Clad strip casting by a twin roll caster

• Autorzy: Haga T. , Nakamura R. , Kumai S. , Watari H.
• Języki publikacji: EN

Abstrakty

EN

Purpose: Of this paper is to realize the casting of the clad strip by only one process. Therefore, the investigation of the ability of the casting of the clad strip by a vertical type twin roll caster was operated. The aim of the use of the twin roll caster to make clad strip was in the reduction of the production-energy of the clad strip. Design/methodology/approach: Used in the present study was a vertical type twin roll caster with the scriber. The scriber was used to prevent the mixture of the two kinds of the melts. The scriber was set at roll-bite, and the scriber contacted to the one of solidification layer. The melt was stopped by the scriber and the only the solidification layer was dragged by the roll. Findings: The clad strip with the clear interface could be by the vertical type twin roll caster with the scriber. The scriber was useful to drag only the solid and semisolid layer. The two kinds of strips were connected strictly at the interface of the clad strip. The clad strip was not broken at the interface by the continuous bending. Research limitations/implications: Are that 100 mm width-strip was cast in the present study. Ability of the clad strip that is wider than 100 mm was not clear. The control of the clad ratio was not investigated. Practical implications: The twin roll caster devised and investigated in this report is useful to cast clad strip like the brazing sheet for the radiator of the automobile. Originality/value: The vertical type twin roll cater to cast clad strip is original process. The scriber was used to prevent the mixture of the two kinds of melts. The scriber was not used in the previous research to cast clad strip at the twin roll caster, and use of the scriber was the first try.

Słowa kluczowe

EN

casting; twin roll caster; clad strip; interface clad strip

PL

odlewanie; odlewanie techniką szybkiego schładzania z fazy ciekłej; taśma warstwowa

• Wydawca: International OCSCO World Press
• Czasopismo: Archives of Materials Science and Engineering
• Rocznik: 2009
• Tom: Vol. 37, nr 2
• Strony: 117--124
• Opis fizyczny: Bibliogr. 20 poz.

Twórcy

autor

Haga T.

autor

Nakamura R.

autor

Kumai S.

autor

Watari H.

• Osaka Institute of Technology, 5-16-1 Omiya Asahiku Osakacity, 535-8585 Japan,

Bibliografia

• [1] T. Haga, S.Suzuki, A twin roll caster to casting of clad strip, Journal of Materials Processing and Technology 138 (2003) 366-371.
• [2] T. Haga, K. Takahashi, Downward melt drag twin roll caster, Journal of Materials Processing and Technology 157 (2004) 696-700.
• [3] T. Haga, Casting of clad strip using a twin roll caster, Proceeding of the 33rd International Matador Conference Matador, 2000, 295-300.
• [4] R. Cook, P.G. Groock, P.M. Thomas, D.V. Edmonds, J.D. Hunt, Development of the twin-roll casting process, Journal of Materials Processing Technology 55 (1995) 76-84.
• [5] M. Cortes, Pechiney-Junmbo 3CM, The new demands of thin strip casting, Light Metals (1995) 1161-1164.
• [6] B. Taraglio, C. Romanowski, Thin-gage/high-speed roll casting technology for foil production, Light Metals 5 (1995) 1165-1182.
• [7] A.I. Nussbaum, Three-state-of-the-art Thin-gage high-speed roll caster for aluminum alloy sheet products Part B, Light Metals Age 55 (1997) 34-39.
• [8] O. Daaland, A.B. Espedal, M.L.Nedreberg, I. Alvestad, Thin gage twin-roll casting, process capabilities and product quality, Light Metals 4 (1997) 745-752.
• [9] P.Y. Menet, R. Cayol, J. Moriceau, Pechiney Jumbo 3CM ‘TM’ start-up of the Neu-Brisach thin strip caster, Light Metals 6 (1997) 753-756.
• [10] P.M. Thomas, P.G. Grocock, J.M. Bouzendorffer, Dynamic strip caster-An update on the operation of the roll caster at Eurofoil, Metall Plant Technology International 20 (1997) 44-52.
• [11] S. Hamers, D. Smith, C. Romanowski, G. Yildizbayrak, B. Taraglio, Twin roll casting of aluminum at 2.5mm gauge. Production experience and process improvement, Light Metal 7 (1999) 931-937.
• [12] J. Benedyk, Thin strip casting for aluminum alloy sheet applications developed by Pechiney at Neuf-Brisach, Light Metal Age 59 (2001) 28-30.
• [13] S. Hamer, C. Romanowski, B. Taraglio, Continuous casting and rolling of aluminum: Analysis of capacities, products ranges, and Technology, Light Metal Age 60 (2002) 6-17.
• [14] M. Duendar, OE. Keles, B. Kerti, N. Dogan, Crystallo-graphic texture development of twin-roll cast aluminum strips, Light Metal 13 (2004) 723-724.
• [15] Ch. Gras, M. Meredith, J.D. Hund, Microdefects for mation during the roll casting of Al-Mg-Mn aluminum alloys, Journal of Materials Processing Technology 167 (2005) 62-72.
• [16] T. Haga, H. Watari, S. Kumai, High speed twin roll casting of Mg alloy strip by a vertical type twin roll caster, Journal of Achievements in Materials and Manufacturing Engineering 15 (2006) 186-192.
• [17] T. Haga, M. Ikawa, H.Watari, S.Kumai, High speed twin roll casting of Al-3Si-0.6Mg strip, Journal of Achievements in Materials and Manufacturing Engineering 17 (2006) 337-340.
• [18] T. Haga, M. Ikawa, H. Watari, S. Kumai, High speed twin roll casting of 6016 strip, Journal of Achievements in Materials and Manufacturing Engineering 18 (2006) 371-374.
• [19] T. Haga, M. Ikawa, H. Watari, S. Kumai, High speed twin roll casting of recycled Al-3Si-0.6Mg strip, Journal of Achievements in Materials and Manufacturing Engineering 19/1 (2007) 7-12.
• [20] T. Haga, K. Hirooka, H. Watari , S. Kumai, Grooved roll for a high speed twin roll caster, Archives of Materials Science and Engineering 30/2 (2008) 117-120.