Narzędzia help

Preferencje help
Widoczny [Schowaj] Abstrakt
Liczba wyników
first previous next last
cannonical link button


Journal of KONES

Tytuł artykułu

Self-regeneration method of diesel particulate filter

Autorzy Mitianiec, W. 
Treść / Zawartość
Warianty tytułu
Języki publikacji EN
EN Compression ignition engines have no possibility for self-regeneration of DPF and regeneration requires additional energy for soot combustion (additional fuel or electric energy) after some period of the engine work as a result of closing of substrate pores by soot. The innovation method takes into account a self-regeneration of diesel particle filter by use of special heat recovery system. The paper shows one of possible design of DPF self-regeneration. The exhaust temperature behind the turbine and catalytic converter is very low and for an increasing of gas temperature before DPF, the heat from soot combustion can be used. The preliminary studies show a possibility of using the special design of DPF with heat recovery system. The paper presents results obtained from simulations based on one-dimensional model of such system and analysis of increasing the heat recovery ratio by change of geometry of DPF. The gas heat exchange formulas between DPF and the heat exchange model are partly included in the paper. The preliminary results of calculations show the possibility of increase of exhaust gases in front of DPF about 20%, which enables a continuous regeneration of DPF. Heat recovery ratio is depends on soot combustion rate on the wall of DPF monolith. The method enables to recover some part of energy which is lost in the conventional DPF. The paper is a part of further work in European project FP6 IPSY.
Słowa kluczowe
EN diesel engines   exhaust emission   DPF  
Wydawca Institute of Aviation
Czasopismo Journal of KONES
Rocznik 2010
Tom Vol. 17, No. 1
Strony 273--281
Opis fizyczny Bibliogr. 8 poz., rys.
autor Mitianiec, W.
  • Cracow University of Technology Jana Pawia II Av. 37, 31-864 Kraków, Poland tel: +48 12 6283692, fax: +48 12 6283690,
[1] Bisset, E. J., Shadman, F., Thermal regeneration of Diesel Particulate Monolithic Filters, AIChE Journal, Vol. 31, No. 5, pp. 753-758.
[2] Huynh, C. T., Johnson, J., Yang, S. L., Bagley, S., Warner, J., A One-Dimensional Computational Model for Studying and Regeneration Characteristics of a Catalyzed Wall-Flow Diesel Particulate Filter, SAE 2003-01-0841, SP-1755, SAE World Congress, Detroit 2003.
[3] Konstandopoulos, A., Kostoglou, M., Housiada, P., Vlachos, N., Zarvalis, D., Mulichannel Simulation o Soot Oxidation in Diesel Particulate Filters, SAE 2003-01-0839, SP-1755, SAE World Congress,Detroit 2003.
[4] Konstandopoulos, A. G et al, Fundamental studies of diesel particulate filters. Transient loading regeneration and aging, SAE Paper No. 2000-0101016.
[5] Mitianiec, W., Simulation of heat recovery in diesel particle filter, Combustion Engines, 2009-SC-045, pp. 121-127, Bielsko-Biała 2009.
[6] Nagórski, Z., Teodorczyk, A., Bernhardt, M., Regeneracja samochodowych filtrów spalin. Tendencje rozwojowe, modelowanie, badania symulacyjne, Politechnika Warszawska, Warszawa 2003.
[7] Nakatani, K. et al, Simultaneous PM and NOx reduction system for diesel engines, SAE Paper 2002-01-0957.
[8] Walter, B. B., Gatellier, B., Near Zero NOx Emissions and High Fuel Efficiency Diesel Engine: the NADITM Concept Using Dual Mode Combustion, Oil & Gas Science and Technology – Rev. IFP, Vol. 58, No. 1, pp. 101-114, 2003.
Kolekcja BazTech
Identyfikator YADDA bwmeta1.element.baztech-article-BUJ5-0030-0083