Novel developments in dimensional nanometrology in the context of Geometrical Product Specifications and Verification (GPS)

• Autorzy: Durakbasa M. N. , Osanna P. H. , Bas G. , Demircioglu P. , Cakmakci M. , Hornikova A.
• Języki publikacji: EN

Abstrakty

EN

Adequate knowledge in the areas of intelligent coordinate metrology and design are important presuppositions to achieve waste free production and low costs of manufacturing with higher quality and accuracy at the same time. This is of extreme importance in present time of worldwide international competition in industry and production and at the same time increasingly higher costs of energy and raw material. The prescription and consumption of material and energy to achieve the necessary and required workpiece accuracy in series manufacturing depends to a great extent from the (geometrical) workpiece tolerances of any kind (roughness, form, positional, dimensional) which are prescribed for the production and the fulfillment of these tolerances and therefore for the function of the produced workpieces and their fitness for practical application and none the less of the economy of production altogether. This requirement is of great importance at the time being which is characterized as described above.

Słowa kluczowe

EN

precision metrology; design; manufacturing; workpiece tolerancing

• Wydawca: Łukasiewicz Industrial Research Institute for Automation and Measurements PIAP
• Czasopismo: Journal of Automation Mobile Robotics and Intelligent Systems
• Rocznik: 2012
• Tom: Vol. 6, No. 2
• Strony: 22--25
• Opis fizyczny: Bibliogr. 17 poz., rys.

Twórcy

autor

Durakbasa M. N.

autor

Osanna P. H.

autor

Bas G.

autor

Demircioglu P.

autor

Cakmakci M.

autor

Hornikova A.

• Vienna University of Technology (TU-Wien), Head of Department of Interchangeable Manufacturing and Industrial Metrology (Austauschbau und Messtechnik/Produktionsmesstechnik & Qualität), Institute of Production Engineering and Laser Technology, Vienn,

Bibliografia

• [1] Digital Microscope Keyence VHX-600, http://www.digitalmicroscope.com/solutions/digital-microscope.php.
• [2] Osanna P. H., Durakbasa M.N., Kräuter L., “Industrial Metrology and Interchangeable Manufacturing under the Viewpoint of Nanotechnology and Nanometrology”, Bulgarian Academy of Sciences, Problems of Engineering Cybernetics and Robotics, vol. 59, 2008, pp.60-73.
• [3] Tabenkin A., “Effects of Form and Finish on Tolerances”, Quality, vol. 9, 1993.
• [4] D. Whitehouse, “Comparison between stylus and optical methods for measuring surfaces”, Annals CIRP, vol. 37, no. 2 , 1988, pp. 649-653.
• [5] EN ISO 4287:2009, Geometrical Product Specifications (GPS) – Surface texture: Profile method – Terms, definitions and surface texture parameters (ISO 4287:1997 + Cor 1:1998 + Cor 2:2005 + Amd 1:2009).
• [6] EN ISO 1101:2006: Geometrical Product Specifications (GPS) – Geometrical Tolerancing – Tolerances of Form, Orientation, Location and Run-out; EN ISO 1101/A1:2010 Geometrical Product Specifications (GPS) – Geometrical tolerancing –Tolerances of form, orientation, location and run-out-Amendment 1: Representation of specifications in the form of a 3D model.
• [7] EN ISO 8015:2011 – Geometrical product specifications (GPS) – Fundamentals – Concepts, principles and rules.
• [8] EN ISO 9001: 2008: Quality Management Systems – Requirements. 2008-12.
• [9] EN ISO 14001:2009: Environmental management systems – Requirements with guidance for use (ISO 14001:2004 + Cor. 1:2009).
• [10] EN ISO 9004:2009: Managing for the sustained success of an organization – A quality management approach.
• [11] Taniguchi N., “On the Basic Concept of Nanotechnology”. In: Proc. Int. Conf. Prod. Eng., Tokyo, JSPE, 1974, part 2, pp. 18-23.
• [12] Binnig G., H. Rohrer, “The Scanning Tunnelling Microscope”, Sci. Amer., no. 253, 1985, pp. 40-46.
• [13] Binnig G., H. Rohrer, “Scanning Tunnelling Microscopy”, IBM J. Res. Develop., vol. 30, 1986, pp. 355-369.
• [14] ISO TR 14638: Geometrical product specification (GPS) – Masterplan, 1995.
• [15] Ballu A., Mathieu L., “Univocal Expression of Functional and Geometrical Tolerances for Design, Manufacturing and Inspection”. In: 4th CIRP Seminar on Computer Aided Tolerancing, Tokyo, Japan, 1995, pp. 31-46.
• [16] N.M. Durakbasa, A. Sadat, A. Nomak, “Dimensional and Geometrical Measurement and Interpretation of Measuring Results on the Basis of the Skin Model”, Measurement Science Review, vol. 1, no. 1, 2001, pp. 89-92.
• [17] P.H. Osanna, N.M. Durakbasa et al.: “Global Competitive Manufacturing on the Basis of Intelligent Metrology and Quality Management as Important Tools”. In: Proceedings of the International Symposium Tools and Methods of Competitive Engineering – TMCE 2002, Ed.: I. Horvath et al.,Wuhan, China, April 2002, ISBN 7-5609-2682-7, pp. 837-844.