Adhesive bonded hot dip zinc coated sheet and titanium sheet joint strength - numerical analysis

• Autorzy: Rudawska A. , Dębski H.
• Języki publikacji: EN

Abstrakty

EN

This paper describes a numerical analysis of adhesively bonded hot dip zinc coated sheet and titanium sheet and its comparison with the results of experimental tests. The study aims at presenting a comparative analysis of numerical calculation results with the results of strength test of the joints in question. Numerical simulations are an invaluable extension of experimental tests and, moreover, prove particularly useful at joint designing and analysis stages. The calculations were conducted with ABAQUS Standard software and allowed for the destructive force value obtained in experimental tests. Strength tests were conducted on single-lap adhesive joints for given structural materials; the samples were shear-loaded. The comparison of the results of experimental tests and numerical analysis led us to observe certain inconsistencies in the destructive force values, consequently providing information on the accuracy of a numerical model when compared with the actual model. Geometric model of the analysed single-lap adhesive joint, numerical model of the analysed single-lap adhesive joint, adhesive layer failure criterion description, visualisation of the analysed single-lap joint failure process, visualisation of adhesive joint failure stages of adhesive layer are presented.

Słowa kluczowe

EN

adhesive joint; finite elements method (FEM); adhesive joints strength

• Wydawca: Łukasiewicz Research Network - Institute of Aviation ; European Science Society of Powertrain and Transport KONES Poland ; Wydawnictwo Instytutu Technicznego Wojsk Lotniczych
• Czasopismo: Journal of KONES
• Rocznik: 2012
• Tom: Vol. 19, No. 1
• Strony: 339--345
• Opis fizyczny: Bibliogr. 16 poz., rys.

Twórcy

autor

Rudawska A.

autor

Dębski H.

• Technical University of Lublin, Department of Production Engineering Nadbystrzycka Street 36, 20-618 Lublin, Poland tel.:[phone],

Bibliografia

• [1] Abaqus 6.9, Documentation, 2009.
• [2] Abaqus/Standard User’s Manual version 6.5, Hibbit, Karlsson & Sorensen, Inc., 2005.
• [3] Czaplicki, J., Ćwikliński, J., Godzimirski, J., Konar, P., Klejenie tworzyw konstrukcyjnych, WKŁ, Warszawa 1987.
• [4] Godzimirski, J., Wytrzymałość doraźna konstrukcyjnych połączeń klejowych, Wyd. WNT, Warszawa 2002.
• [5] Godzimirski, J., Kozakiewicz, J., Łunarski, J., Zielecki, W., Konstrukcyjne połączenia klejowe elementów metalowych w budowie maszyn, Oficyna Wydawnicza Politechniki Rzeszowskiej, Rzeszów 1997.
• [6] Goglio, L., Rossetto, M., Dragoni, E., Design of adhesive joint based on peak elastic stresses, International Journal of Adhesion and Adhesives, 28, pp. 427-435, 2008.
• [7] Grant, L. D. R., Adams, R. D., da Silva, L. F. M., Effect of the temperature on the strength of adhesively bonded single lap and T joints for the automotive industry, International Journal of Adhesion and Adhesives, 29, pp. 535-542, 2009.
• [8] Moura,M. F. S. F., Concalves, J. P. M., Chousal, J. A. G., Campilho, R. D. S. G., Cohesive and continuum mixed-mode damage models applied to the simulation of the mechanical behavior of bonded joints, International Journal of Adhesion and Adhesives, 28, pp. 419-426, 2008.
• [9] Rudawska, A., Dębski, H., Ocena wytrzymałości połączeń klejowych blach ze stopu aluminium z wykorzystaniem analizy numerycznej MES, Eksploatacja i Niezawodność, No. 1, pp. 4-10, 2011.
• [10] Rudawska, A., Dębski, H., Modelowanie procesu zniszczenia spoiny klejowej w jednozakładkowym połączeniu klejowym blach aluminiowych, Mechanik, Nr 2, pp. 118 121, 2010.
• [11] Rudawska, A., Adhesive joint strength of hybrid assemblies: Titanium sheet composites and aluminium sheet-composites—Experimental and numerical verification, International Journal of Adhesion and Adhesives, 29, pp. 451-457, 2010.
• [12] Rusiński, E., Czmochowski, J., Smolnicki, T., Zaawansowana metoda elementów skończonych w konstrukcjach nośnych, Oficyna Wydawnicza Politechniki Wrocławskiej, Wrocław 2000.
• [13] da Silva, L. F. M., Adams, R. D., Techniques to reduce the peel stresses in adhesive joints with composites, International Journal of Adhesion and Adhesives, 27, pp. 227-235, 2007.
• [14] Taib, A. A., Boukhili, R., Achiou, S., Gordon, S., Boukehili, H., Bonded joints with composite adherends. Part I. Effect of specimen configuration, adhesive thickness, spew fillet and adherend stiffness on fracture. International Journal of Adhesion and Adhesives, 26, pp. 226-236, 2006.
• [15] Wang, J., Zhang, Ch., Three-parameter, elastic foundation model for analysis of adhesively bonded joints, International Journal of Adhesion and Adhesives, 29, pp. 495-502, 2009.
• [16] You, M., Yan, Z.-M., Zheng, X.-.L, Yu, H.-.Z, Li, Z., A numerical and experimental study of gap length on adhesively bonded aluminium double-lap joint, International Journal of Adhesion and Adhesives, 27, pp. 696-702, 2007.