Influence of High Pressure-High Temperature Method on the Selected Mechanical Properties of Steel AISI 316L with 2% TiB2

Kurtyka, P.; Sulima, I.; Hyjek, P.; Jaworska, L.

doi:10.24425/amm.2019.130130

Artykuł - szczegóły

Tytuł artykułu

Influence of High Pressure-High Temperature Method on the Selected Mechanical Properties of Steel AISI 316L with 2% TiB2

Autorzy

Kurtyka P. , Sulima I. , Hyjek P. , Jaworska L.

Treść / Zawartość

Pełne teksty:

Pobierz

Identyfikatory

DOI

10.24425/amm.2019.130130

Warianty tytułu

Języki publikacji

Abstrakty

AISI 316L/TiB₂/2p composites were manufactured by HP-HT using different pressures (5 and 7 GPa) and temperatures (900-1300°C), with constant reinforcing particle content 2 vol%. The mechanical properties of the composites were evaluated on the basis of hardness (HV0.3) and compression tests (20°C, 10^-5 s^-1). The results showed that the role of sintering pressure increased with increasing process temperature. At temperatures of 900°C and pressures of 5 and 7 GPa the difference in measured values of compressive strength was 1-2%, while at 1300°C they reached 20%. At constant pressure of 5 GPa, a change in hardness and compressive strength of 40% were obtained with a temperature change of 900 to 1300°C. Changes in mechanical properties in the composite occurred without substantial changes in density, microstructure, reinforcement phase distribution, and phase composition in the matrix.

Słowa kluczowe

high pressure-high temperature physical properties mechanical properties steel matrix composites titanium diboride

Wydawca

Institute of Metallurgy and Materials Science of Polish Academy of Sciences
Committee of Materials Engineering and Metallurgy of Polish Academy of Sciences

Czasopismo

Archives of Metallurgy and Materials

Rocznik

2019

Tom

Vol. 64, iss. 4

Strony

1585--1592

Opis fizyczny

Bibliogr. 54 poz., fot., rys., tab., wzory

Twórcy

autor

Kurtyka P.

Pedagogical University of Krakow, Institute of Technology, 2 Podchorazych Str., 30-084, Kraków, Poland

autor

Sulima I.

iwona.sulima@up.krakow.pl

Pedagogical University of Krakow, Institute of Technology, 2 Podchorazych Str., 30-084, Kraków, Poland

autor

Hyjek P.

AGH University of Science and Technology, Faculty of Non-Ferrous Metals, Al. Mickiewicza 30, 30-059 Kraków, Poland

autor

Jaworska L.

AGH University of Science and Technology, Faculty of Non-Ferrous Metals, Al. Mickiewicza 30, 30-059 Kraków, Poland

Bibliografia

[1] B. Basu, G. B. Raju, A. K. Suri, Inter. Mater. Rev. 51 (6), 352-374 (2013).
[2] V. I. Matkovich, Boron and Refractory Borides, Springer Science & Business Media, Berlin, Heidelberg (2012).
[3] R. Koonigshofer, S. Fuurnsinn, P. Steinkellner, W. Lengauer, R. Haas, K. Rabitsch, M. Scheerer, Inter. J. Ref. Met. Hard Mater. 23 (4-6), 350-357 (2005).
[4] N. R. Baddoo, J. Constr. Steel Res. 64 (11), 1199-1206 (2008).
[5] P. Marshall, Austenitic Stainless Steels, Microstructure and mechanical properties, Springer Science & Business Media (1984).
[6] A. Fedrizzi, M. Pellizzari, M. Zadra, E. Marin, Microstructural study and densification analysis of hot work tool steel matrix composites reinforced with TiB2 particles, Mater. Char. 86, 69-79 (2013).
[7] E. Olejnik, L. Szymanski, P. Kurtyka, T. Tokarski, B. Grabowska, P. Czapla, Archives of Foundry Engineering 16 (2), 89-94 (2016).
[8] B. Li, Y. Liu, J. Li, H. Cao, L. He, J. Mater. Process Tech. 210 (1), 91-95 (2010).
[9] I. Sulima, R. Kowalik, Mater. Sci. Eng. A 639, 671-680 (2015).
[10] I. Sulima, L. Jaworska, P. Figiel, Arch. Metall. Mater. 59 (1), 205-209 (2014).
[11] I. Sulima, G. Boczkal, Mater. Sci. Eng. A 644, 76-78 (2015).
[12] V. Viswanathan, T. Laha, K. Balani, A. Agarwal, S. Seal, Mater. Sci. Eng. R-Reports 54 (5-6), 121-285 (2006).
[13] E. Olejnik, G. Sikora, S. Sobula, T. Tokarski, B. Grabowska, Materials Science Forum 782, 527-532 (2014).
[14] E. Olejnik, L. Szymanski, P. Kurtyka, T. Tokarski, W. Maziarz, B. Grabowska, P. Czapla, Archives of Foundry Engineering 16 (3), 77-82 (2016).
[15] E. Fraś, A. Janas, P. Kurtyka, S. Wierzbinski, Arch. Metall. Mater. 48, 384-408 (2003).
[16] E. Fras, A. Janas, P. Kurtyka, S. Wierzbinski, Arch. Metall. Mater. 49, 113-141 (2004).
[17] L. Blaz, M. Sugamata, J. Kaneko, J. Sobota, G. Wloch, W. Bochniak, A. Kula, J. Mater. Proc. Tech. 209 (9), 4329-4336 (2009).
[18] K. Bryla, J. Dutkiewicz, L. Litynska-Dobrzynska, L. L. Rokhlin, P. Kurtyka, Arch. Metall. Mater. 57 (3), 711-717 (2012).
[19] B. Mani, M. H. Paydar, J. Alloys Comp. 492 (1-2), 116-121 (2010).
[20] K. Bryla, J. Dutkiewicz, L. L. Rokhlin, L. Litynska-Dobrzynska, K. Mroczka, P. Kurtyka, Arch. Metall. Mater. 58 (2), 481-487 (2013).
[21] R. S. Mishra, Z. Y. Ma, Mater. Sci. Eng. R-Reports 50 (1-2), 1-78 (2005).
[22] G. J. Fernandez, L. E. Murr, Mater. Charact. 52 (1) 65-75 (2004).
[23] P. Kurtyka, N. Rylko, T. Tokarski, A. Wojcicka, A. Pietras, Comp. Structure 133, 959-967 (2015).
[24] L.-W. Yin, Z.-D. Zou, M.-S. Li, Y.-X. Liu, Z.-Y. Hao, App. Phys. A 71 (4), 457-459 (2000).
[25] P. Klimczyk, V. S. Urbanovich, Arch. Mater. Sci. Eng. 39 (2), 92-96 (2009).
[26] J. Pantic, V. Urbanovich, V. Poharc-Logar, B. Joki, M. Stojmenovi, A. Kremenovi, B. Matovi, Phys. Chem. Minerals 41 (10), 775-782 (2014).
[27] P. Wyzga, L. Jaworska, M. Bucko, P. Putyra, A. Kalinka, Composites 11 (1), 34-38 (2011).
[28] F. Bundy, Ultra-high pressure apparatus, Physics Reports 167 (3), 133-176 (1988).
[29] M. Eremets, High Pressure Experimental Methods, Oxford Science Publications, Oxford University Press, (1996).
[30] L. Jaworska, Materials Engineering 2, 72-75 (1999).
[31] T. Pieczonka, J. Kazior, A. Tiziani, A. Molinari, J. Mater. Proc. Techn. 64 (1-3), 327-334 (1997).
[32] G. S. Upadhyaya, S. K. Mukherjee, Mater. Des. 6 (6), 323-327 (1985).
[33] I. Sulima, P. Klimczyk, P. Hyjek, Arch. Mater. Sci. Eng. 39 (2), 103-106 (2009).
[34] D. C. Ludwigson, Metall. Trans. 2 (10), 2825-2828 (1971).
[35] H. J. Hollomon, Tensile deformation, Transactions of the Metallurgical Society of AIME 162, 268-290 (1945).
[36] D. Lee, Metall. Trans. 1 (6), 1607-1616 (1970).
[37] C. Sellars, W. M. Tegart, Inter. Mater. Rev. 17, 1-23 (1972).
[38] D. J. Drobnjak, J. G. Parr, Metall. Trans. 1 (4), 759-765 (1970).
[39] M. Selin, Metal. Mater. Trans. A 41 (11), 2805-2815 (2010).
[40] S. S. Wu, S. Y. Chen, D. Gan, Mater. Sci. Eng. A 127 (2), L1-L5 (1990).
[41] J. W. Simmons, Metall. Mater. Trans. A 26 (10), 2579-2595 (1995).
[42] J. Lesage, D. Chicot, O. Bartier, M. A. Zampronio, P.E.V. de Miranda, Mater. Sci. Eng. A 282 (1), 203-212 (2000).
[43] E. I. Samuel, B. K. Choudhary, K. Rao, Scr. Mater. 46 (7), 507-512 (2002).
[44] D. J. Lloyd, Scr. Mater. 48 (4) 341-344 (2003).
[45] B. Inem, Mater. Sci. Eng. A 197 (1), 91-95 (1995).
[46] K. G. Samuel, Journal Phys. D: Applied Physics 39 (1), 203-212 (2005).
[47] S. Hertele, W. De Waele, R. Denys, Int. J. Non-Linear Mech. 46 (3), 519-531 (2011).
[48] B. P. Kashyap, K. Tangri, Acta Metall. Mater. 43 (11), 3971-3981 (1999).
[49] N. Kurgan, Mater. Des. 55, 235-241 (2014).
[50] B. Verlee, T. Dormal, J. Lecomte-Beckers, Pow. Metall. 55 (4), 260-267 (2012).
[51] M. Dewidar, Inter. J. Mech. Mech. Eng. 12 (1), 10-24 (2012).
[52] A. Szymanska, D. Oleszak, A. Grabias, M. Rosinski, K. Sikorski, J. Kazior, A. Michalski, K. J. Kurzydlowski, Rev. Adv. Mater. Sci. 8 (2), 143-146 (2004).
[53] Z. G. Liu, X. J. Hao, K. Masuyama, K. Tsuchiya, M. Umemoto, S. M. Hao, Scr. Mater. 44 (8-9) 1775-1779 (2001).
[54] M. Umemoto, Z. Liu, Y. Xu, K. Tsuchiya, Metall. Mater. Trans. A 33 (7) 2195-2203 (2002).

Uwagi

The authors would like to thank Institute of Advanced Manufacturing Technology in Cracow, for her help in the HP-HT sintering of the composites. This work has been founded by the Research Fund of the Faculty of Mathematics, Physics and Technical Science of Pedagogical University of Krakow.

Typ dokumentu

Bibliografia

Identyfikator YADDA

bwmeta1.element.baztech-a8846fbd-b5f0-47b5-b360-4de4a31719a5