PL EN


Preferencje help
Widoczny [Schowaj] Abstrakt
Liczba wyników
Tytuł artykułu

Microscale interpretation of tribological phenomena in Ti/TiN soft-hard multilayer coatings on soft austenite steel substrates

Autorzy
Treść / Zawartość
Identyfikatory
Warianty tytułu
Języki publikacji
EN
Abstrakty
EN
The mechanical and tribological behavior of physical vapor deposited coatings on soft substrate materials gains increasing interest due to economical and environmental aspects – e.g. substitution of steels by light-weight metals or polymers in transport vehicles. Nevertheless, such soft materials require surface protection against wear in tribological contacts. Single layer hard coatings deposited at room temperature are brittle with a relatively poor adhesion. Therefore, they should be better substituted by tough multilayer coatings of soft-hard material combinations. However, the mechanics of such multilayer coatings with several 10 nm thick bilayer periods is difficult and yet not well described. The presented work tries to fill the gap of knowledge by focusing both on mechanical investigations of hardness, adhesion, and wear and on microscopic elucidation of deformation mechanisms. In the paper 1 ěm thick Ti/TiN multilayer stacks were deposited by magnetron sputtering on soft austenitic steel substrates at room temperature to prevent distortion of functional components in future applications. High hardness was found for 8 and 16 bilayer films with modulation ratio Ti:TiN = 1:2 and 1:4. This was attributed (with use of transmission electron microscopy) to stopping the crack propagation in thin Ti layers of the multilayer systems by shear deformation combined with different fracture mechanisms in comparison with that for the TiN single layers (edge cracks at the border of the contact area and ring cracks outside, respectively).
Słowa kluczowe
Rocznik
Strony
343--355
Opis fizyczny
Bibliogr. 82 poz., rys., tab.
Twórcy
autor
autor
autor
  • Institute for Surface Technologies and Photonics, Joanneum Research Forschungsges.m.b.H., Functional Surfaces, Leobner Straße 94, A-8712 Niklasdorf, Austria, nmlmajor@imim-pan.krakow.pl
Bibliografia
  • [1] H. Holleck and V. Schier, “Multilayer PVD coatings for wear protection”, Surf. Coat. Technol. 76–77, 328–336 (1995).
  • [2] M. Nordin, M. Larsson, and S. Hogmark, “Mechanical and tribological properties of multilayered PVD TiN/CrN, TiN/MoN, TiN/NbN and TiN/TaN coatings on cemented carbide”, Surf. Coat. Technol. 106, 234–241 (1998).
  • [3] A.A. Voevodin, J.M. Schneider, C. Rebholz, and A. Matthews, “Multilayer composite ceramic- metal- DLC coatings for sliding wear applications”, Tribol. Int. 29, 559–570 (1996).
  • [4] M. Stueber, H. Holleck, H. Leiste, K. Seemann, S. Ulrich, and C. Ziebert, “Concepts for the design of advanced nanoscale PVD multilayer protective thin films”, J. Alloys and Compounds 483, 321- 333 (2009).
  • [5] E. Martinez, J. Romero, A. Lousa, and J. Esteve, “Nanoindentation stress-strain curves as a method for thin-film complete mechanical characterization: application to nanometric CrN/Cr multilayer coatings”, Appl. Phys. A 77, 419–426 (2003).
  • [6] J. Smolik and K. Zdunek, “Effect of interlayer composition on the tribological properties of TiC/Ti(Cx, N1− x)/TiN antiabrasive multi-layer coatings”, Vacuum 55, 147–151 (1999).
  • [7] Y.L. Su and W.H. Kao, “Optimum multilayer TiN-TiCN coatings for wear resistance and actual application”, Wear 223, 119–130 (1998).
  • [8] N. D¨uck, W. Gamer, M. Gesatzke, W. Griepentrog, M. ¨Osterle, I. Sahre, and ˇZ. Urban, “Ti/TiN multilayer coatings, deposition technique, characterization and mechanical properties”, Surf. Coat. Technol. 142–144, 579–584 (2001).
  • [9] S. Labdi, Ph. Houdy, P. Psyllaki, and M. Jeandin, “Elaboration and characterization of Ti and TiN thin films and Ti/TiN multilayers for hard coating applications”, Thin Solid Films 275, 213–215 (1996).
  • [10] M. Nordin, M. Larsson, and S. Hogmark, “Mechanical and tribological properties of multilayered PVD TiNrCrN”, Wear 232, 221–225 (1999).
  • [11] M. Nordin, M. Larsson, and S. Hogmark, “Wear resistance of multilayered PVD TiN/TaN on HSS”, Surf. Coat. Technol. 120–121, 528–534 (1999).
  • [12] J. Smolik, K. Zdunek, and B. Larisch, “Investigation of adhesion between component layers of a multi-layer coating TiC/Ti(Cx, N1− x)/TiN by the scratch-test method”, Vacuum 55, 45–50 (1999).
  • [13] M. Bromark, M. Larsson, P. Hedenqvist, and S. Hogmark, “Wear of PVD Ti/TiN multilayer coatings”, Surf. Coat. Technol. 90, 217–223 (1997).
  • [14] A. Leyland and A. Matthews, “Thick Ti/TiN multilayered coatings for abrasive and erosive wear resistance”, Surf. Coat. Technol. 70, 19–25 (1994).
  • [15] A. Matthews and S.S. Eskilden, “Engineering applications for diamond-like carbon”, Diamond Relat. Mater. 3, 902–911 (1994).
  • [16] K. Holmberg, A. Matthews, and H. Ronkainen, “Coatings tribology–contact mechanics and surface design”, Tribol. Int. 31 (1–3), 107–120 (1998).
  • [17] A. Matthews, R. Jones, and S. Dowey, “Modelling the deformation behaviour of multilayer coatings”, Tribology Letters 11, 103–106 (2001).
  • [18] G.S.Kim, S.Y.Lee, J.H.Hahn, B.Y.Lee, J.G.Han, J.H.Lee, and S.Y.Lee, “Effects of the thickness of Ti buffer layer on the mechanical properties of TiN coatings”, Surf. Coat. Technol. 171, 83–90 (2003).
  • [19] J.M. Lackner, “Industrially-scaled room-temperature pulsed laser deposition of Ti-TiN multilayer coatings”, J. Physics, Conf. Series 59, 16–21 (2007).
  • [20] Z. Farhat, Y. Ding, D.O. Northwood, and A.T. Alpas, “Nanoindentation and friction studies on Ti-based nanolaminated films”, Surf. Coat. Technol. 89, 24–30 (1997).
  • [21] S. Zhang and N. Ali, Nanocomposite Thin Films and Coatings, Imperial Colleage Press, London, 2007.
  • [22] A. Leyland and A. Matthews, “Thick Ti/TiN multilayered coatings for abrasive and erosive wear resistance”, Surf. Coat. Technol. 70, 19–25 (1994).
  • [23] K. Holmberg, A. Matthews, and H. Ronkainen, “Coatings tribology – contact mechanisms and surface design”, Tribol. Intern. 31, 107–120 (1998).
  • [24] K.S. Chan, M.Y. He, and J.W. Hutchinsson, “Cracking and stress redistribution in ceramic layered composites”, Mater. Sci. Eng. 167, 57–64 (1993).
  • [25] M.Y. He and A.G. Evens, “Crack deflection at an interface between dissimilar elastic materials, role of residual stresses”, Int. J. Solids. Struct. 31, 3443–3455 (1994).
  • [26] J.M. Lackner, Industrially-scaled hybrid Pulsed Laser Deposition at Room Temperature, Orekop, Kraków, 2006.
  • [27] W.C. Oliver and G.M. Pharr, “Piezoelectric nanoindentation”, J. Materials Research 7, 1564–1583 (1992).
  • [28] A.C. Fischer-Cripps, “Critical review of analysis and interpretation of nanoindentation test data”, Surface and Coatings Technology 200, 4153–4165 (2006).
  • [29] X.C. Zhang, B.S. Xu, H.D. Wang, and Y.X. Wu, “Hertzian contact response of single-layer, functionally graded and sandwich coatings”, Materials and Design 28, 47–54 (2007).
  • [30] M.T. Tilbrook, D.J. Paton, Z. Xie, and M. Hoffman, “Microstructural effects on indentation failure mechanisms in TiN coatings, finite element simulations”, Acta Materialia 55, 2489–2501 (2007).
  • [31] D.E. Vlachos, Y.P. Markopoulos, and V. Kostopoulos, “3-D modeling of nanoindentation experiment on a coating-substrate system”, Computational Mechanics 27, 138–144 (2001).
  • [32] S.B. Liu, A. Peyronnel, Q.J. Wang, and L.M. Keer, “An extension of the Hertz theory for 2D coated components”, Tribology Letters 18, 505–511 (2005).
  • [33] X.C. Zhang, B.S. Xu, H.D. Wang, Y.X. Wu, and Y. Jiang, “Hertzian contact response of single-layer, functionally graded and sandwich coatings”, Materials and Design 28, 47–54 (2007).
  • [34] I. Pane and E. Blank, “Response to loading and stiffness of coated substrates indented by spheres”, Surface and Coatings Technology 200, 1761–1767 (2005).
  • [35] M. Kot, “Deformations and fracture of coating-substrate systems under contact load”, Tribologia 231, 125–134 (2010).
  • [36] B.R. Lawn, “Fracture and deformation in brittle solids, a perspective on the issue of scale”, J. Mater. Res. 19, 22–29 (2004).
  • [37] B.R. Lawn and T.R. Wilshaw, “lndentation fracture: principles and applications”, J. Mater. Sci. 10, 1049–1081 (1975).
  • [38] B.R. Lawn, Y. Deng, P. Miranda, A. Pajares, H. Chai, and D.K. Kim, “Overview: damage in brittle layer structures from concentrated loads”, J. Mater. Res. 17, 3019–3036 (2002).
  • [39] H. Chai, B.R. Lawn, and S.Wuttiphan, “Fracture modes in brittle coatings with large interlayer modulus mismatch”, J. Mater. Res. 14, 3805–3817 (1999).
  • [40] E. Weppelmann and M.V. Swain, “Investigation of the stresses and stress intensity factors responsible for fracture of thin protective films during ultra-micro indentation tests with spherical indenters”, Thin Solid Films 286, 111–121 (1996).
  • [41] R. Anderson, G. Toth, L. Gan, and M.V. Swain, “Indentation response and cracking of sub-micron silica films on a polymeric substrate”, Eng. Fract. Mech. 61, 93–105 (1998).
  • [42] H. Chai and B.R. Lawn, “Role of adhesive interlayer I transverse fracture of brittle layer structures”, J. Mater. Res. 15, 1653–1660 (2000).
  • [43] A. Leyland and A. Matthews, “On the significance of the H/E ratio in wear control: a nanocomposite coating approach to optimised tribological behavior”, Wear 246, 1–11 (2000).
  • [44] A. Matthews and A. Leyland, “Developments in PVD tribological coatings”, Proc. 5th ASM Heat Treatment and Surface Engineering Conf. Eur. 1, CD-ROM (2000).
  • [45] K. Holmberg and A. Matthews, Coatings Tribology, Properties, Techniques and Applications, Surface Engineering, Elsevier, Amsterdam, 1996.
  • [46] K. Holmberg and A. Matthews, “Coatings tribology: a concept, critical aspects and future directions”, Thin Solid Films 253, 173–178 (1994).
  • [47] A. Matthews, A. Leyland, K. Holmberg, and H. Ronkainen, “Design aspects for advanced tribological surface coatings”, Surf. Coat. Technol. 100–101, 1–6 (1998).
  • [48] J. Michler and E. Blank, “Analysis of coating fracture and substrate plasticity induced by spherical indentors: diamond and diamond-like carbon layers on steel substrates”, Thin Solid Films 381, 119–134 (2001).
  • [49] R.F. Bunshah, Handbook of Hard Coating, William Andrew Publishing, Norwich, 2001.
  • [50] S. Gwidon and W. Stachowiak, Wear – Materials, Mechanisms and Practise, Wiley, Chichester, 2005.
  • [51] J.M. Lackner, W. Waldhauser, A. Alamanou, C. Teichert, F. Schmied, L. Major, and B. Major, “Mechanisms for selfassembling topography formation in low-temperature vacuum deposition of inorganic coatings on polymer surfaces”, Bull. Pol. Ac.: Tech. 58, 281–294 (2010).
  • [52] A. Lousa, J. Romero, E. Martinez, J. Esteve, F. Montala, and L. Carrera, “Multilayered chromium/chromium nitride coatings for use in pressure die-casting”, Surface and Coatings Technology 146–147, 268–273 (2001).
  • [53] J. Romero, J. Esteve, and A. Lousa, “Period dependence of hardness and microstructure on nanometric Cr/CrN multilayers”, Surface and Coatings Technology 188–189, 338–343 (2004).
  • [54] L. Maille, P. Aubert, C. Sant, and P. Garnier, “A mechanical study of W-N/W multilayers”, Surface and Coatings Technology 180–181, 483–487 (2004).
  • [55] S.K. Kim, Y.J. Baik, and D. Kwon, “Analysis of interfacial strengthening from composite hardness of TiN/VN and TiN/NbN multilayer hard coatings Technology 187, 47–53 (2004).
  • [56] G. Abadias, S. Dub, and R. Shmeger, “Nanoindentation hardness and structure of ion beam sputtered TiN, W and TiN/W multilayer hard coatings”, Surface and Coatings Technology 200, 6538–6543 (2006).
  • [57] M. Berger, U. Wiklund, M. Eriksson, H. Engqvist, and S. Jacobson, “The multilayer effect in abrasion – optimising the combination of hard and tough phases”, Surface and Coatings Technology 116–119, 1138–1144 (1999).
  • [58] M. Kot, W.A. Rakowski, Ł. Major , R. Major, and J. Morgiel, “Effect of bilayer period on properties of Cr/CrN multilayer coatings produced by laser ablation”, Surface and Coatings Technology 202, 3501–3506 (2008).
  • [59] S.K. Tien and J.G. Duh, “Effect of heat treatment on mechanical properties and microstructure of CrN/AlN multilayer coatings”, Thin Solid Films 494, 173–178 (2006).
  • [60] G.S. Kim, S.Y. Lee, and J.H. Hahn, “Synthesis of CrN/AlN superlattice coatings using closed-field unbalanced magnetron sputtering process”, Surf. Coat. Technol. 171, 91–95 (2003).
  • [61] A. D¨uck, N. Gamer, W. Gesatzke, M. Griepentrog, W. ¨Osterle, M. Sahre, and I. Urban, “Ti/TiN multilayer coatings: deposition technique, characterization and mechanical properties”, Surf. Coat. Technol. 142–144, 579–584 (2001).
  • [62] E.O. Hall, “The deformation and ageing of mild steel”, lst Proc. Physics Society III Discussion of Results B 64, 747–753 (1951).
  • [63] S.L. Lehoczky, “Retardation of dislocation generation and motion in thin-layered metal laminates”, Review Letter 41, 1814–1819 (1978).
  • [64] M.T. Vieira and A.S. Ramos, “The influence of ductile interlayers on the mechanical performance of tungsten nitride coatings”, J. Materials Processing Technology 92–93, 156–161 (1999).
  • [65] E. Bemporad, M. Sebastiani, C. Pecchio, and S. De Rossi, “High thickness Ti/TiN multilayer thin coatings for wear resistant applications”, Surface and Coatings Technology 201, 2155–2165 (2006).
  • [66] A. Leyland and A. Matthews, “Design criteria for wearresistant nanostructured and glassy-metal coatings”, Surf. Coat. Technol. 177–178, 317–324 (2004).
  • [67] T.Y. Tsui, G.M. Pharr, W.C. Oliver, C.S. Bhatia, R.L. White, S. Anders, A. Anders, and I.G. Brown, “Nanoindentation and nanoscratching of hard carbon coatings for magnetic disks mater”, Res. Soc. Symp. Proc. 383, 447–452 (1995).
  • [68] J. Musil, “Hard and superhard nanocomposite coatings”, Surface and Coatings Technology 125, 322–330 (2000).
  • [69] Y.T. Pei, P. Huizenga, D. Galvan, and J.Th.M. De Hossona, “Self-lubrication and wear behavior of TiC/a-C:H nanocomposite coatings”, J.. Appl. Phys. 100, 114309–114318 (2006).
  • [70] A. Karimi, Y. Wang, T. Cselle, and M. Morstein, “Fracture mechanisms in nanoscale layered hard thin films”, Thin Solid Films 420–421, 275–280 (2002).
  • [71] J.W. Hutchinson, M.D. Thouless, and E.G. Liniger, “Growth and configurational stability of circular, buckling-driven film delaminations”, Acta Metall. 40, 295–308 (1992).
  • [72] M. Kot, L. Major, J.M. Lackner, and W. Rakowski, “Analysis of the influence of sublayer thickness on the deformation mechanism and fracture of {Ti/TiN} multilayer”, Tribology 232, 181–189 (2010).
  • [73] M. Kot, W. Rakowski, J. Morgiel, and L. Major, “Deformation of coating-substrate systems under contact load”, Tribology 218, 285–295 (2008).
  • [74] E.G. Herbert, G.M. Pharr, W.C. Oliver, B.N. Lucas, and J.L. Hay,” On the measurement of stress–strain curves by spherical indentation”, Thin Solid Films 398–399, 331–335 (2001).
  • [75] N.J.M. Carvalho and J.Th.M. De Hosson, “Deformation mechanisms in TiN/(Ti,Al)N multilayers under depth-sensing indentation”, Acta Materialia 54, 1857–1862 (2006).
  • [76] M. Oden, H. Ljungcrantz, and L. Hultman, “Characterization of the induced plastic zone in a single crystal TiN(001) film by nanoindentation and transmission electron microscopy”, J. Mater. Res. 12, 2134–2142 (1997).
  • [77] T. Hayashi and S.Mukamel, “Multidimensional infrared signatures of intramolecular hydrogen-bonding in malonaldehyde”, J.Phys.Chem. 1079, 113–9131 (2003).
  • [78] J.-K. Park, C. Ziebert, M. St ¨uber, and Y.-J. Baik, “Improvement of hardness and toughness of TiAlN coating by nanoscale multilayered structurization with Si3N4, Plasma Process. Polym. 4, 902–905 (2007).
  • [79] Z.H. Xie, M. Hoffman, P. Munroe, A. Bendavid, and P.J. Martin, “Deformation mechanisms of TiN multilayer coatings alternated by ductile or stiff interlayers”, Acta Materialia 56, 852–861 (2008).
  • [80] K.J. Ma, A. Bloyce, and T. Bell, “Examination of mechanical properties and failure mechanisms of TiN and Ti-TiN multilayer coatings”, Surf. Coat. Technol. 76–77, 297–302(1995).
  • [81] R. H¨ubler, G.K. Wolf, W.H. Schreiner, and I.J.R. Baumvol,” Ion beam mixing of Al–AlN multilayers for tribological and corrosion protection”, Nuc. Inst. Met. Phy. Res. B 80–81, 1415–1418 (1993).
  • [82] E. Martinez, J. Romero, A. Lousa, and J. Esteve, “Wear behavior of nanometric CrN/Cr multilayers”, Surface and Coatings Technology 163–164, 571–577 (2003).
Typ dokumentu
Bibliografia
Identyfikator YADDA
bwmeta1.element.baztech-article-BPG8-0070-0022
JavaScript jest wyłączony w Twojej przeglądarce internetowej. Włącz go, a następnie odśwież stronę, aby móc w pełni z niej korzystać.