The analysis of finishing tooling influence on corrosion properties researched by EIS

• Autorzy: Labuda W. , Charchalis A.
• Języki publikacji: EN

Abstrakty

EN

Angular momentum pumps are very often applied onboard ships. These pumps are used in cooling circuits of medium and high power engines, power plant boilers and in bilge, ballast and fire installations. Very extensive use of angular momentum pumps on board is connected with their numerous advantages. During operation the wear of marine hull, the rotor and shaft seals take place. The research attempts to increase the service life of shafts. The article presents the research results referring to the analysis of the influence of finish treatment (lathing, grinding and burnishing) on the corrosion properties of steel applied to marine pump shafts. The research was performed on a roller of 40 mm in diameter made of X5CrNi18-10 (AISI 304 L) stainless steel. The lathing process was carried out by means of a WNMG WF 080408 Sandvik Coromant cutting tool with replaceable inserts. The grinding process was performed by grinding attachment for lathes. The 1 - 80x10x32 - 99C 80-N V grinding wheel was used for the process. The process of burnishing was done by SRMD burnisher by Yamato. In addition, the influence of the burnisher passes number on the corrosion properties was determined. The paper will present the results of electrochemical impedance spectroscopy research. To conduct the survey the Atlas 0531 EU and IA potentiostat was used. Determination of the corrosion process parameters was performed computer programs: AtlasLab 2.0 and EIS Spectrum Analyzer.

Słowa kluczowe

EN

burnishing; surface layers; angular momentum pump; corrosion properties; EIS

• Wydawca: Łukasiewicz Research Network - Institute of Aviation ; European Science Society of Powertrain and Transport KONES Poland ; Wydawnictwo Instytutu Technicznego Wojsk Lotniczych
• Czasopismo: Journal of KONES
• Rocznik: 2012
• Tom: Vol. 19, No. 1
• Strony: 237--244
• Opis fizyczny: Bibliogr. 14 poz., rys.

Twórcy

autor

Labuda W.

autor

Charchalis A.

• Gdynia Maritime University The Faculty of Marine Engineering Morska Street 83, 81-225 Gdynia tel.: [phone], fax: [phone],

Bibliografia

• [1] Bala, H., Korozja materiałów – teoria i praktyka, Wydawnictwo Wydziału Inżynierii Materiałowej i Fizyki Stosowanej Politechniki Częstochowskiej, Częstochowa 2002.
• [2] Budniok, A., Łągiewka, E., Problemy elektrochemii w inżynierii materiałowej, Wydawnictwo Uniwersytetu Śląkiego, Katowice 2009.
• [3] Charchalis, A., Starosta, R., Labuda, W., Estimation of the influence of burnishing tool passes number on ships pumps shafts surface layers strengthening and roughness changes, Journal of KONES Powertrain and Transport, Vol. 16, No. 4, pp. 43–50, Zakopane 2009.
• [4] Charchalis, A., Starosta, R., Labuda, W., Multi-criteria optimization of steel burnishing parameters applied to marine pumps shaft pins, Journal of KONES Powertrain and Transport, Vol. 17, No. 3, pp. 55–62, Jurata 2010.
• [5] Charchalis, A., Starosta, R., Labuda, W., The influence of burnishing parameters on the roughness, plastic strain and shape deviations of marine pumps crankshaft pins in fresh water installations; Journal of KONBiN, No 1-2 (9,10), pp. 57-66, Warszawa 2009.
• [6] Dyl, T., Skoblik, R., Starosta, R., The Effect of the Ceramic Dispersion on the Nickel Matrix Composite Coating Properties after Plastic Working, Solid State Phenomena, Vol. 147-149, pp. 813-818, Switzerland 2009.
• [7] Dyl, T., Starosta, R., Skoblik, R., The effect of the unit pressure on the NiAl and Ni3Al intermetallic coatings selection parameters after plastic working. Solid State Phenomena, Vol. 165, p. 19-24, Switzerland 2010.
• [8] Labuda, W., Starosta, R., Estimation of the influence of burnishing parameters on X5CrNi18- 10 steel, Solid State Phenomena, Trans Tech Publication, Vol. 165, pp 300–305, Switzerland 2010.
• [9] Labuda, W., Starosta, R., Dyl, T., Estimation of the influence of burnishing parameters on steel X5CrNi1810 surface layers strengthening and roughness changes, Journal of KONES Powertrain and Transport, Vol. 15, No. 3, pp. 259–267, Warszawa 2008.
• [10] Starosta, R., The influence of plastic strain on the corrosive properties of plasma sprayed intermetallic NiAl and Ni3Al coatings, Solid State Phenomena, Vol. 165, pp. 165-177, Switzerland 2010.
• [11] Przybylski, W., Wpływ stanu warstwy wierzchniej konstytuowanej przez nagniatanie na trwałość elementów maszyn, Wybrane problemy Trybologii, PWN, Warszawa 1990.
• [12] Przybylski, W., Współczesne problemy w technologii obróbki przez nagniatanie, Wydawnictwa Politechniki Gdańskiej, Gdańsk 2005.
• [13] Przybylski, W., Współczesne problemy w technologii obróbki przez nagniatanie, Tom 2, Wydawnictwa Politechniki Gdańskiej, Gdańsk 2008.
• [14] Trzaska, M., Trzaska, Z., Elektrochemiczna spektroskopia impedancyjna w inżynierii materiałowej, Wydawnictwa Politechniki Warszawskiej, Warszawa 2010.