Crystallographic Texture and Grain Refinement in the CuCr Alloy Deformed by SPD Method

• Autorzy: Urbańczyk-Gucwa A. , Brzezińska A. , Adamczyk-Cieślak B. , Rodak K.

Identyfikatory

DOI

10.24425/amm.2019.130127

• Języki publikacji: EN

Abstrakty

EN

Microstructure and texture of the CuCr0.6 alloy processed by rolling with cyclic movement of rolls (RCMR) at room temperature were investigated. The RCMR processing was applied for the samples in different initial conditions in the solid solution followed by quenching into iced water at 1000°C for 3 h and in aging treatment conditions performed at 500°C for 2 h and at 700°C for 24 h. Application of the solution and aging processes prior to RCMR deformation results in the partial dissolution of Cr particles into the Cu matrix and precipitation of the second phase particles. RCMR processing with value of the total effective strain (ε_ft) of 5 was introduced to the material. It was found that the RCMR method is effective in texture weakening. The obtained results revealed that there is a large similarity in texture orientations after RCMR processing independently of heat treatment conditions. Cyclic character of deformation leads to an incomplete transition of LAB to HAB.

Słowa kluczowe

EN

severe plastic deformation; heat treatment; microstructure; texture; CuCr0.6 alloy

• Wydawca: Institute of Metallurgy and Materials Science of Polish Academy of Sciences ; Committee of Materials Engineering and Metallurgy of Polish Academy of Sciences
• Czasopismo: Archives of Metallurgy and Materials
• Rocznik: 2019
• Tom: Vol. 64, iss. 4
• Strony: 1563--1568
• Opis fizyczny: Bibliogr. 26 poz., fot., rys., tab.

Twórcy

autor

Urbańczyk-Gucwa A.

• Silesian University of Technology, Faculty of Materials Engineering and Metallurgy, 40-019 Katowice, Krasińskiego Street 8, Poland

autor

Brzezińska A.

• Silesian University of Technology, Faculty of Materials Engineering and Metallurgy, 40-019 Katowice, Krasińskiego Street 8, Poland

autor

Adamczyk-Cieślak B.

• Warsaw University of Technology, Department of Materials Science and Engineering, 02-507 Warsaw, Wołoska Street 141, Poland

autor

Rodak K.

• Silesian University of Technology, Faculty of Materials Engineering and Metallurgy, 40-019 Katowice, Krasińskiego Street 8, Poland

Bibliografia

• [1] A. Mishra, V. Richard, F. Grégori, R. J. Asaro, M. A. Meyers, Mater. Sci. Eng. A 410-411, 290-298 (2005). DOI: 10.1016/J.MSEA.2005.08.201
• [2] R. K. Islamgaliev, V. D. Sitdikov, K. M. Nesterov, D. L. Pankratov, Rev. Adv. Mater. Sci. 39, 61-68 (2014).
• [3] J. Bogucka, Arch. Metall. Mater. 59, 127-131 (2014). DOI: 10.2478/amm-2014-0020
• [4] K. Edalati, K. Imamura, T. Kiss, Z. Horita, Mater. Trans. 53, 123-127 (2012). DOI: 10.2320/matertrans.MD201109
• [5] R.Z.V.R.K. Islamgaliev, K. M. Nesterov, J. Bourgon, Y. Champion, J. Appl. Physic. 115, 194301-194304 (2014).
• [6] K. Rodak, A. Brzezińska, R. Molak, Mater. Sci. Eng. A (2018). DOI: 10.1016/j.msea.2018.03.
• [7] W. Głuchowski, J. Domagała-Dubiel, J. Sobota, J. Stobrawa, Z. Rdzawski, Arch. Mater. Sci. Eng. 60, 53-63 (2013).
• [8] B. Tolaminejad, A. K. Taheri, M. Shahmiri, H. Arabi, Int. J. Mod. Phys. Conf. Ser. 05, 325-334 (2012). DOI: 10.1142/S201019451200219X
• [9] P. Z. Rodak K., Molak R. M., Phys. Status Solidi C-Curent Top. Solid State Phys. 7, 1351-1354 (2010).
• [10] A. L. Etter, T. Baudin, C. Rey, R. Penelle, Mater. Charact. 56, 19-25 (2006). DOI: 10.1016/j.matchar.2005.09.003
• [11] V. M. Segal, Mater. Sci. Eng. A 406, 205-216 (2005). DOI: 10.1016/J.MSEA.2005.06.035
• [12] L. S. Tóth, B. Beausir, C. F. Gu, Y. Estrin, N. Scheerbaum, C.H.J. Davies, Acta Mater. 58, 6706-6716 (2010). DOI: 10.1016/J.ACTAMAT.2010.08.036
• [13] A. D. Kammers, T. G. Langdon, 29, 1664-1674 (2014). DOI: 10.1557/jmr.2014.207
• [14] H. Lanjewar, L. Kestens, P. Verleysen, EPJ Web Conf. 183, 03008 (2018). DOI: 10.1051/epjconf/201818303008
• [15] J. Yan, J. Ma, J. Wang, Y. Shen, Metall. Mater. Trans. A 49, 5333-5338 (2018). DOI: 10.1007/s11661-018-4874-y
• [16] K. Hamad, Y. G. Ko, Sci. Rep. 6, 29954 (2016). DOI: 10.1038/srep29954
• [17] N. Nadammal, S. V. Kailas, J. Szpunar, S. Suwas, Mater. Charact. 140, 134-146 (2018). DOI: 10.1016/j.matchar.2018.03.044
• [18] K. Rodak, A. Urbańczyk-Gucwa, M. B. Jabłońska, Arch. Civ. Mech. Eng. 18, 500-507 (2018). DOI: 10.1016/j.acme.2017.07.001
• [19] A. Urbańczyk-Gucwa, K. Rodak, A. Płachta, J. Sobota, Z. Rdzawski, Characteristic structure of Cu-0.8Cr alloy using SPD deformation by rolling with cyclic movement of rolls method, 2016. DOI: 10.4028/www.scientific.net/KEM.682.3
• [20] K. Rodak, A. Urbańczyk-Gucwa, K. Radwański, A. Phys. Pol. A. 130, (2016). DOI: 10.12693/APhysPolA.130.1151
• [21] L. G. Schulz, J. Appl. Phys. 20, 1030-1033 (1949). DOI: 10.1063/1.1698268
• [22] http://www.labosoft.com.pl, (b.d.).
• [23] B. A. Richter, K. Chruściel, J. Długopolski, (b.d.).
• [24] D. Hughes, N. Hansen, Acta Mater. 48, 2985-3004 (2000). DOI: 10.1016/S1359-6454(00)00082-3
• [25] X. Huang, Scr. Mater. 38, 1697-1703 (1998). DOI: 10.1016/S1359-6462(98)00051-7
• [26] K. Rodak, J. Pawlicki, Mater. Charact. (2014). DOI: 10.1016/j.matchar.2014.05.002

Uwagi

EN

The work was supported by the National Science Centre of Poland (project No. UMO-2013/09/B/ST8/01695).