PL EN


Preferencje help
Widoczny [Schowaj] Abstrakt
Liczba wyników
Tytuł artykułu

Correlation of specific ampere draw with rock brittleness indexes in rock sawing process

Wybrane pełne teksty z tego czasopisma
Identyfikatory
Warianty tytułu
PL
Korelacja określonego poboru mocy ze wskaźnikiem kruchości skał w procesie piłowania skał
Języki publikacji
EN
Abstrakty
EN
The aim of this study is to investigate the effect of the rock brittleness indexes on the specific ampere draw of the circular diamond saws. In this study, twelve rock types belonging to granite and carbonate rock were cut with two different types of circular diamond saws on a fully instrumented laboratory-sawing rig at different feed rate and depths of cut. Rock samples were collected from factories from Iran for laboratory tests and uniaxial compressive strength and tensile strength were determined. The brittleness of B1 (the ratio of compressive strength to tensile strength), B2 (the ratio of compressive strength minus tensile strength to compressive strength plus tensile strength), and B3 (the area under line in relation to compressive strength and tensile strength) were evaluated. The relations between specific ampere draw and rock brittleness indexes were investigated using simple regression analysis. The results show that, there is no strong correlation between the specific ampere draw values and the brittleness of B1 and B2 values in carbonate rocks but there is a strong correlation between specific ampere draw and B3 while the specific ampere draw values of granite rocks are strongly correlated with all of brittleness indexes. It was concluded that the specific ampere draw values of granite and carbonate rocks can be reliably predicted by brittleness indexes and brittleness of B3, respectively.
PL
Celem badania jest przeanalizowanie wpływu wskaźników kruchości skał na określony pobór mocy diamentowych pił tarczowych. Dwanaście rodzajów skał granitowych i węglanowych piłowano przy pomocy dwóch różnych typów diamentowych pił tarczowych przy różnych prędkościach podawania i głębokościach cięcia w warunkach laboratoryjnych. Próbki skał zebrano z irańskich fabryk na potrzeby testów laboratoryjnych, podczas których określono wytrzymałość na ściskanie jednoosiowe i rozciąganie. Oceniono kruchość B1 (stosunek wytrzymałości na ściskanie do wytrzymałości na rozciąganie), B2 (stosunek różnicy wytrzymałości na ściskanie i wytrzymałości na rozciąganie do sumy wytrzymałości na ściskanie i wytrzymałości na rozciąganie) i B3 (obszar pod linią w relacji do wytrzymałości na ściskanie i wytrzymałości na rozciąganie). Relacje pomiędzy określonymi poborami mocy i wskaźnikami kruchości skał zostały zbadane z zastosowaniem prostej analizy regresyjnej. Wyniki wskazują, że nie zachodzi silna korelacja pomiędzy określonymi wartościami poboru mocy, a kruchością wartości B1 i B2 w skałach węglanowych, ale zachodzi silna korelacja między określonym poborem mocy, a B3. Określone wartości poboru mocy dla skał granitowych są silnie skorelowane ze wszystkimi wskaźnikami kruchości. Wyciągnięto wniosek, że określone wartości poboru mocy dla skał granitowych i węglanowych można z dużą dokładnością przewidzieć odpowiednio za pomocą wskaźników kruchości i kruchości B3.
Rocznik
Strony
777--788
Opis fizyczny
Bibliogr. 55 poz., rys., tab., wykr.
Twórcy
autor
autor
autor
autor
Bibliografia
  • Altindag R., 1997. The analysis of usability for the purposes of excavation mechanics of rock brittleness measurements. Dissertation, Osmangazi University.
  • Altindag R., 2000a. An analysis of brittleness on percussive drilling. J. of Geosound, December, no. 37, 167-170.
  • Altindag R., 2000b. The role of rock brittleness on analysis of percussive drilling performance. (in Turkish), Proceedings of 5th National Rock Mech., Symposium, Isparta, 105-112.
  • Altindag R., 2002. The evaluation of rock brittleness concept on rotary blast holes drills. J. of The South Afr. Inst. Of Min. Metall., Jan.-Feb, 61-66.
  • Altindag R., 2003. Correlation of specific energy with rock brittleness concepts on rock cutting. The Journal of The South African Institute of Mining and Metallurg., 163-172.
  • Atici U., Ersoy A,. 2009. Correlation of specific energy of cutting saws and drilling bits with rock brittleness and destruction energy. Journal of Materials Processing Technology, 209, 2602-2612.
  • Baron L.I., Loguntsov B.M., Posin E.Z., 1962. Determination of properties of rocks. (in Russian), NTILGD, p. 232, Gozgotekhizdat, Moscow.
  • Becker H., Lemmes F., Schommer M., 1984. Testing of rock mechanics as a basis for improved cutting technology. Glückauf + Translation, 120, no. 8, 122-124.
  • Birle J.D., Ratterman E., 1986. An approximate ranking of the sawability of hard building stones based on laboratory tests. Dimensional Stone Magazine, July-August, 3-29.
  • Buyuksagis I.S., 2007. Effect of cutting mode on the sawability of granites using segmented circular diamond sawblade. Journal of Materials Processing Technology, 183, 399-406.
  • Burgess R.B., 1978. Circular sawing granite with diamond saw blades. In: Proceedings of the Fifth Industrial Diamond Seminar, 3-10.
  • Clausen R., Wang C.Y., Meding M., 1996. Characteristics of acoustic emission during single diamond scratching of granite. Industrial Diamond Review, 3, 96-9.
  • Coates D.F., 1966. Experimental criteria for classification of rock substances. Int. J. Rock Mech. Min. Sci., 3, 181-189.
  • Copur H., 1999. Theoretical and Experimental studies of rock cutting with Drag bits towards the development of a performance prediction model for roadheaders. Ph.D. Thesis, Colorado School of Mines, p. 362.
  • Copur H., Tuncdemir H., Balci C., Ozturk C.A.. 2001. A brittleness concept based on indentation tests for assessment of rock cuttability. Proceedings of 10th Int. Symp. on Mine Planning and Equipment Selection, New Delhi, Nov., 19-21.
  • Delgado N.S, Rodriguez R, Rio A., Sarria I.D, Calleja L., Argandona V.G.R., 2005. The influence of microhardness on the sawability of Pink Porrino granite (Spain). International Journal of Rock Mechanics & Mining Sciences, 42, 161-6.
  • International Society for Rock Mechanics., 1981. Rock characterisation, testing and monitoring: ISRM suggested methods. Oxford: Pergamon.
  • Ersoy A., Atici U., 2004. Performance characteristics of circular diamond saws in cutting different types of rocks, Diamond Relat. Mater. 13, 22-37.
  • Ersoy A., Buyuksagis S., Atici U., 2005. Wear characteristics of circular diamond saws in the cutting of different hard and abrasive rocks. Wear 258, 1422-1436.
  • Evans I., Pomeroy C.D., 1966. The strength, fracture and workability of coal. Pergamon Press.
  • Eyuboglu A.S., Ozcelik Y., Kulaksiz S., Engin I.C., 2003. Statistical and microscopic investigation of disc segment wear related to sawing Ankara andesites. Int. J. Rock Mech. Min. Sci. 40, 405-414.
  • Fener M., Kahraman S., Ozder M.O., 2007. Performance Prediction of Circular Diamond Saws from Mechanical Rock Properties in Cutting Carbonate Rocks Rock Mech. Rock Engng. 40 (5), 505-517.
  • Glossary of Geology and Related Sciences, Amer. Geology. Inst., (1960), Washington D.C.
  • Goktan R.M., 1988. A theoretical and application analyses of the rock diggability. (in Turkish), Ph.D. Thesis, ITU Institute of Appl. Sciences, p. 108.
  • Goktan R.M., 1991. Brittleness and micro-scale rock cutting efficiency. Mining Science and Technology, 13, p. 237-241.
  • Goktan R.M., 1992. Applicability of rock brittleness ratio in percussive drilling performance. (in Turkish), Anadolu University, Journal of Eng. and Arch. Fac. 8, N.1, pp. 89-99.
  • Gunaydin O., Kahraman S., Fener M., 2004. Sawability prediction of carbonate rocks from brittleness indexes. J. South Afr. Inst. Min. Metall. 104, 239-244.
  • Hetenyi M. 1966. Handbook of Experimental Stress Analysis, p. 15, John Wiley, NewYork.
  • Hucka V., Das B., 1974. Brittleness determination of rocks by different methods. Int. J. Rock Mech. Min. Sci. Geomech. Abstr., 11, 389-392.
  • Inyang H.I., Pitt J.M., 1990. Standardisation of a percussive drill for measurement of the compressive strength of rocks. Rock Mech. Contributions and Challenges (Eds. Hustrulid and Johnson), 489-496.
  • Inyang H.I., 1991. Development of a preliminary rock mass classification scheme for near surface excavation. Int. J. Surface Min. and Reclamation, 5, 65-74.
  • Jennings M., Wright D., 1989. Guidelines for sawing stone, Industrial Diamond Review, 49, 70-75.
  • Kahraman S., 2002. Correlation of TBM and drilling machine performances with rock brittleness. Engineering Geology, 65(h), 269-283.
  • Kahraman S., Fener M., Gunaydin O., 2004. Predicting the sawability of carbonate rocks using multiple curvilinear regression analysis. International Journal of Rock Mechanics & Mining Sciences, 41, 1123-1131.
  • Kahraman S., Altun H., Tezekici B.S., Fener M., 2005. Sawability prediction of carbonate rocks from shear strength parameters using artificial neural networks. International Journal of Rock Mechanics & Mining Sciences, 43(1), 157-164.
  • Kahraman S., Ulker U., Delibalta S., 2007. A quality classification of building stones from P-wave velocity and its application to stone cutting with gang saws. J. South Afr. Inst. Min. Metall. 107, 427-430.
  • McFeat-Smith I., (1977). Rock property testing for the assessment of tunneling machine performance. Tunnels and Tunnelling, March, 23-33.
  • Mikaeil R., Ataei M., Hoseinie S.H., 2008. Predicting the production rate of diamond wire saws in carbonate rocks cutting. Industrial Diamond Review (IDR). 3, 28-34.
  • Mikaeil R., Yousefi R., Ataei M., Abasian Farani R., 2011. Development of a New Classification System for Assessing of Carbonate Rock Sawability. Archives of Mining Sciences, Vol. 56 (2011), No 1, p. 57-68.
  • Morley A., 1944. Strength of Material. Longman, Green, London. p. 35.
  • Obert L., Duvall W.I., 1967. Rock mechanics and the design of structures in rock. John Wiley, New York. p. 278.
  • Özçelik Y., Polat E., Bayram F., Ay A.M.. 2004. Investigation of the effects of textural properties on marble cutting with diamond wire. Int. J. Rock Mech. Min. Sci., Vol. 41, No. 3.
  • Özçelik Y., 2007. The effect of marble textural characteristics on the sawing efficiency of diamond segmented frame saws. Industrial Diamond Review, 2, 65-70.
  • Petoukhov I.M., Linkov A.M., 1983. Mechanics of rockburst and outburst. (in Russian), Moscow, Nedra.
  • Ramsey J.G., 1967. Folding and Fracturing of rocks. McGraw-Hill, London. p. 289.
  • Reichmuth R.D., 1968. Point load testing of brittle materials to determine tensile strength and relative brittleness. Proceedings of 9th Symp. Rock. Mech. Univ. of Colorado, 134-159.
  • Selmer-Olsen R., Blindheim D.T., 1970. On the drillability of rock by percussive drilling. Proceedings of 2nd Congress of the Int. Soc. for rock mechanics, Belgrade, 65-70.
  • Shimada H., Matsui K., 1994. Prediction of machine performance in mine tunnel drivage. Proceedings of mine planning and equipment selection Symp. 509-514.
  • Singh, P.S. (1986). Brittleness and the mechanical winning of coal, Min. Sci. and Tech., 3, 173-180.
  • Smoltczyk U., Gartung E., 1979. Geotechnical properties of a soft Keuper sandstone. Proc. 4th Congr. ISRM, Montreux, vol. 2, 639-644.
  • Stavroguin A.N., Protossenia A.G., 1985. Rock strength and excavation stability in great depth. (in Russian), Moscow, Nedra, p. 269.
  • Tonshoff H.K., Hillmann-Apmann H., Asche J., 2002. Diamond tools in stone and civil engineering industry: cutting principles, wear and applications. Diamond and Related Materials, 11, 736-741.
  • Tutmez B., Kahraman S., Gunaydin O., (2007). Multifactorial fuzzy approach to the sawability classification of building stones. Construction and Building Materials 21, 1672-1679.
  • Wei X., Wang C.Y., Zhou Z-H., 2003. Study on the fuzzy ranking of granite sawability. J. Mater. Process Technol. 139, 277-80.
  • Wright and Cassapi, 1985. Factors influencing stone sawability. Industrial Diamond Review, 2, 84-87.
Typ dokumentu
Bibliografia
Identyfikator YADDA
bwmeta1.element.baztech-article-BPZ5-0021-0054
JavaScript jest wyłączony w Twojej przeglądarce internetowej. Włącz go, a następnie odśwież stronę, aby móc w pełni z niej korzystać.