PL EN


Preferencje help
Widoczny [Schowaj] Abstrakt
Liczba wyników
Tytuł artykułu

Wpływ koncentracji chromu na strukturę i własności mechaniczne płaskowników ze stopu EN AW-6061

Autorzy
Identyfikatory
Warianty tytułu
EN
The influence of chromium addition on the structure and mechanical properties of flat bars from the EN AW-6061 alloy
Języki publikacji
PL
Abstrakty
PL
W artykule przedstawiono wpływ dodatku Cr (0,05 % i 0,35 %) oraz warunków chłodzenia po wyciskaniu na strukturę i własności mechaniczne płaskowników ze stopu Al-Mg2Si1,24 %-Si0,20 % (typu EN AW-6061). Stwierdzono, że: 1 — wystąpienie presefektu jest zdeterminowane przez wysoką koncentrację Cr i intensywne chłodzenie po wyciskaniu (nadmuchem powietrza), podczas gdy gruboziarnista, zrekrystalizowana struktura jest typową zarówno dla materiału studzonego samoistnie (na powietrzu) jak i ubogiego w dodatek Cr; 2 — oba typy struktur są stabilne podczas późniejszego zabiegu przesycania; 3 — siedmiokrotny wzrost koncentracji Cr powoduje ~30-krotne zmniejszenie wielkości ziarna, czego konsekwencją jest znaczny wzrost parametrów wytrzymałościowych stopu: R0,2, Rm i HB w stanie przesyconym i T4 (o ponad, odpowiednio, 20 %, 10 % i 5 %). Dla stanu T6 wpływ wielkości ziarna na R0,2 i Rm nie przekracza 5 %, a dla HB jest znikomy.
EN
The influence of Cr addition (0.05 % and 0.35 %) and the mode of cooling after extrusion on the structure and mechanical properties of the flat bars from the alloy Al-Mg2Si1.24 %-Si0.20 % (EN AW-6061 type) was investigated. It has been shown that: 1 — the occurrence of the pressefect is determined by high Cr concentration and intensive cooling after extrusion (in air stream), while the coarse-grained, recrystallized structure is typical both for that self-cooled (on air) as well as for that lean in Cr; 2 — the structure are stable during subsequent solution treatment; 3 — the 7-fold increase in Cr addition causes ~30-fold decrease in grain size and it leads to increase in strengthening parameters of material: R0.2, Rm and HB in solid solution state and T4 state (over 20 %, 10 % and 5 %, respectively). For T6 state, the effect of grain size not exceeds 5 % (for R0.2 and Rm) and is neglected for the HB number.
Rocznik
Strony
31--34
Opis fizyczny
Bibliogr. 9 poz., rys., wykr.
Twórcy
autor
autor
  • Akademia Górniczo-Hutnicza, Wydział Metali Nieżelaznych, Kraków
Bibliografia
  • 1. Mc Queen H. J., Celliers O. C.: Application of hot workability studies to extrusion processing: Part II. Microstructural development and extrusion of Al, Al-Mg and Al-Mg-Mn alloys. Canad. Met. Quart., 1996, t. 35, nr 4, s. 305÷319. Rys.2. Krzywe starzenia naturalnego i sztucznego płaskowników ze stopu EN AW-6061
  • 2. Hulley S. I., Lorimer G. W.: The effect of dispersoids on the recrystallisation behaviour of a series of aluminium-magnesium-silicon alloys. Proc. 3th Int. Conf. Aluminium Alloys. Trondheim (Norwegia) 1992, s. 361÷366.
  • 3. Ranganathan K., Last H. R., Sanders T. H.: Precipitation of metastable Al3Zr (β’) in aluminium alloys. Proc. 3th Int. Conf. Aluminium Alloys. Trondheim (Norwegia) 1992, t. 2, s. 15÷20. Fig.2. Natural and artificial ageing curves for flat bars from EN AW-6061 alloys
  • 4. Chadwick R., Muir N. B., Grainger H. B.: The effect of iron, manganese and chromium on the properties in sheet form of aluminium alloys containing 0.7 % magnesium and 1.0 % silicon. J. Inst. Met. 1953÷1954, t. 82, nr 2, s. 75÷80.
  • 5. Matsuda K., Taniguchi S., Kido K., Ikeno S.: Effect of addition of copper and chromium on the precipitation in Al-Mg-Si alloys. Mat. Sci. Forum 2002, t. 396÷402, s. 941÷946.
  • 6. Lodgaard L., Ryum N.: Precipitation of dispersoids containing Mn and/or Cr in Al-Mg-Si alloys. Mat. Sci. Eng. A283, 2000, s. 144÷152.
  • 7. Embury J. D.: Strengthening mechanisms in an Al alloys — an overview of natural limits and engineering possibilities. Mat. Sci. Forum 1996, t. 217÷222, s. 57÷70.
  • 8. Carter R. D., Lee E. W., Starke Jr. E. A., Beevers C. J.: The effect of microstructure and environment on fatigue crack closure of 7475 aluminum alloy. Met. Trans. 15A, 1984, t. 3, s. 555÷563.
  • 9. Totten G. E., Mac Kenzie D. S.: Handbook of aluminum. Marcel Decker Inc., New York–Basel, 2003, t. 1, s. 101. 34
Typ dokumentu
Bibliografia
Identyfikator YADDA
bwmeta1.element.baztech-article-AGH2-0004-0067
JavaScript jest wyłączony w Twojej przeglądarce internetowej. Włącz go, a następnie odśwież stronę, aby móc w pełni z niej korzystać.