The influence of the regulation method of cooling pump performance at heat transfer intensity in the pressure cooling

• Autorzy: Krakowski R.
• Języki publikacji: EN

Abstrakty

EN

This paper presents a model test stand for testing the cooling system with increased coolant temperature. On the model stand, as a result of the research, determined the characteristics of temperature and pressure courses coolant. The study was preceded by the determination of the intensity of the liquid flowing out of the engine block and flowing through the radiator as a function of the opening of the valve throttling the flow of liquid and as a function of speed water pump. An adjustable valve was located in the water outlet duct of the engine. During the test the cooling system was filled with coolant at 90%. After preliminary studies, the degree of filling of the liquid was found to be optimal, because the greater the amount of water in the system observed difficulties in obtaining elevated temperature, whereas at lower amounts of liquid vortex centrifugal pump had problems with the rib. Then, the characteristics of the two ways of controlling the pump capacity were made, ie by throttling the discharge and change in speed. The characteristics indicate that the first way to adjustment of the pump flow rate and thus cooling intensity was less effective, because a small amount of throttling was not affect the change. The second way to adjustment of the liquid flow rate with changes in the speed of the water pump was more efficient, because it was easier to maintain the pressure established in the cooling system.

Słowa kluczowe

EN

internal combustion engines; cooling system; model research; pump capacity

• Wydawca: Faculty of Ocean Engineering and Ship Technology, Gdańsk University of Technology
• Czasopismo: Journal of Polish CIMAC
• Rocznik: 2012
• Tom: Vol. 7, no 1
• Strony: 125--132
• Opis fizyczny: Bibliogr. 11 poz., rys.

Twórcy

autor

Krakowski R.

• Faculty of Marine Engineering ul. Morska 83 , 81-225 Gdynia, Poland tel.: [phone],

Bibliografia

• [1] Kawamura H., Development of the ceramic adiabatic engine having 68% thermal efficiency, ASME 2000 FALL TECHNICAL CONFERENCE, Peoria 2000.
• [2] Kneba Z., Kompleksowy model nowej generacji uk􀃡adu chłodzenia silnika spalinowego, Silniki Spalinowe, SC1/2007, R. 46.
• [3] Komo R., Bryzik W., Adiabatic turbocompound diesel engine, Paper D4.5 CIMAC CONGRES, Paryż1983.
• [4] Krakowski R., Wpływ podwyższonej temperatury płynu chłodzącego na zwiększenie ekonomiczności pracy tłokowego silnika spalinowego, Zeszyty Naukowe Akademii Morskiej w Gdyni, 2011, nr 68.
• [5] Luft S., Podstawy budowy silników, WKŁ Warszawa 2006.
• [6] Walentynowicz J., Stanowisko testowe do badania układów chłodzenia silników spalinowych, Journal of KONES, Vol. 14, 2007, No 4.
• [7] Walentynowicz J., Wyznaczanie bilansu cieplnego silnika spalinowego o zapłonie samoczynnym, Biuletyn WAT, 2006, nr 2.
• [8] Walentynowicz J., Krakowski R., Decreasing of thermal energy loses in piston combustion engines, RSM “System Level Thermal Management for Enhanced Platform Mobility” NATO RTO AVT – 178, Bucharest 4-7.10.2010.
• [9] Przybylski, W.,Współczesne problemy w technologii obróbki przez nagniatanie, Wydawnictwa Politechniki Gdańskiej, Gdańsk 2005.
• [10] Sneller, Slavko, The “Cold Corrosion” Limits of Marine Exhaust-Gas Boiler, IX Symposium on Theory and Practica of Shipbuilding. In memorien prof. Leopold Sorta, pp. 192-200, Dubrownik 1990.
• [10] Mroziński S., Skocki R., Wrażliwość parametrów pętli histerezy na zmiany właciwości cyklicznych. XXIV Sympozjum Zmęczenia i Mechaniki Pękania, Bydgoszcz –Pieczyska 2012, pp. 105-106.