Analysis of a protective composite panel with energy adsorbent in the form of foamed aluminium

• Autorzy: Barnat W. , Panowicz R. , Niezgoda T. , Gieleta R.
• Języki publikacji: EN

Abstrakty

EN

The article presents the results of the investigations into modelling a blast wave for huge charges of l kg TNT equivalent. Modelling of huge charges is a very interesting problem due to a scale effect. During numerical analyses a detonation phenomenon was ignored (for the reason of the analysis time). The paper considers the effects of the influence of a pressure wave coming from a huge TNT charge (modelled with energy) on a 6 mm thick steel plate as well as on a protective panel made of foamed aluminium with composite layer. A panel of foamed aluminium was used for the protection of the described plate. The particular elements of a panel, subjected to an experimental analysis, were jointed with the use of a glueing method. In the numerical model the particular component layers were jointed with contact. The ALE (Arbitrary-Lagrange-Euler) function was used for coupling between the Euler domain and the Lagrange domain. The method requires absolute location compatibility of the nodes from both jointed areas. In the results of the conducted investigations, the permanent deformation of the steel plate was obtained.. Additionally, the possibility of the steel plate deformation evaluation was considered on the basis of accessible literature. Due to a huge charge, the analysis was performed with the use of the finite element method with the eiperimental verification.

Słowa kluczowe

EN

blast wave; analytical model; FE analysis; aluminium panel

• Wydawca: Łukasiewicz Research Network - Institute of Aviation ; European Science Society of Powertrain and Transport KONES Poland ; Wydawnictwo Instytutu Technicznego Wojsk Lotniczych
• Czasopismo: Journal of KONES
• Rocznik: 2010
• Tom: Vol. 17, No. 4
• Strony: 35--44
• Opis fizyczny: Bibliogr. 12 poz., rys.

Twórcy

autor

Barnat W.

autor

Panowicz R.

autor

Niezgoda T.

autor

Gieleta R.

• Department of Mechanics and Applied Computer Science Military University of Technology, Faculty of Mechanical Engineering Kaliskiego Street 2, 00-908 Warsaw, Poland tel: [phone], fax: [phone],

Bibliografia

• [1] MSC.Dytran, Theory Manual, Wydawnictwo MSC, 2002.
• [2] Sedov, L. I., Propagation of intense blast waves, PMM, 10, 241, 1946.
• [3] Taylor, J. L., The formation of a blast wave by a very intense explosion, cz. I, Proc.Roy. Soc. A, 201, 159.
• [4] Von Neumann, J., The point source solution, National Defence Research Committee, Div. B Report AM-9.
• [5] Staniukowicz, K. P., Fizyka wzrywa, Moskwa 1975.
• [6] Jach, K., et. al., Komputerowe modelowanie dynamicznych oddziaływań metodą punktówswobodnych, PWN, Warszawa 2001.
• [7] Włodarczyk, E., Wstęp do mechaniki wybuchu, PWN, Warszawa 1994.
• [8] Krzewiński, R., Rekrucki, R., Roboty budowlane przy użyciu materiałów wybuchowych,Polcen,2005.
• [9] Dobrociński, S., Stabilność rozwiązań zagadnień odporności udarowej konstrukcji, AMWGdynia 2000.
• [10] Adamik, V., Trzciński, W., Trąbiński, R., Cudziło, S., Investigation of the Behaviour of Steeland Laminated Fabric Plates Under Blast Wave Load, V International Armament Conference, Waplewo 2005.
• [11] MSC.Dytran Example problems Wydawnictwo MSC, 2002.
• [12] Barnat, W., Numeryczno doświadczalna analiza złożonych warstw ochronnych obciążonych falą uderzeniowa wybuchu, Bell Studio 2009.