The effect of the assembling stresses on the parameters of a low power induction motor

• Autorzy: Pulnikov A. , Permiakov V. , Dupre L. , Gyselinck J. , Petrov R. , Wisselink H. , Dular P. , Melkebeek J.

Warianty tytułu

PL

Wpływ naprężeń montażowych na parametry silnika indukcyjnego małej mocy

• Konferencja: 8th International Workshop on 1&2-Dimensional Magnetic Measurement and Testing, Ghent, Belgium, 27-28 September 2004
• Języki publikacji: EN

Abstrakty

EN

In this paper the effect of assembling stresses on the no-load parameters of a low power induction motor is investigated. The modification of the main inductance of the equivalent circuit is studied.

PL

Przedstawiono badania wpływu naprężeń na parametry nieobciążonej maszyny indukcyjnej małej mocy. Analizowano zmiany indukcyjności schematu zastępczego maszyny.

Słowa kluczowe

EN

induction motor; assembling; stress

PL

silnik indukcyjny; naprężenie

• Wydawca: Wydawnictwo SIGMA-NOT
• Czasopismo: Przegląd Elektrotechniczny
• Rocznik: 2005
• Tom: R. 81, nr 5
• Strony: 73--78
• Opis fizyczny: Bibliogr. 6 poz., rys.

Twórcy

autor

Pulnikov A.

• Electrical Energy Laboratory, Department of Electrical Energy, Systems and Automation, Ghent University

autor

Permiakov V.

• Electrical Energy Laboratory, Department of Electrical Energy, Systems and Automation, Ghent University

autor

Dupre L.

• Electrical Energy Laboratory, Department of Electrical Energy, Systems and Automation, Ghent University

autor

Gyselinck J.

• Free University of Brussels (ULB), Department of Electrical Engineering, Avenue Franklin Roosevelt 50, B-1050 Brussels, Belgium

autor

Petrov R.

• Laboratory for Iron and Steelmaking, Technologiepark Zwijnaarde 903, B-9052 Gent, Belgium

autor

Wisselink H.

• Netherlands Institute for Metals Research, Department of Mechanical Engineering, University of Twente

autor

Dular P.

• Montefiore Institute, University of Liège, Parking P32 - Building B28, Sart Tilman campus, Liege B-4000, Belgium

autor

Melkebeek J.

• Electrical Energy Laboratory, Department of Electrical Energy, Systems and Automation, Ghent University

Bibliografia

• [1] Pulnikov A., Permiakov V., De Wulf M., Melkebeek J., Measuring setup for the investigation of the influence of mechanical stresses on magnetic properties of electrical steel, J Magn. Magn. Mat., 254-255 (2003) 47-49.
• [2] Pulnikov A., Modification of Magnetic Properties of Non Oriented Electrical Steels by the Production of Electromagnetic Devices, PhD thesis, Ghent University (2004).
• [3] Dabrowski M., Zgodzinski T., Some Effects of Unidirectional Stress in Si-Fe Sheets, Physica Scripta, 40 (1989), 514-517.
• [4] Foot G.E., Overshot t K.J., The effect of tensile stress on the domain wall motion and wall bowing in 3% grain-oriented silicon-iron, IEEE Trans. Magn., 17 (1981), n.6, 2869-2871.
• [5] M.J. Sablik, L.A. Riley, G.L. Burkhardt, H. Kwun, P.Y. Cannell, K.T.Watts, R.A.Langman, “Micromagnetic model for the influence of biaxial stress on hysteretic magnetic properties”, J. Appl. Phys. Vol. 75(10), May 1994, pp. 5673-5675.
• [6] Gyselinck J., Twee-Dimensionale Dynamische Eindige- Elementenmodellering van Statische en Roterende Elektromagnetische Energieomzetters, PhD thesis, Ghent University (2000).