Mechanical properties and fatigue life detection of copper particle filled polyester composite material under rotating bending load

• Autorzy: Hamzah Ahmed Fadhil , Al-Turaihi Ali S. , Hunain Mustafa Baqir , Fadhel Essam Zuheir

Identyfikatory

DOI

10.29354/diag/140001

• Języki publikacji: EN

Abstrakty

EN

In the present investigation, the fatigue life detection of composite material by adding copper particle of about than 25 μm diameter with 5, 10, 15 % volume fraction, as a reinforcements into the unsaturated polyester polymer composite material on fatigue life detection of composite material were studied experimentally and numerically. Composites were made using hand lay-up technique and evaluated for mechanical and fatigue properties in accordance with ASTM standards. The experimental results of the tensile test showed that adding 15% of copper particle in unsaturated polyester gives maximum ultimate tensile stress. Fatigue tests including test rod specimens made of composite materials under completely reversed cyclic loading in a rotating cantilever reversed bending machine. It is found that, the fatigue life and fatigue strength increase with increasing in the copper percentage volume fraction in unsaturated polyester resin compared with pure polyester composites. The experimental work was compared with numerical work, which was done by using ANSYS/19 and good agreement has been found. The maximum overall difference between the experimental and numerical work was around 9 %.

Słowa kluczowe

EN

polymer matrix composite; particle copper reinforcement; tensile strength; fatigue

PL

kompozyt polimerowy; wytrzymałość na rozciąganie; zmęczenie

• Wydawca: Polskie Towarzystwo Diagnostyki Technicznej
• Czasopismo: Diagnostyka
• Rocznik: 2021
• Tom: Vol. 22, No. 3
• Strony: 35--42
• Opis fizyczny: Bibliogr. 21 poz., rys., tab.

Twórcy

autor

Hamzah Ahmed Fadhil

• Department of Engineering of Polymer and Petrochemical Industries / Faculty of Materials Engineering/University of Babylon

autor

Al-Turaihi Ali S.

• Mechanical Engineering Department/Faculty of Engineering/University of Babylon

autor

Hunain Mustafa Baqir

• Mechanical Engineering Department/Faculty of Engineering/University of Babylon

autor

Fadhel Essam Zuheir

• Mechanical Engineering Department/Faculty of Engineering/University of Babylon

Bibliografia

• 1. Bora B. Design and analysis filament wound composite tubes. m. sc thesis. Mechanical Engineering Department, The Graduate School of Natural and Applied Science. Middle East Technical university. 2004.
• 2. Richardson T. Composites-a design guide. Industrial Press Inc. 200 Madison Avenue,Newyork. 1987.
• 3. Antunes FV, Ferreira JM, Costa JD, Capela C. Fatigue life predictions in polymer particle composites. International Journal of Fatigue 2002; 24: 1095-1105.
• 4. Basaran C, Nie S, Hutchins CS, Ergun H. Influence of interfacial bond strength on fatigue life and thermo-mechanical behavior of a particulate composite: an experimental study. International Journal of Damage Mechanics. 2008;17:123-147. http://dx.doi.org/10.1177/1056789507077437.
• 5. Swapan K. Bhattacharyya, Sadhan KD, Sanjay B. Studies on Poly(Viny1 Chloride)-Copper Composites. Part 1: State of Segregation of Filler Particles, Electrical and Mechanical Properties in Presence of Plasticizer and Stabilizer. Polymer Engineering And Science. 1979; 19(8): 533-539.
• 6. Sufyan Garoushi, Lippo VJ, Lassila, Arzu Tezvergil, Pekka K, Vallittu. Static and fatigue compression test for particulate filler composite resin with fiberreinforced composite substructure. Dental Materials. 2007; 23: 17-23.
• 7. Hyonny Kim, Myounggu Park, Kelli Hsieh. Fatigue fracture of embedded copper conductors in multifunctional composite structures. Composites Science and Technology. 2006; 66: 1010-1021.
• 8. Mohammed Abdulsattar Mohammed. Mechanical behavior for polymer matrix composite reinforced by copper powder. Nahrain University. College of Engineering Journal (NUCEJ). 2011; 14(2): 160-176.
• 9. Ali S. Al-Turaihi, Mustafa Baqir Hunain, Ahmed Fadhil Hamzah, Essam Zuheir Fadhel. Experimental and numerical investigation of fatigue behavior of chopped GFRP composite rod under rotating bending load. Journal of Mechanical Engineering Research and Developments. 2021; 44(2): 324-335.
• 10. Mustafa Baqir Hunain, Ali S. Al-Turaihi, Salah N. Alnomani. Tensile And Charpy Impact behavior of eglass / unsaturated polyester laminated composite material at elevated temperature. Journal of Engineering Science and Technology. 2021; 16(2): 1547-1560.
• 11. Srivastava VK, Verma A. Mechanical behaviour of copper and aluminium particles reinforced epoxy resin composites. American Journal of Materials Science. 2015;5(4):84-89. http://dx.doi.org/10.5923/j.materials.20150504.02.
• 12. Chan KL, Mariatti M, Lockman Z, Sim LC. Effects of the size and filler loading on the properties of copper-and silver-nanoparticle-filled epoxy composites. Journal of Applied Polymer Science. 2011;121:3145-3152. https://doi.org/10.1002/app.33798.
• 13. Cheang P, Khor KA. Effect of particulate morphology on the tensile behaviour of polymer/hydroxyapatite composites. Materials Science and Engineering A345. 2003; 47-54.
• 14. Luyt AS, Molefi JA, Krump H. Thermal, mechanical and electrical properties of copper powder filled lowdensity and linear low-density polyethylene composites. Polymer Degradation and Stability. 2006;91:1629-1636. http://dx.doi.org/10.1016/j.polymdegradstab.2005.09.014.
• 15. Mohamad Nur Fuadi Pargi, Pei Leng Teh, Salmah Hussiensyah, Cheow Keat Yeoh and Supri Abd Ghani. Recycled-copper-filled epoxy composites: the effect of mixed particle size. International Journal of Mechanical and Materials Engineering. 2015;10(3): 1-10. http://dx.doi.org/10.1186/s40712-015-0030-2.
• 16. Quickmast 105 Data Sheet. http://www.dcpint.com.
• 17. Hayder MH. AL-Shukri. Experimental and Theoretical Investigation into Some Mechanical Properties of Glass Polyester Composite Under Static and Dynamic Loads. M.Sc thesis. Educational Technology/Mechanical Engineering Department, University of Technology, Baghdad, Iraq. 2007.
• 18. ASTM D638 / D638M-95. Standard specification for asbestos tubular sleeving. ASTM International, West Conshohocken, PA, 2017. http://www. astm.org.
• 19. GUNT. WP 140 Fatigue Testing Apparatus. Publication No.: 912.00000A 140 12. 2009. http://www.gunt.de.
• 20. Namik K. Alpaydin, Halit S. Turkmen. The Dynamic Response of the Sandwich Panel Subjected to the Impact Load. IEEE Xplore. 2009: 176-180. http://www.ivsl.org.
• 21. Abdul Jabar H. Ali, A non-linear damage model for fatigue life prediction of fiber reinforced polymer composite lamina at different temperatures. Ph.D. Theses, University of Technology. Mechanical Engineering Department. Baghdad. Iraq. 2013.

Uwagi

Opracowanie rekordu ze środków MEiN, umowa nr SONP/SP/546092/2022 w ramach programu "Społeczna odpowiedzialność nauki" - moduł: Popularyzacja nauki i promocja sportu (2022-2023).