Tytuł artykułu
Autorzy
Wybrane pełne teksty z tego czasopisma
Identyfikatory
Warianty tytułu
The alumina matrix composites for cutting tool points
Języki publikacji
Abstrakty
W artykule opisano sposób wytwarzania i podstawowe właściwości mechaniczne kompozytów Al2O3 – x % wag. TiB2 (x = 1, 2,5, 5, 7,5, 10 i 15). Finalne zagęszczenie kompozytów przebiegało jedną z dwóch metod: spiekanie swobodne lub prasowanie na gorąco. Seria kompozytów spiekanych swobodnie charakteryzowała się niską gęstością względną. Z tego względu dalszym badaniom zostały poddane tylko kompozyty wytwarzane na drodze prasowania na gorąco. W przypadku kompozytów spiekanych pod ciśnieniem uzyskane gęstości względne nie były niższe niż 98,4 %. W pracy przedstawiono również wyniki porowatości i nasiąkliwości próbek. Kompozyty spiekane pod ciśnieniem posiadają wysoką twardością dochodzącą do 1968 HV20 w przypadku próbki Al2O3 – 10 % wag. TiB2. Wyniki modułu Younga są bardzo zbliżone do wartości teoretycznych wyliczonych z reguły mieszanin i zawierają się w przedziale od 399 GPa do 420 GPa.
The article describes a way of production and basic mechanical properties of the Al2O3 – x wt.%TiB2 (x = 1, 2.5, 5, 7.5, 10 and 15) composites. Final densification was carried out by using one of two methods: natural sintering or hot pressing. A series of atmospheric pressure sintered composites showed a low relative density. Thereby only the hot pressed composites were further examined. In case of the hot pressed composites the relative density results were not lower than 98.4 %. In current work, the results of porosity and absorbability measurements are also present. The hot pressed composites have high hardness reaching 1968 HV20 for the Al2O3 – 10 wt.% TiB2 sample. The measured values of Young’s modulus are very close to theoretical values calculated from the rule of mixture, and they range from 399 GPa to 420 GPa.
Słowa kluczowe
Wydawca
Czasopismo
Rocznik
Tom
Strony
434--438
Opis fizyczny
Bibliogr. 7 poz., rys., wykr., tab.
Twórcy
autor
autor
autor
- Wydział Inżynierii Materiałowej Politechniki Warszawskiej, ul. Wołoska 141, 02-507 Warszawa, k.broniszewski@inmat.pw.edu.pl
Bibliografia
- [1] Gibas T.: Korund i jego zastosowanie w technice, Wydawnictwo Śląsk, Katowice, (1970).
- [2] Like Q.: „Types, performance and application of Al2O3 system ceramic cutting tool”, Journal of Rare Earths, 25, (2007) 322-326.
- [3] Deng J., Cao T., Liu L.: „Self-lubricating behaviors of Al2O3/TiB2 ceramic tools in dry high-speed machining of hardened steel”, J. Eur. Ceram. Soc., 25, (2005), 1073–1079.
- [4] Zhen-Lin Y.: „Wear mechanisms of TiN-TiB2 ceramics in sliding against alumina from room temperature to 700ºC”, Ceram. Int., 36, (2010), 2129-2135.
- [5] Munro R.: „Material Properties of Titanium Diboride”, Journal of Research of the National Institute of Standards and technology, 105, 5, (2000), 709-720.
- [6] Weimin W., Zhengyi F., Hao W., Runzhang Y.: „Influence of hot pressing sintering temperature and time on microstructure and mechanical properties of TiB2 ceramics”, J. Eur. Ceram. Soc., 22, (2002), 1045-1049.
- [7] Matkovich V.I.: „Boron and refractory borides”, Springer, Berlin (1997), 172.
Typ dokumentu
Bibliografia
Identyfikator YADDA
bwmeta1.element.baztech-article-AGH1-0028-0085