Parameters of the two-phase sand-air stream in the blowing process

• Autorzy: Dańko J. , Dańko R. , Burbelko A. A. , Skrzyński M.
• Języki publikacji: EN

Abstrakty

EN

Theoretical problems concerning the determination of work parameters of the two-phase sand-air stream in the cores making process by blowing methods as well as experimental methods of determination of the main and auxiliary parameters of this process decisive on the cores quality assessed by the value and distribution of their apparent density are presented in the paper. In addition the results of visualisations of the core-box filling with the sand-air stream, from the blowing chamber, obtained by the process filming by means of the quick-action camera are presented in the paper and compared with the results of simulation calculations with the application of the ProCast software.

Słowa kluczowe

EN

foundry cores; blowing processes; shooting processes; experimental investigations; simulation calculations

PL

rdzeń odlewniczy; badania eksperymentalne; obliczenia symulacyjne

• Wydawca: Komisja Odlewnictwa Polskiej Akademii Nauk Oddział w Katowicach
• Czasopismo: Archives of Foundry Engineering
• Rocznik: 2012
• Tom: Vol. 12, iss. 4
• Strony: 25--30
• Opis fizyczny: Bibliogr. 14 poz., rys., wykr.

Twórcy

autor

Dańko J.

autor

Dańko R.

autor

Burbelko A. A.

autor

Skrzyński M.

• AGH - University of Science and Technology, Faculty of Foundry Engineering, Reymonta 23 str., 30-059 Kraków, Poland,

Bibliografia

• [1] Aksjonow P. N. (1965). Wybrane zagadnienia z teorii maszyn odlewniczych. Katowice: "Śląsk" Publishing House.
• [2] Boenisch D., Knauf M. (1991). Kernschiessen - Untersuchungen mit neuartigen Prüfkörpern und verschiedenen Kernbindern . Giesserei 18, 640-646.
• [3] Dańko J. (1992). Teoretyczna i doświadczalna weryfikacja modelu Aksjonowa obliczania maszyn dmuchowych. Archiwum Technologii Budowy Maszyn 10, 7-15.
• [4] Dańko J., Dańko R. (2009). Assessment of Core Sand suitability for filling the core-box and for compaction. Archives of Foundry Engineering 9(1), 37-40.
• [5] Dańko J, Zych J., Dańko R. (2009). Diagnostic methods of technological properties and casting cores quality. Archives of Metallurgy and Materials 54(2), 381-392.
• [6] Dańko J., Dańko R.(2010). Effective cross-section area of a shooting valve in core shooting machines. Archives of Foundry Engineering 10(1), 243-246.
• [7] Dańko J., Zych J., Dańko R., Sroczyński A. (2006). Badania struktury rozkładu gęstości masy w rdzeniach wykonanych za pomocą wstrzeliwania. Archives of Foundry 6 (22), 133-138.
• [8] Dańko J., Zych J., Dańko R. (2009). Diagnostic methods of technological properties and casting cores quality. Archives of Metallurgy and Material 54(2), 281-392.
• [9] Dańko J. (1995). An effect of the venting system on the core box filling ratio and the apparent core density structure. Przegląd Odlewnictwa 3, 85-92.
• [10] Reek R. (2005). Optimierung des Füll-und Hartungsvorgangs von Giessereisandkernen durch 3-D Simulation der Strömungsvorgänge. Giessereiforschung 57(3), 2-14.
• [11] Vidal V.,Beauvais P., Leger-Delcourt E., Hossemand J.S., Sadon P. (2005): Pressure distribution during core production I core blowing machines. Fonderie Fondeur D'Aujourd'Hui, 241, 12-20.
• [12] Walker M., Palczenski S., Snider D., Williams K. (2002). Modeling Sand Core Blowing: Simulation's Next Challenge. Modern Casting, April, 41-43.
• [13] Winartomo B., Vroomen U., Buhrig-Polaczek A., Pelzer M (2006). Multiphase modelling od core shooting process. Interational Journal of Cast Metals Research. 18(1), 13-20.
• [14] Wu Junjiao, Cui Yi, Li Wenzhen (2001). A Study on Numerical Simulation of Core-Shooting Process. Journal of Material Science and Technology 17(6), 625-628.