Forging and rolling of magnesium alloy AZ61

• Autorzy: Greger M. , Kocich R. , Čižek L.
• Konferencja: 12th International Scientific Conference CAM3S'2006, 27-30th November 2006, Gliwice-Zakopane
• Języki publikacji: EN

Abstrakty

EN

Purpose: The paper summarises results of experiments aimed at development of structure of modified alloy AZ61 at hot deformation. Design/methodology/approach: Deformation behaviour of alloy was verified at the temperature of 420 degrees centigrade by rolling at 380 degrees centigrade by forging, respectively. Findings: Magnesium alloy AZ 61 have hexagonal structure and their forming is at room temperatures very difficult, that's why big plastic deformations are carried out in hot condition. After plastic deformations was obtained that original grain size decreased 15 times. Research limitations/implications: This paper provide data about magnitude of deformation, strain rate and temperature of forming at different techniques of plastic deformation. It was aimed to determine the conditions for non problem rolling and forging respectively. Practical implications: Initial structure was as cast and after heat treatment T4. Heat treatment appeared much better for forming as well as forging than rolling because of state of stress. Originality/value: Role of beta phase (Mg17Al12) in these alloys at plastic forming is very important, such that how it was obtained, best final properties of AZ 61 alloy supports very fine particles, distributed into Mg matrix. Next a relevant information is that multi stage forming process is much better in comparison with a big single reduction.

Słowa kluczowe

EN

plastic forming rolling; forging; magnesium alloy

PL

formowanie plastyczne; walcowanie; kucie; stop magnezu

• Wydawca: International OCSCO World Press
• Czasopismo: Journal of Achievements in Materials and Manufacturing Engineering
• Rocznik: 2007
• Tom: Vol. 20, nr 1-2
• Strony: 447--450
• Opis fizyczny: Bibliogr. 15 poz., fot., rys.

Twórcy

autor

Greger M.

autor

Kocich R.

autor

Čižek L.

• VSB - Technical University Ostrava, 17. listopadu 15, 708 33 Ostrava-Poruba, Czech Republic,

Bibliografia

• [1] O. Muransky, P. Hornak, P. Lukas, J. Zrnik, P. Sittner, 11th International AMME'2005, Gliwice, 694-697.
• [2] K. Kuzman, M. Nastran, Some comments on stability analysis of the cold forming process, AMME'1998 Zakopane, 345-348.
• [3] S.M. Pytel, Tomaszewska-Gorecka, Resistivity on creep of ultralowcarbon bainit steel, 7th International AMME'2000, 443-448.
• [4] J. Zhuo, P. Ding, Investigation on the rolling performances and qualified rate of commercial purity aluminium foils, 9th International AMME'2000, 585-588.
• [5] S. Tkaczyk, M. Kciuk, Corosion ressistance under the stress influence of AlMg5 alloy, 9th International AMME'2000, 535-538.
• [6] M. Greger, L. Čižek, Z. Muskalski, Magnesium and its alloys for forming, International conference Forming, 2004, 75-78.
• [7] A.V. Sergueeva, V.V. Stolyarov, R.Z. Valiev, A.K. Mukherjee, Enhanced superplasticity in a Ti-6A1-4V alloy processed by severe plastic deformation, Scr. Mater., 43 (2000) 819.
• [8] L. Čižek, M. Greger, S. Rusz, I. Juřička, L.A. Dobrzanski, T. Tanski, Structure characteristics after rolling of magnesium alloys, AMME'2002, Gliwice, 87-90.
• [9] P. Guyot, G.M. Raynaud, Dislocation Structure Distributions and Properties of Heavily Cold Rolled Aluminium and Aluminium-Magnesium Alloys, Acta metall.mater., 39 (1991) 317-322.
• [10] H. Watanabe, T. Mukai, K. Higashi, Grain refinement and superplasticity in magnesium alloys Ultrafine Grained Materials II. Proceedings. TMS Annual Meeting, (2003) 469-78.
• [11] M. Greger, R. Kocich and L. Čižek. Evaluation of formability of the alloy AZ91 with use of wedge test, International conference Metal, (2005).
• [12] M.M. Avedesian, H. Baker (Eds.), ASM Specialty Handbook Magnesium and Magnesium Alloys, The Materials Information Society, Materials Park, OH, 1999, 78-84.
• [13] M. Greger, L. Čižek, R. Kocich, A. Silbernagel, Possibilities of magnesium extrusion with use of the ECAP method, Acta Metallurgica Slovaca, 10 (2004) 499-503.
• [14] D. Tomus, K. Tsuchiya, T. Nagano, A. Hosokawa, T. Ohmori, M. Sasaki, Y. Todaka, M. Umemoto, Mater.Trans.,45 (2004) 219.
• [15] Kevorkijan, AZ80 and ZC71/SiC/12p closed die forgings for automotive applications: technical and economic assessment of possible mass production, Materials Science and Technology., 19(2003) 1386-1390.