Tytuł artykułu
Autorzy
Identyfikatory
Warianty tytułu
The evaluation of the coordinate measurement machines accuracy
Konferencja
Międzynarodowa Konferencja MANUFACTURING'04 : Współczesne problemy projektowania i wytwarzania [II; 2004; Poznań]
Języki publikacji
Abstrakty
W artykule przedstawiono wyniki testu dokładności trzynastu oprogramowań czołowych światowych firm. Testowano oprogramowania pod względem obliczeń poszczególnych elementów geometrycznych z założonym poziomem błędów. Dane wejściowe wprowadzono za pomocą klawiatury do komputera współpracującego ze współrzędnościową maszyną pomiarową (WMP). W Ten sposób uzyskano końcowy wynik obarczony jedynie błędami samego oprogramowania i komputera, wyłączając błędy WMP. Komputer i jego oprogramowanie traktowano jako „czarną skrzynkę". Do wszystkich badanych oprogramowań wprowadzono ten sam zestaw testowy.
In the article, the results of the Coordinate Measuring Machine accuracy test of the software delivered by 13 leading producers of CMM. The software had been tested for particular geometrical figures with given level of error. The initial data were introduced with keyboard of the computer cooperating with the CMM. This way only errors of the software and the computer caused the changes in the calculation results, excluding the errors of the CMM itself. Computer and its software was considered as a "back box", the test data were the same for each software.
Rocznik
Tom
Strony
353--359
Opis fizyczny
Bibliogr. 12 poz.
Twórcy
autor
- Instytut Technologii Mechanicznej Politechniki Poznańskiej
Bibliografia
- [1] Barker R.M., Harris P.M., Parkin G.I.: Software Support for Metrology Best Practice Guide No. 7: Development and Testing of Spreadsheet Applications. National Physical Laboratory (UK), 2000.
- [2] Brinkley D.: Guide to the Development of Software for Metrology SSfM Software Support for Metrology Best Practice Guide No. 3: Guidance on Developing Software for Metrology. Logica (UK).
- [3] Cox M.G.: A Discussion of Approaches for Determining a Reference Value in the Analysis of Key-Comparison Data. National Physical Laboratory (UK), Report CISE 42/99.
- [4] Cox M.G., Harris P.M.: Design and use of Reference Data Sets for Testing Scientific Software. Analytica Chimica Acta 380, 1999, s. 339-351.
- [5] Cox M.G., Harris P.M.: Guidelines to Help Users Select and use Software for their Metrology Applications. National Physical Laboratory (UK), Report CMSC 04/00, 2000.
- [6] Cox M.G., Forbes A.B., Harris P.M.: Software Support for Metrology Best Practice Guide, Discrete Modelling, 2002, No. 4.
- [7] Emmet L., Froome P.: Software Support for Metrology Best Practice Guide No. 2: The Development of Virtual Instruments. Adelard and Crown copyright 1999.
- [8] Lin Y.-J., Damodharan K., Shakarji C.: Standardised Reference Data Sets Generation for Coordinate Measuring Machine (CMM) Software Assessment. The International Journal of Advanced Manufacturing Technology, Springer-Verlag London Limited, 2001, s. 819-830.
- [9] Swornowski P.: The Optimum Number and Distribution of Measuring Points for the Circle with the Shape Deviation. Committee of Mechanical Engineering, Polish Academy of Sciences, Poznan Division, Archives of Mechanical Technology and Automatization, 2002, vol. 22, nr 2, s. 79-86.
- [10] Waldele F., Bittner B., Dreschner R., Elligsen R.: Test von Software fur Koordinatenmessgerate. VDI-Z, 1991, nr 12, s. 57-59.
- [11] Wichmann B.: Measurement Good Practice Guide No 5: Software in Scientific Instruments. National Physical Laboratory (UK), Crown copyright 1997.
- [12] DIN 32880 (1986):Koordinatenmesstechnik. Geometrische Grundlagen und Begriffe.
Typ dokumentu
Bibliografia
Identyfikator YADDA
bwmeta1.element.baztech-article-BPP1-0043-0075