-Al-Zn-Mn alloy surface. There are estimates focusing on the roughness of the shot peened surfaces and size of the selected shot peened material - corund. Based on the results of measurements, the evaluation was oriented on the curve of roughness, functionality of surface roughness Ra and the necessary quantity of shot peening material qnR of estimated material depending on the grain size dz.

Słowa kluczowe

EN

materials technology; shot peening; functional surface; roughness

• Wydawca: Wojskowa Akademia Techniczna im. Jarosława Dąbrowskiego
• Czasopismo: Problemy Mechatroniki : uzbrojenie, lotnictwo, inżynieria bezpieczeństwa
• Rocznik: 2010
• Tom: Vol. 1, Nr 1 (1)
• Strony: 21--29
• Opis fizyczny: Bibliogr. 17 poz., il., wykr.

Twórcy

autor

Kottfer D.

autor

Mrva P.

• Department of Technologies and Materials, Faculty of Mechanical Engineering Technical University of Košice, Mäsiarska 74, 040 01 Košice, Slovakia,

Bibliografia

• [1] Piľa J., Sloboda A., Sloboda A., Some opportunities of diagnostic parameters utilization in the aircraft proactive maintenance management, Proceedings of 7th International Scientific Conference DIS 2004: Theroy and application of techniques of technical diagnostics, Košice, 13-14 October 2004, Slovakia, pp. 76-82, 2004.
• [2] Neštrák D., Piľa J., Helicopter aerodynamics, structures and systems (in Slovak), Akademické nakladatelství CERM, Brno, Czech Republic, 2006.
• [3] Kuffová M., BellaV., Fatigue resistance of magnesium alloy AZ 91D. Kovové materiály - Metallic Materials, vol. 47, no. 6, pp. 415-420, 2009.
• [4] Kuffová M., Microstructure of magnesium alloys after heat treatment. Proceedings of Conference Wear, Dependability, Diagnostics 2006, Brno, Czech Republic, p. 139, 2006.
• [5] Mrva P., Kottfer D., Influence of thermal spray coatings on the thermal endurance of magnesium alloy ML-5, Acta Polytechnica Hungarica, vol. 6, no. 2, Hungary, pp. 71-75, 2009.
• [6] Mrva P., Kaliský S., Mathematical model evaluation of the shot peening technological process of Ti alloys onto adhesion of plasma sprayed coatings with thermal insulating properties (in Slovak), Proceedings of 4th International Conference: Corosion and Corrosion Protection of Matrials (in Slovak), 12-13 April 2000, Trenčín, Slovakia, pp. 124-128, 2000.
• [7] Kniewald D., Pivoda P., Mechanical pretreatment of the surface of parabolic springs under protective Al and Zn thermal sprayed coatings (in Slovak), Zborník vedeckých prác VŠT v Košiciach 1978, Slovakia, pp. 309-318, 1978.
• [8] Mrva P., Research of the influence of the surface pretreatment of titanium alloys (in Czech), Research report VU 070 Brno, Czech Republic, 1986.
• [9] Kniewald D., Šefara M., Vorbehandlung der Metalloberfläche durch Strahlen als Vorbereirung fűr Schutzűberzűge aus Pulverkunststoffen, Zborník vedeckých prác VŠT v Košiciach, 1980, Slovakia, pp. 263-274, 1980.
• [10] Štěpánek M., Neštrák D., Handbook of the aviation technician (in Slovak), Translation, Naše vojsko, Praha, Slovakia, 1989.
• [11] Matting A., Steafens H. D., METALLURGY, no. 10, Germany, pp. 13-17, 1968.
• [12] Sedláček V., Metall surfaces and coatings (in Czech), ČVUT Praha,Czech Republic, 1992.
• [13] Slámečka K., Pokluda J., Kianicová M., Major Š., Dvořák I., Quantitative fractography of fish-eye crack formation under bending-torsion fatigue, International Journal of Fatigue, vol. 32, Issue 6, (2010), pp. 921-928, 2010.
• [14] Zhu D., Miller R.A, Development of advanced low conductivity thermal barrier coatings, International Journal of Applied Ceramic Technologies, vol. 1 [1], (2004), pp. 86-94, 2004.
• [15] Hatamleh O., Smith J., Cohen D, Bradley R., Surface roughness and friction coefficient in peened friction stir welded 2195 aluminium alloy, Applied Surface Science, vol. 255, Issue 16, (2009), pp. 7414-7426, 2009.
• [16] Kottfer D., Mrva P., Mechanical pre-treatment of surface of aluminium alloy D16-T by shot peening, Acta Polytechnica Hungarica, vol. 6, no. 4, (2009), pp. 75-82, 2009.
• [17] Mrva P., Kottfer D., Effect of shot peening and NiAl coating on fatigue limit of Mg-Al-Zn-Mn alloy, Surface Review and Letter, vol. 17, (2010) (in print), 2010.