Prototyping of cosmetic prosthesis of upper limb using additive manufacturing technologies

• Autorzy: Radosh A. , Kuczko W. , Wichniarek R. , Górski F.

Identyfikatory

DOI

10.12913/22998624/70995

• Języki publikacji: EN

Abstrakty

EN

This paper describes prototyping of an individualized cosmetic arm prosthesis. Aim of the studies was to obtain an anatomically correct, lightweight prosthesis. It was accomplished using additive manufacturing technology of fused deposition modeling. The data was obtained by 3D scanning. An experimental concept of dual extrusion of two different materials was applied – the prosthesis was divided into an elastic shell and a rigid core, manufactured in one process. Obtained results were positive.

Słowa kluczowe

EN

upper limb; additive manufacturing; cosmetic prosthesis; medical prototype

• Wydawca: Lublin University of Technology ; Polish Society of Ecological Engineering (PTIE), Branch of PTIE in Lublin
• Czasopismo: Advances in Science and Technology. Research Journal
• Rocznik: 2017
• Tom: Vol. 11, no 3
• Strony: 102--108
• Opis fizyczny: Bibligr. 16 poz., fig., tab.

Twórcy

autor

Radosh A.

• Poznan University of Technology, Chair of Production Engineering and Management, Piotrowo 3 St., Poznan, Poland

autor

Kuczko W.

• Poznan University of Technology, Chair of Production Engineering and Management, Piotrowo 3 St., Poznan, Poland

autor

Wichniarek R.

• Poznan University of Technology, Chair of Production Engineering and Management, Piotrowo 3 St., Poznan, Poland

autor

Górski F.

• Poznan University of Technology, Chair of Production Engineering and Management, Piotrowo 3 St., Poznan, Poland

Bibliografia

• 1. Biddiss E., et al. Consumer design priorities for upper limb prosthetics. Disability and Rehabilitation: Assistive Technology, 2(6), 2007, 346-357.
• 2. Gajdoš I., et al. Structure and tensile properties evaluation of samples produced by Fused Deposition Modeling. Open Engineering, 1(6), 2016, 86-89.
• 3. Górski F., et al. Application of polystyrene prototypes manufactured by FDM technology for evaporative casting method. Modern Machinery Science Journal, 2, 2017, 1729-1733.
• 4. Górski F., et al. Choosing optimal rapid manufacturing process for thin-walled products using expert algorithm. Journal of Industrial Engineering and Management, 3(2), 2010, 408-420.
• 5. Górski F., et al. Computation of mechanical properties of parts manufactured by fused deposition modeling using finite element method. Advances in Intelligent Systems and Computing, 368, 2015, 403-413.
• 6. Karbowski K. and Sujka W. Reverse engineering in medicine. Mechanik, 12, 2015, 111-113.
• 7. Kendall F., et al. Development of novel 3D-printed robotic prosthetic for transradial amputees. Prosthetics and Orthotics International, 40(3), 2016, 400-403.
• 8. Kłonica M. and Kuczmaszewski J. Determining the value of surface free energy on the basis of the contact angle:. Advances in Science and Technology Research Journal, 11(1), 2017, 66–74.
• 9. Kłonica M., et al. Polyamide 6 surface layer following ozone treatment. International Journal of Adhesion and Adhesives, 64, 2016, 179–187.
• 10. Pallari J., et al. Design and additive fabrication of foot and ankle-foot orthoses. Proceedings of the 21st Annual International Solid Freeform Fabrication Symposium – An Additive Manufacturing Conference, Austin, United States 2010, 9-11.
• 11. 11. Pezzin L.E., Dillingham T.R., MacKenzie E.J., Ephraim P., Rossbach P. Use and satisfaction with prosthetic limb devices and related services. Archives of Physical Medicine and Rehabilitation, 85(5), 2004, 723-729.
• 12. 12. Website: Open Bionics; Ada Hand Kit; https://www. openbionics.com/shop/ada (access: 20.03.2017).
• 13. 13. Website: Students develop 3-D printed exoskeletons as part of Mountaintop project; http://thebrownandwhite.com/2015/09/17/3d-printed-exoskeletons-mountaintop/ (access: 20.03.2017).
• 14. 14. Website: The Agency for Health Technology Assessment and Tariff System - H72 H74 Report; http://www. aotm.gov.pl/www/wp-content/uploads/taryfikacja/2016/projekty_taryf/raporty/40/WT.521.17.2016_ H72_H74_raport.pdf (access: 20.03.2017).
• 15. 15. Website: The limbitless arm; http://enablingthefuture.org/upper-limb-prosthetics/the-limbitless-arm/ (access: 20.03.2017).
• 16. 16. Zuniga J., et al. Cyborg beast: A low-cost 3d-printed prosthetic hand for children with upper-limb differences. BMC Research Notes, 8, 2015, 10.

Uwagi

Opracowanie ze środków MNiSW w ramach umowy 812/P-DUN/2016 na działalność upowszechniającą naukę (zadania 2017)