Grooved roll for a high speed twin roll caster

• Autorzy: Haga T. , Hirooka K. , Watari H. , Kumai S.
• Języki publikacji: PL

Abstrakty

EN

Purpose: Purpose of this paper is investigation of the effect of roll-surface on the strip-surface. Improvement of small cracks on the strip-surface was tried and effect of groove at the roll surface on the strip surface was shown. Design/methodology/approach: Method used in the present study was high speed twin roll caster with grooved roll. Two kinds of grooves were used: one was parallel groove and the other was cross groove machined by knurling and bite attached to a lathe. Findings: Findings of this research are that grooved roll was effective to eliminate the small cracks on the strip surface. The contact condition between the roll and the melt became uniform by the small groove on the roll surface. Contact area became small, and heat transfer between the melt and roll became small, too. As the result, chill structure did not become columnar, and crack did not occur. Groove pattern on the strip surface could be erased by the cold rolling. Research limitations/implications: Research limitation is that groove life could not be investigated. Practical implications: Practical implications are as below. The roll load was small and strip was not hot-rolled in a high speed twin roll caster. The grooved roll made strip-surface sound. Grooved 600mm width roll was tested, and usefulness of the grooved roll was shown. Originality/value: In the present study effect of the grooved roll on a high speed twin roll caster was investigated.

Słowa kluczowe

PL

karoseria

EN

casting; twin roll caster; grooved roll; roll surface

• Wydawca: International OCSCO World Press
• Czasopismo: Archives of Materials Science and Engineering
• Rocznik: 2008
• Tom: Vol. 30, nr 2
• Strony: 117--120
• Opis fizyczny: Bibliogr. 17 poz.

Twórcy

autor

Haga T.

autor

Hirooka K.

autor

Watari H.

autor

Kumai S.

Bibliografia

• [1] R. Cook, P.G. Groock, P.M. Thomas, D.V. Edmonds, J.D. Hunt, Development of the twin-roll casting process, Journal of Materials Processing Technology 55 (1995) 76-84.
• [2] M. Cortes, Pechiney-Junmbo 3CM, The new demands of thin strip casting, Light Metals (1995) 1161-1164.
• [3] B. Taraglio, C. Romanowski, Thin-gage/high-speed roll casting technology for foil production, Light Metals (1995) 1165-1182.
• [4] A.I. Nussbaum, Three-state-of-the-art Thin-gage high-speed roll caster for aluminum alloy sheet products Part III, Light Metals Age 55 (1997) 34-39.
• [5] O. Daaland, A.B. Espedal, M.L. Nedreberg, I. Alvestad, Thin gage twin-roll casting, process capabilities and product quality, Light Metals (1997) 745-752.
• [6] P.Y. Menet, R. Cayol, J. Moriceau, Pechiney Jumbo 3CM ‘TM’ start-up of the Neu-Brisach thin strip caster, Light Metals (1997) 753-756.
• [7] P.M. Thomas, P.G. Grocock, J.M. Bouzendorffer, Dynamic strip caster-An update on the operation of the roll caster at Eurofoil, Metal Plant Technology Institute 20 (1997) 44-52.
• [8] S. Hamers, D. Smith, C. Romanowski, G. Yildizbayrak, B.Taraglio, Twin roll casting of aluminum at 2.5mm gauge. Production experience and process improvement, Light Metals (1999) 931-937.
• [9] J. Benedyk, Thin strip casting for aluminum alloy sheet applications developed by Pechiney at Neuf-Brisach, Light Metal Age 59 (2001) 28-30.
• [10] S. Hamer, C.Romanowski, B.Taraglio, Continuous casting and rolling of aluminum: Analysis of capacities, products ranges, and Technology, Light Metal Age, 60 (2002) 6-17.
• [11] M. Duendar, OE. Keles, B. Kerti, N. Dogan, Crystallographic texture development of twin-roll cast aluminum strips, Light Metal (2004) 723-724.
• [12] Ch. Gras, M. Meredith, J.D. Hund, Microdefects for mation during the roll casting of Al-Mg-Mn aluminum alloys, Journal of Materials Processing Technology 167 (2005) 62-72.
• [13] T. Haga, H. Watari, S. Kumai, High speed twin roll casting of Mg alloy strip by a vertical type twin roll caster, Journal of Achievements in Materials and Manufacturing Engineering 15 (2006) 186-192.
• [14] T. Haga, M. Ikawa, H. Watari, S. Kumai, High speed twin roll casting of Al-3Si-0.6Mg strip, Journal of Achievements in Materials and Manufacturing Engineering 17 (2006) 337-340.
• [15] T. Haga, M. Ikawa, H. Watari, S. Kumai, High speed twin roll casting of 6016 strip, Journal of Achievements in Materials and Manufacturing Engineering 18 (2006) 371-374.
• [16] T. Haga, M. Ikawa, H. Watari, S. Kumai, High speed twin roll casting of recycled Al-3Si-0.6Mg strip, Journal of Achievements in Materials and Manufacturing Engineering 21/1 (2007) 7-12.
• [17] T. Motegi, N. Ogawa, Continuous casting of semisolid Al-Si- Mgalloy, Proceedings of the International Conference on Aluminum Alloys”ICAA-6” Toyohashi Japan, 1998, 297-326.