PL EN


Preferencje help
Widoczny [Schowaj] Abstrakt
Liczba wyników
Tytuł artykułu

Fabrication and characterization of TiAl/Ti3Al-based intermetallic composites (IMCs) reinforced with ceramic particles

Wybrane pełne teksty z tego czasopisma
Identyfikatory
Warianty tytułu
Języki publikacji
EN
Abstrakty
EN
Purpose: The purpose of the paper is to fabricate and characterise TiAl/Ti₃Al-based intermetallic composites (IMCs) reinforced with ceramic particles. Design/methodology/approach: Composites were formulated by blending commercially available powders of either TiAl or Ti₃Al (technical grade with traces of Al and Ti) with ceramic powders (B₄C, TiC or TiB₂) in appropriate amounts to create titanium aluminide-based matrices with 10, 20, 30, 40 and 50 vol. % of B₄C, TiC or TiB₂ discontinuous reinforcement. The powder blends were thoroughly mixed and subsequently cold compacted. Findings: Qualitative metallographic analysis of the as-densified microstructures confirmed that during densification of the composite matrix both TiAl and Ti₃Al single phase titanium aluminide powders were transformed into various intermetallic phases (TiAl, Ti₃Al and TiAl₃). Regarding the room temperature tensile properties, excellent tensile strength, tensile yield strength and Young's modulus were measured in all fully dense composite samples, irrespective of their phase composition and volume fraction of reinforcement. Research limitations/implications: Generally, the improvement of tensile strength, tensile yield strength and Young's modulus was found to be correlated with increase in the amount of ceramic reinforcement in the matrix. However, quite the opposite behaviour was found regarding elongation, where the introduction of ceramic particles into the intermetallic matrix led in all specimens to a significant reduction of elasticity. Originality/value: In all systems and compositions, fully dense composite samples (with a retained porosity less than 1 vol. %) were successfully obtained, revealing the significant industrial potential of this fabrication method.
Słowa kluczowe
EN
PL
Rocznik
Strony
75--83
Opis fizyczny
Bibliogr. 26 poz.
Twórcy
autor
Bibliografia
  • [1] Gamma Titanium Aluminide 1999, TMS, Warrendale, PA, 1999, 3.
  • [2] S. Djanarthany, J.C. Viala, J. Bouix, An Overview of Monolithic Titanium Aluminides Based on Ti3Al and TiAl, Materials Chemistry and Physics 72 (2001) 301-319.
  • [3] C.M. Ward-Close, R. Minor, P.J. Doorbar, Intermetallic-matrix composites-a review, Intermetallics 4/3 (1996) 217-229.
  • [4] P.C. Brennan, W.H. Kao, J.M. Yang, The mechanical properties of an Al2O3/Ni3Al particulate-reinforced composite, Materials Science and Engineering A 153 (1992) 635-640.
  • [5] J.C. Rawers, W. Wrzesinski, Heat treatment of reaction-sintered hot-pressed TiAl, Scripta Metallurgica et Materialia 24/10 (1990) 1985-1990.
  • [6] H.Y. Sohn. X. Wang, Mathematical and experimental investigation of the self-propagating high-temperature synthesis (SHS) of TiAl3 and Ni3Al intermetallic compounds, Journal of Materials Science 31 (1996) 3281-3288.
  • [7] G.H. Wang, M. Dahms, An effective method for reducing porosity in the titanium aluminide alloy Ti52Al48 prepared by elemental powder metallurgy, Scripta Metallurgica et Materialia 26/9 (1992) 1469-1474.
  • [8] G.X. Wang, M. Dahms, G. Leitner, S. Schultrich, Titanium aluminides from cold-extruded elemental powders with Al-contents of 25-5 at% Al, Journal of Materials Science 29 (1994) 1847-1853.
  • [9] T.W. Lee, C.H. Lee, The Effect of Heating Rate on the Reactive Sintering of Ti-48%Al Elemental Powder Mixture, Journal of Materials Science Letters 17/16 (1998) 1367-1370.
  • [10] G.X. Wang, M. Dhams, Powder Metallurgy International 24 (1992) 219.
  • [11] G. Leitner, M. Dhams, W. Poeβnecker, B. Wildhagen, Proceedings of International Conference "P/M Aerospace Materials 1991", MPR Publishing Services Ltd, Shrewsbury, 1992.
  • [12] F.J.J. Van Loo, G.D. Rieck, Diffusion in the titanium-aluminium system -I. Interdiffusion between solid Al and Ti or Ti-Al alloys Acta Metallurgica 21 (1973) 61-71.
  • [13] M. Dahms, Formation of titanium aluminides by heat treatment of extruded elemental powders, Materials Science and Engineering A 110 (1989) L5-L8.
  • [14] W. Misiolek, R.M. German, Reactive sintering and reactive hot isostatic compaction of aluminide matrix composites, Materials Science and Engineering A 144/1-2 (1991) 1-10.
  • [15] G.X. Wang, M. Dahms, Reaction sintering of cold- extruded, Metallurgia Translation A 24 (1993) 1517.
  • [16] J.C. Rawers. W.R. Wrzesinski, Reaction-sintered hot-pressed TiAl, Journal of Materials Science 27 (1992) 2877-2886.
  • [17] K. Taguchi, M. Ayada, K.N. Isihara, P.H. Shingu, Near-net shape processing of TiAl intermetallic compounds via pseudo HIP-SHS route, Intermetallics 3/2 (1995) 91-98.
  • [18] H.E. Maupin, J.C. Rawers, TiAl composites formed from elemental powders by hot-isostatic pressing processing, Journal of Materials Science Letters 12 (1993) 165-167.
  • [19] H.E. Maupin, J.C., Metal- intermetallic composites formed by reaction-sintering elemental powders, Journal of Materials Science Letters 12 (1993) 540-541.
  • [20] R.G. Rowe, S.C. Huang, Recent developments in titanium aluminide, alloys Israel Journal of Technology 24/1-2 (1988) 255-260.
  • [21] K.S. Chan. Y.W. Kim, Influence of microstructure on crack-tip micromechanics and fracture behaviours of a two-phase TiAl alloy, Metallurgical Transactions A 23 (1992) 1663-1677.
  • [22] M. Grujicic, G. Cao, Crack Growth in Lamellar Titanium Aluminides Containing Dispersed Beta Phase Precipitates, Journal of Materials Science 37/14 (2002) 2949-2963.
  • [23] M. Sujata, S. Bhabgava. S. Sangal, On the formation of TiAl3 during reaction between solid Ti and liquid Al, Journal of. Materials Science Letters 16 (1997) 1175-1178.
  • [24] A.J. Pyzik. D.R. Beaman, Al-B-C Phase Development and Effects on Mechanical Properties of B4C/Al-Derived Composites, Journal of American Ceramic Society 78 (1995) 305-312.
  • [25] J. Jung, Kang, Advances in Manufacturing Boron Carbide- Aluminum Composites, Journal of American Ceramic Society 87 (2004) 47.
  • [26] A. Banjeri,W. Reif, Development of Al-Ti-C grain refiners containing TiC, Metallurgical and Materials Transactions A 17 (1986) 2127.
Typ dokumentu
Bibliografia
Identyfikator YADDA
bwmeta1.element.baztech-article-BSL8-0031-0020
JavaScript jest wyłączony w Twojej przeglądarce internetowej. Włącz go, a następnie odśwież stronę, aby móc w pełni z niej korzystać.