Powiadomienia systemowe
- Sesja wygasła!
- Sesja wygasła!
Tytuł artykułu
Treść / Zawartość
Pełne teksty:
Identyfikatory
Warianty tytułu
Powłoki Fe-Al osadzane detonacyjnie. Część III: budowa warstw pośrednich Ni(Cr) I Ni(Al) oraz powłoki Fe-Al na podłożu stali węglowej osadzanych detonacyjnie
Języki publikacji
Abstrakty
The morphology of interlayars and the coating of Fe-Al phase detonation sprayed (DGS) on the substrate of 045 steel was analysed in the work. The Ni(Al) layer, first from the substrate side consisted of Ni with inclusions of Al oxide. The second deposited layer was Ni(Cr), which contained lamellas of Cr in the Ni matrix. The phases present in the transition layers and in the coating were identified with SEM, and EDX methods (linear and point changes of chemical composition). The identification was confirmed with the X-ray technique and TEM microstructure analysis. It was established that Al oxides and AlNiO phases appeared in the DGS process after partial melting and oxidation of Al particles, while in the not melted part of grains small grain morphology was observed. Using the X-ray method, the FeAl2O4, Fe3Al and FeAl phases were identified in the coating, the Cr and Cr2Ni3 phase in the Ni(Cr) interlayer as well as pure nickel and the NiAl phase in the Ni(Al) interlayer. The occurrence of brittle phases of Al oxide and AlNiO phases near the boundaries of layers might result in the increase of tendency to delamination. Hence the reduction of the Al content seems advantageous from the point of view of mechanical properties of the joint.
W pracy poddano analizie metodą skaningowej - SEM i transmisyjnej- TEM mikroskopii elektronowej, budowę warstw pośrednich i powłokę faz typu Fe-Al natryskiwanych detonacyjnie (DGS) na podłoże stali 045. Warstwa Ni(Al) pierwsza od podłoża składa się z niklu z wtrąceniami Al i tlenku glinu. Na niej osadzona jest warstwa druga Ni(Cr) składającą się z warstewek chromu w osnowie niklu. Metodami EDX, liniowej zmiany składu oraz punktowej analizy zidentyfikowano fazy w warstwach pośrednich i powłoce. Tą identyfikację potwierdzono techniką X-ray oraz analizą mikrostruktury TEM. Ustalono, że tlenki oraz AlNiO fazy powstały w procesie DGS po nadtopieniu i utlenieniu cząstek Al, zaś w nie nadtopionej części ziaren zaobserwowano drobnoziarnistą budowę. W powłoce zidentyfikowano metodą X-ray fazy: FeAl2O4, Fe3Al oraz FeAl, w warstwie pośredniej Ni(Cr) - chrom i fazę Cr2Ni3w osnowie niklu, zaś w warstwie Ni(Al) czysty nikiel i fazę NiAl. Występowanie faz tlenku glinu i faz AlNiO w pobliżu granic warstw pośrednich powodować może zwiększenie tendencji do delaminacji. Korzystnym byłoby zatem obniżenie ilości aluminium.
Wydawca
Czasopismo
Rocznik
Tom
Strony
262--269
Opis fizyczny
Bibliogr. 7 poz., rys., tab.
Twórcy
autor
autor
autor
autor
autor
- Materials Science Polish Academy of Sciences, Institute of Metallurgy, 30-059 Krakow, 25 Reymonta Str., Poland
Bibliografia
- [1] E. Kadyrov, V. Kadyrov, Advanced Materiale & Processes 8, 21 (1995).
- [2] J. M. Guilemy, C. R. C. Lima, N. Cinca, J. Ruface, Coating Technology 201, 2073 (2006).
- [3] C. Senderowski, Z. Bojar, A. Pawłowski, W. Wołczyński, International Conference EUROMAT, Glasgow, September 7-10 (2009).
- [4] C. Senderowski, Z. Komorek, Z. Bojar, A. Pawłowski, Inżynieria Materialowa 27, 1-4 (2009).
- [5] C. Senderowski, Z. Bojar, International Journal of Applied Mechanics and Engeenering 9, 65 (2004).
- [6] A. Pawłowski, C. Senderowski, W. Wołczyński, J. Morgiel, Ł. Major, Archives of Metallurgy and Materials 56, 1 (2011) in press.
- [7] C. Senderowski, A. Pawłowski, Z. Bojar, W. Wołczyński, M. Faryna J. Morgiel, Ł. Major, Archives of Metallurgy and Materials 55(2) 373-381 (2010).
Typ dokumentu
Bibliografia
Identyfikator YADDA
bwmeta1.element.baztech-article-BSW3-0091-0006