Modification of robust filtering of stratified surface topography

• Autorzy: Dobrzański P. , Pawlus P.
• Języki publikacji: EN

Abstrakty

EN

Various components of surface texture are identified, namely form, waviness and roughness. Separation of these components is done by digital filtering. Several problems exist during analysis of two-process surfaces. Therefore the Gaussian robust profile filtering technique was established and has been studied here. The computer generated 2D profiles and 3D surface topographies having triangular scratches as well as measured stratified surfaces were subjected to filtration. However even robust filter applications cause distortion of profiles having valleys wider than 100 ěm. In order to minimize the distortion associated with wide and deep valleys, the robust filter should be modified. A special procedure was elaborated for minimizing distortion of roughness profiles caused by filtration. Application of this method to analyses of several profiles was presented. The difference between 1-D and 2-D filtering of surface topography using the same kind of filter was discussed. As a result we found that modification of a 2-D surface topography filter was not necessary.

Słowa kluczowe

EN

two-process surfaces; digital filtering; robust filter; valley suppression filter; modification of filter

• Wydawca: Komitet Metrologii i Aparatury Naukowej PAN
• Czasopismo: Metrology and Measurement Systems
• Rocznik: 2013
• Tom: Vol. 20, nr 1
• Strony: 107--118
• Opis fizyczny: Bibliogr. 24 poz., rys., tab., wykr.

Twórcy

autor

Dobrzański P.

autor

Pawlus P.

• Rzeszow University of Technology, Faculty of Management, Powstańców Warszawy 8, 35-959 Rzeszów, Poland,

Bibliografia

• [1] Raja, J., Muralikrishnan B., Fu, S. (2002). Recent advances in separation of roughness, waviness and form. Precision Engineering, 26, 222-235.
• [2] Brinkmann, S., Bodschwinna, H. (2003). Advanced Gaussian filters. Advanced Techniques for Assessment Surface Topography. Kogan Page Science, London and Sterling, 62-89.
• [3] Brinkmann, S., Bodschwinna, H., Lemke, H.-W. (2000). Development of a robust Gaussian regression filter for three-dimensional surface analysis. X International Colloquium on Surfaces, Chemnitz, Germany, 122-131.
• [4] Pawlus, P. (1998). Digital filtering of the surface texture measurement on inner cylindrical surfaces. Measurement, 24, 139-159.
• [5] Whitehouse, D.J. (1983). Some theoretical aspects of a practical measurement problem in plateau honing. Int. J. Prod. Res., 21(2), 215-221.
• [6] Mummery, L. (1992). Surface Texture Analysis - the Handbook. Hommelwerke GmbH.
• [7] Hampel, F.R., Ronchetti, E.M., Rousseeuw, P.J., Stahel, W.A. (1985). Robust Statistics. J. Wiley & Sons, New York.
• [8] Li, H., Jiang, X., Li, Z. (2004). Robust estimation in Gaussian filtering for engineering surface characterization. Precision Engineering, 28, 186-193.
• [9] Seewig, J. (2005). Linear and robust gaussian regression filters. ISTM II Conference. Huddersfield 2, UK, 248-251.
• [10] Langholz, N., Seewig, J., Reithmeier, E. (2007). Robust surface fitteing with using weights based on a priori knowledge about the measurement process. 11th International Conference on Metrology and Properties of Engineering Surfaces, Huddersfield, UK, 55-50.
• [11] Li, H., Cheung, C.F., Jiang, X.Q., Lee, W.B., To, S. (2006). A novel robust Gaussian filtering method for the characterization of surface generation in ultra-precision machining. Precision Engineering, 30(4), 421-443.
• [12] Dobrzański, P., Pawlus, P. (2010). Digital filtering of surface topography: Part II. Applications of robust and valley suppression filters. Elsevier, Precision Engineering-Journal of the International Societies for Precision Engineering and Nanotechnology, 34, 651-658.
• [13] Dobrzański, P. (2008). Elaboration and verification of filtering algorithms in surface topography analysis. PhD. Thesis. Poznan University of Technology, Poznań.
• [14] Radhakrishnan, V. (1972). Selection of an envelope circle radius for E-system roughness measurement. Int. J. Mach. Tools Des. & Res., 12, 151-159.
• [15] Whitehouse, D.J. (1985). Assessment of surface finish profiles produced by multi-process manufacture. In Proc. of the Inst. Mech. Engrs, 199(4), 263-270.
• [16] Torrance A.A. (1997). A simple datum for measurement of the Abbott curve of a profile and its first derivative. Tribology International, 30(3), 239-244.
• [17] Boulanger, J. (1992). The MOTIFS-method - An interesting complement to ISO-parameters for some functional problems. Int. J. Mach. Tools Manufact., 32(1/2) 203-209.
• [18] Zahouani, M. (1997). Spectral and 3D motifs identification of anisotropic topographical components. Analysis and filtering of anisotropic patterns by morphological rose approach. In Proc. of 7th Int. Conf. on Metrology and Properties of Engineering Surfaces, Goteborg, Sweden, 222-230.
• [19] Scott, P.J. (2000). Scale-space technique. X International Colloquium on Surfaces, Chemnitz, Germany, 1531-61.
• [20] Krystek, M. (2004). Morphological filters in surface texture analysis. XI International Colloquium on Surfaces, Chamnitz, Germany, 43-55.
• [21] Chen, X., Raja, J., Simanapalli, S. (1994). Multi-scale analysis of engineering surfaces. In Proc. of 6th Int. Conf. Metrology and Properties of Eng. Surfaces, Birmingham, UK, 231-239.
• [22] Fu, S., Muralikrishnan, B., Raja, J. (2003). Engineering surface analysis with different wavelet bases. ASME Journal of Manufacturing Science and Engineering, 125(4), 844-852.
• [23] Jiang, X., Scott, P.J., Whitehouse, D.J., Blunt, L. (2007). Paradigm shift in surface metrology. Part II. The current shift. In Proc. R. Soc. A., 463, 2071-2099.
• [24] Mendeleyev, V.A. (1997). Dependence of measuring errors of rms roughness on stylus tip size for mechanical profilers. Applied Optics, 36(34), 9005-9009.