PL EN


Preferencje help
Widoczny [Schowaj] Abstrakt
Liczba wyników
Tytuł artykułu

Maximizing the productivity of a gas melting furnace with regard to the ecological efficiency of its operation

Treść / Zawartość
Identyfikatory
Warianty tytułu
Języki publikacji
EN
Abstrakty
EN
Due to the implementation of environmental regulations and the continual tightening up of the limits for pollutants in combustion systems, we are being forced to pay more attention to this area. A significant source of pollutants originating from the industry is, in particular, the formation of carbon dioxide (CO2) and nitrogen oxides (NOx) in combustion systems with air intake. The control of pollutant emissions has become a global concern due to the worldwide increase in the use of fossil fuels. Besides the fact that the insufficient combustion process has a significant share of emissions in the environment, it also reduces the overall efficiency and economy of the operation using this energy source. We encounter this problem also in the operation of gas melting furnaces. Therefore, the aim of this paper was to describe the results of experimental measurements of the amount of emissions produced during the gas melting furnace KOV 010/1998 operation, which is in practice predominantly used for the melting of Aluminium alloys. Experimental measurements were performed to design the most appropriate operating mode variant of the melting furnace with regard to maximizing its productivity and at the same time to minimizing the total amount of emissions produced during one melting cycle.
Słowa kluczowe
Wydawca
Rocznik
Tom
Strony
292--297
Opis fizyczny
Bibliogr. 29 poz., rys., tab.
Twórcy
  • Technical University of Kosice with a seat in Prešov Faculty of Manufacturing Technologies Department of Automotive and Manufacturing Technologies Štúrova 31, Prešov, Slovak Republic
autor
  • Technical University of Kosice with a seat in Prešov Faculty of Manufacturing Technologies Department of Industrial Engineering and Informatics Bayerova 1, Prešov, Slovak Republic
  • Technical University of Kosice with a seat in Prešov Faculty of Manufacturing Technologies Department of Automotive and Manufacturing Technologies Štúrova 31, Prešov, Slovak Republic
  • Technical University of Kosice with a seat in Prešov Faculty of Manufacturing Technologies Department of technical systems design and monitoring Štúrova 31, Prešov, Slovak Republic
Bibliografia
  • [1] S.H. Al-Jibouri. “Monitoring systems and their effectiveness for project cost control in construction.” International Journal of Project Management, vol. 21, pp. 145-154, 2003.
  • [2] P. Baron, A. Panda, M. Pollák and T. Cmorej. “Modification of production process structure and optimization of material flow for selected types of components computer simulation means.” MM Science Journal, vol. 2017(11), pp. 1895-1900, 2017.
  • [3] S. Banerjee, D. Sanyal, S. Sen and I.K. Puri. “A methodology to control direct-fired furnaces.” International Journal of Heat and Mass Transfer, vol. 47, pp. 5247-5256, 2004.
  • [4] B.S. Brewster, B.W. Webb, M.Q. McQuay, M. D’Agostini and C.E. Baukal. “Combustion measurements and modeling in an oxygen-enriched aluminum-recycling furnace.” The International Journal of Energy, vol. 74, pp. 11-17, 2001.
  • [5] I. Čorný. “Overview of progressive evaluation methods for monitoring of heat production and distribution.” Procedia Engineering, vol. 190, pp. 619-626, 2016.
  • [6] J. Dubják, J. Piteľ and M. Majovská.” Diagnostics of aluminum alloys melting temperature in high pressure casting.” Key Engineering Materials, vol. 669, pp. 110-117, 2016.
  • [7] M.W. Edward, L.S. Donald and O. Ken. “Evaluating aluminum melting furnace transient energy efficiency.” in Proceedings of Symposia held during TMS 2009, Annual Meeting and Exhibition, Warrendale TMS, 2009, pp. 43-51.
  • [8] E. Faltinová, et al. “Reliability analysis of crane lifting mechanism.” Scientific journal of silesian university of technology-series transport, vol. 98, pp. 15-26, 2018.
  • [9] B. Golchert, P. Ridenour, W. Walker, M. Gu, N.K. Selvarasu and C. Zhou. “Effect of nitrogen and oxygen concentrations on Nox emissions in an aluminum furnace.” in Proc. ASME-IMECE, IMECE2006-15693, USA, 2006, pp. 323-333.
  • [10] T.X. Li, M. Hassan, K. Kuwana, K. Saito and P. King. “Performance of secondary aluminum melting: Thermodynamic analysis and plant-site experiments.” Energy, vol. 31(12), pp. 1433-1443, 2006.
  • [11] T. Krenický, J. Ružbarský and A. Panda. “Operation and Diagnostics of Machines and Production Systems Operational States 3.” Key Engineering Materials, vol. 669, pp. 596, 2016.
  • [12] L. Lazic, A. Varga and J. Kizek. “Analysis of combustion characteristic in an aluminum melting furnace.” Metalurgija, vol. 44(3), pp. 192-199, 2005.
  • [13] J. Maščenik. “Implementation of the designed program for calculation and check of chain gears.” MM Science Journal, vol. 2019(december), pp. 3431-3434, 2019.
  • [14] M. Miškiv-Pavlík, J. Jurko, K. Židek, A. Hošovský and K. Monková. “Measurement of distance and displacement by non-contact confocal sensors.” Studia i Materiały, vol. 39(1), pp. 6-12, 2019.
  • [15] A. Mukhopadhyay, I.K. Puri, S. Zelepouga and D.M. Rue. “Numerical simulation of methane-air nozzle burners for aluminum remelt furnaces.” in Proc. ASME-IMECE, HTD24234, USA, 2001, pp. 65-71.
  • [16] A.O. Nieckele, M.F. Naccache and M.S.P. Gomes. “Numerical simulation of a three dimensional aluminum melting furnace.” Journal of Energy Resources, vol. 126, pp. 72-81, 2004.
  • [17] A.O. Nieckele, M.F. Naccache and M.S.P. Gomes. “Combustion performance of an aluminum melting furnace operating with natural gas and liquid fuel.” Applied Thermal Engineering, vol. 31, pp. 841-851, 2011.
  • [18] A. Panda, et al. “Production by FDM method RP technology from PLA eco-materials extruded horizontally in length.” MM Science Journal, vol. 2018(3), pp. 2179-2182, 2018.
  • [19] A. Panda, M. Hatala, K. Dyadyura, J. Duplák and A. Yunak. “Machinability Research by New Abrasion-Resistant Cast Irons Cutting.” Key Engineering Materials, vol. 669, pp. 118-12, 2016
  • [20] I. Pandová and R. Bielousová. “Methods for the protection of the exterior air under emissions of oxides of nitrogen.” Studia i Materiały, vol. 38(6), pp. 65-68, 2018.
  • [21] S. Pavlenko, J. Maščenik and T. Krenický. Worm gears: general information, calculations, dynamics and reliability. Lüdenscheid: RAM-Verlag, 2018, pp. 167.
  • [22] M. Pollák and J. Tkáč. “Enterprise information data management system for small manufacturing company.” TEM Journal - Technology, Education, Management, Informatics, vol. 8(4), pp. 1169-1175, 2019.
  • [23] M. Rimár, M. Fedák, A. Kulikov and P. Šmeringai. “Study of gaseous flows in closed area with forced ventilation.” MM Science Journal, vol. 2018(3), pp. 2188-2191, 2018.
  • [24] L. Sukhodub, A. Panda, K. Dyadyura, I. Pandová and T. Krenický. “The design criteria for biodegradable magnesium alloy implants.” MM Science Journal, vol. 2018(December), pp. 2673-2679, 2018.
  • [25] Ľ. Straka and S. Hašová. “The critical failure determination of the constructional parts of autonomous electroerosion equipment by applying Boolean logic.” Academic Journal of Manufacturing Engineering, vol. 14(2), pp. 80-86, 2016.
  • [26] S. Yan, et al. “Study on point bar residual oil distribution based on dense well pattern in Sazhong area.” Journal of Mines, Metals and Fuels, vol. 65(12), pp. 743-748, 2017.
  • [27] J.M. Wanga, H.J. Yana, J.M. Zhoua, S.X Lib and G.Ch. Guib. “Optimization of parameters for an aluminum melting furnace using the Taguchi approach.” Applied Thermal Engineering, vol. 33-43, pp. 33-34, 2012.
  • [28] W. Zhang and X. Wang. “Simulation of the inventory cost for rotable spare with fleet size impact.” Academic Journal of Manufacturing Engineering, vol. 15(4), pp. 124-132, 2017.
  • [29] Instruction manual of flue gas analyser Testo 340.
Uwagi
Opracowanie rekordu ze środków MNiSW, umowa Nr 461252 w ramach programu "Społeczna odpowiedzialność nauki" - moduł: Popularyzacja nauki i promocja sportu (2021).
Typ dokumentu
Bibliografia
Identyfikator YADDA
bwmeta1.element.baztech-aec50c93-8f51-4447-993e-a0e72c63b002
JavaScript jest wyłączony w Twojej przeglądarce internetowej. Włącz go, a następnie odśwież stronę, aby móc w pełni z niej korzystać.