Experimental study of the dynamic characteristics and the optimization of spiral groove bearing spindles

• Autorzy: Zou Q.
• Języki publikacji: EN

Abstrakty

EN

In this researeh, an experimental test device of the spiral groove bearing (SGB) spindle is developed. The dynamic characteristics of the SGB spindle are investigated. The effects of rotating speed, load and bearing clearance on the dynamic characteristics are considered. lt is found that both radial and axial non-repeatable run out (NRRO) decrease with the increase of rotating speed of the spindle. The effeet of load on the radial NRRO is relatively smalI, but it has significant effect on the axial NRRO. With the decrease of axial bearing clearance, the radial and axial NRROs decrease. Based on the test results, the optimum parameters for the SGB spindle at different rotating speed are proposed, which include optimum load and bearing clearance, etc.

Słowa kluczowe

EN

spiral groove bearing; hard disc drive; non-repeatable run out; optimization

PL

mechanika; optymalizacja; łożysko

• Wydawca: Oficyna Wydawnicza Uniwersytetu Zielonogórskiego
• Czasopismo: International Journal of Applied Mechanics and Engineering
• Rocznik: 2005
• Tom: Vol. 10, no 4
• Strony: 731--740
• Opis fizyczny: Bibliogr. 10 poz., rys., tab., wykr.

Twórcy

autor

Zou Q.

• Department of Mechanical Engineering, Oakland University 2200 Squirrel Rd. Rochester, MI 48309, USA

Bibliografia

• [1] Bouchard G., Lau L. and Talke F.E. (1987): An investigation of nonrepeatable spindle run-out. - IEEE Transactions on Magnetics, vol.l23, No.5, pp.3687-3689.
• [2] Frees G.M. (1995): Disk drive spindle dynamics - analysis and measurement. - Advances in Information Storage Systems, vol.6, pp.237-262.
• [3] Ku C P.R. (1995): Dynamic characteristics of spindle motors supported by hydrodynamic bearings. - Proceeding of the 24th Incremental Motion Control System and Devices Conference, San Jose, CA, pp.223-232.
• [4] Ku C.P.R. (1996): Dynamic characteristics of hard disk drive spindle motors - comparison between ball bearings and hydrodynamic bearings. - Transactions of the ASME, Journal of Tribology, vol.118, pp A02-406.
• [5] Muijderman E.A., Remmers G. and Tielemans L.P.M.(1980): Grease-lubricated spiral groove bearings. - Philips Tech. Rev., vol.39, No.6/7, pp.793-803.
• [6] Ohmi T. (1996): Non-repeatable runout of ball-bearing spindle-motor for 2.5" HDD. - IEEE Transactions on Magnetics, vol.32, No.3, pp.1715-1720.
• [7] Ono K. and Takahasi K.( 1996): Theoretical analysis of shaft vibration supported by a ball bearing with small sinusoidal waviness. - IEEE Transactions on Magnetics, vol.32, No.3, pp.1709-1714.
• [8] Schirle N. and Lieu D.K. (1996): History and trends in the development of motorized spindles for hard disk drives. - IEEE Transactions on Magnetics, vol.32, No.3, pp.1703-1708.
• [9] Swann A.C., Harrisonn J.C., and Talke F.E. (1996): Non-repeatable runout measurement and simulation of fluid lubricated spindles. - IEEE Trans. On Magnetics, vol.132, No.3, pp.1727-1732.
• [10] Yoshida S (1996): Non-symmetrical three-lobe bearing spindle technology: A drive technology to increase Aerial Density. - I EEE Transactions on Magnetics, vol.32, No.3, pp.1721-1726.