Influence of Al2O3 nanoparticle mass concentration and aerosol formation parameters on tool vibration during turning of Ti6Al4V titanium alloy

• Autorzy: Dylewicz Weronika , Szczotkarz Natalia , Maruda Radosław , Gupta M. K.

Identyfikatory

DOI

10.59441/ijame/189470

• Języki publikacji: EN

Abstrakty

EN

Machining difficult-to-cut materials involves challenging machining conditions, including higher temperatures in the cutting zone, cutting forces and friction. Another important phenomenon is vibration, which is undesirable when manufacturing high quality workpieces. One way to reduce vibration in the cutting zone is to use cooling methods. Due to its environmentally friendly nature, the minimum quantity lubrication (MQL) method has already been widely used in metalworking. However, when combined with nanofluids, it improves the ability of the aerosol to dissipate more heat and increase lubrication in the cutting zone. This paper presents the effect of a polyol ester-based Al2O3 nanofluid due to the varying mass concentration of nanoparticles on the vibration during turning of Ti6Al4V alloy and compares the results with dry cutting and the MQL method without nanoparticles. Four concentrations (0.25−1 wt%), variable nanofluid flow rate E = 0.388−1.182 g/min and air flow rate P = 10−40 l/min were considered. According to the statistical analysis, the most important factor influencing tool vibration was the mass concentration of nanoparticles in the cutting fluid. By combining the MQL method with 0.5 wt% Al2O3, the vibration acceleration RMS values were found to be the lowest. When compared to the MQL method without nanoparticles, the RMS values for dry cutting ranged from 17.8% to 24.9%, and for wet cutting they were reduced by about 10.9-18.5%.

Słowa kluczowe

EN

Al2O3 nanoparticles; nanofluids; MQL; vibrations; variable air flow rate; variable nanofluid flow rate

PL

nanocząsteczka; wibracje; przepływ powietrza

• Wydawca: Oficyna Wydawnicza Uniwersytetu Zielonogórskiego
• Czasopismo: International Journal of Applied Mechanics and Engineering
• Rocznik: 2024
• Tom: Vol. 29, no. 2
• Strony: 52--66
• Opis fizyczny: Bibliogr. 33 poz., fot., tab., wykr.

Twórcy

autor

Dylewicz Weronika

• Faculty of Mechanical Engineering, University of Zielona Góra, ul. Prof. Z. Szafrana 4 65-516 Zielona Góra, POLAND

autor

Szczotkarz Natalia

• Faculty of Mechanical Engineering, University of Zielona Góra, ul. Prof. Z. Szafrana 4 65-516 Zielona Góra, POLAND

• https://orcid.org/0000-0003-2313-5437

autor

Maruda Radosław

• Faculty of Mechanical Engineering, University of Zielona Góra, ul. Prof. Z. Szafrana 4 65-516 Zielona Góra, POLAND

autor

Gupta M. K.

• Department of Mechanical Engineering, Graphic Era (Deemed to be university), INDIA
• Faculty of Mechanical Engineering, Opole University of Technology, POLAND

• https://orcid.org/0000-0002-0777-1559

Bibliografia

• [1] Leksycki K., Maruda R.W., Feldshtein E., Wojciechowski S., Habrat W., Gupta M.K. and Królczyk G.M. (2023): Evaluation of tribological interactions and machinability of Ti6Al4V alloy during finish turning under different cooling conditions.− Tribology International, vol.189, Aricle No.109002, https://doi.org/10.1016/j.triboint.2023.109002.
• [2] Leksycki K. and Królczyk J.B. (2021): Comparative assessment of the surface topography for different optical profilometry techniques after dry turning of Ti6Al4V titanium alloy.− Measurement, vol.169, pp.108378, https://doi.org/10.1016/j.measurement.2020.108378.
• [3] Gross D., Blauhöfer M. and Hanenkamp N. (2020): Milling of Ti6Al4V with carbon dioxide as carrier medium for minimum quantity lubrication with different oils.− Procedia Manufacturing, vol.43, pp.439- 446, https://doi.org/10.1016/j.promfg.2020.02.190.
• [4] Wang D. (2023): Research on surface integrity and its influencing factors in the high-speed cutting of typical aluminum/titanium/nickel alloys: a review.− International Journal of Advanced Manufacturing Technology, vol.127, pp.4915-4942, https://doi.org/10.1007/s00170-023-11808-0.
• [5] Khaliq W., Zhang C., Jamil M. and Khan A.M. (2020): Tool wear, surface quality, and residual stresses analysis of micro-machined additive manufactured Ti–6Al–4V under dry and MQL conditions.− Tribology International, vol.151, pp.106408, https://doi.org/10.1016/j.triboint.2020.106408.
• [6] Abbas A.T., Gupta M.K., Soliman M.S., Mia M., Hegab H., Luqman M. and Pimenov D.Y. (2019): Sustainability assessment associated with surface roughness and power consumption characteristics in nanofluid MQL-assisted turning of AISI 1045 steel.− International Journal of Advanced Manufacturing Technology, vol.105, pp.1311-1327, https://doi.org/10.1007/s00170-019-04325-6.
• [7] Ozcelik B., Kuram E., Huseyin Cetin M. and Demirbas E. (2011): Experimental investigations of vegetable based cutting fluids with extreme pressure during turning of AISI 304L.− Tribology International, vol.44, pp.1864-1871, https://doi.org/10.1016/j.triboint.2011.07.012.
• [8] Wojciechowski S., Maruda R.W., Krolczyk G.M. and Niesłony P. (2018): Application of signal to noise ratio and grey relational analysis to minimize forces and vibrations during precise ball end milling.− Precision Engineering, vol.51, pp.582-596, https://doi.org/10.1016/j.precisioneng.2017.10.014.
• [9] Vieira J.M., Machado A.R. and Ezugwu E.O. (2001): Performance of cutting fluids during face milling of steels.− Journal of Materials Processing Technology, vol.16, pp.244-251, https://doi.org/10.1016/S0924-0136(01)01010-X.
• [10] Huang P., Li J., Sun J. and Ge M. (2012): Milling force vibration analysis in high-speed-milling titanium alloy using variable pitch angle mill.− International Journal of Advanced Manufacturing Technology, vol.58, pp.153-160, https://doi.org/10.1007/s00170-011-3380-9.
• [11] Okokpujie I.P., Bolu C.A., Ohunakin O.S., Akinlabi E.T. and Adelekan D.S. (2019): A Review of Recent Application of Machining Techniques, based on the Phenomena of CNC Machining Operations.− Procedia Manufacturing, vol.35, pp.1054-1060, https://doi.org/10.1016/J.PROMFG.2019.06.056.
• [12] Gupta M.K., Niesłony P., Korkmaz M.E., Kuntoğlu M., Królczyk G.M., Günay M. and Sarikaya M. (2023): Comparison of Tool Wear, Surface Morphology, Specific Cutting Energy and Cutting Temperature in Machining of Titanium Alloys Under Hybrid and Green Cooling Strategies.− International Journal of Precision Engineering and Manufacturing-Green Technology, vol.10, pp.1393- 1406, https://doi.org/10.1007/s40684-023-00512-9.
• [13] Gupta M.K., Niesłony P., Sarikaya M., Korkmaz M.E., Kuntoğlu M., Królczyk G.M. and Jamil M. (2022): Tool wear patterns and their promoting mechanisms in hybrid cooling assisted machining of titanium Ti- 3Al-2.5V/grade 9 alloy.− Tribology International, vol.174, pp.107773, https://doi.org/10.1016/j.triboint.2022.107773.
• [14] Sivalingam V., Zhou Q., Selvam B., Sun J., Pandiyan K., Gupta M.K. and Kormaz M.E. (2023): A mathematical approach of evaluating sustainability indicators in milling of aluminium hybrid composite by different eco-friendly cooling strategies.− Sustainable Materials and Technologies, vol.36, pp.e00605, https://doi.org/https://doi.org/10.1016/j.susmat.2023.e00605.
• [15] Gupta M.K., Korkmaz M.E., Sarıkaya M., Krolczyk G.M., Günay M. and Wojciechowski S. (2022): Cutting forces and temperature measurements in cryogenic assisted turning of AA2024-T351 alloy: An experimentally validated simulation approach.− Measurement: Journal of the International Measurement Confederation, vol.188, pp.110594, https://doi.org/10.1016/j.measurement.2021.110594.
• [16] Carou D., Rubio E.M., Lauro C.H. and Davim J.P. (2016): The effect of minimum quantity lubrication in the intermittent turning of magnesium based on vibration signals.− Measurement: Journal of the International Measurement Confederation, vol.94, pp.338-343, https://doi.org/10.1016/j.measurement.2016.08.016.
• [17] Özbek O. and Saruhan H. (2020): The effect of vibration and cutting zone temperature on surface roughness and tool wear in eco-friendly MQL turning of AISI D2.− Journal of Materials Research and Technology, vol.9, pp.2762-2772, https://doi.org/10.1016/j.jmrt.2020.01.010.
• [18] S Swain S., Kumar R., Panigrahi I., Sahoo A.K. and Panda A. (2022): Machinability performance investigation in CNC turning of Ti–6Al–4V alloy: Dry versus iron-aluminium oil coupled MQL machining comparison.− International Journal of Lightweight Materials and Manufacture, vol.5, pp.496-509, https://doi.org/10.1016/j.ijlmm.2022.06.002.
• [19] Sahoo S.P., Datta S., Roy T. and Ghosh S. (2021): Machining performance of Ti6Al4V under dry environment, pressurized air supply and water-MQL: analysis of machining-induced vibration signals and captured thermographs.− Sadhana - Academy Proceedings in Engineering Sciences, vol.46, Article No.208, https://doi.org/10.1007/s12046-021-01738-6.
• [20] Zhong W., Zhao D. and Wang X. (2010): A comparative study on dry milling and little quantity lubricant milling based on vibration signals.− International Journal of Machine Tools and Manufacture, vol.50, pp.1057-1064, https://doi.org/10.1016/j.ijmachtools.2010.08.011.
• [21] Sharma K.A., Tiwari A.K. and Dixit A.R. (2015): Improved Machining Performance with Nanoparticle Enriched Cutting Fluids under Minimum Quantity Lubrication (MQL) Technique: A Review.− Materials Today: Proceedings, vol.2, pp.3545-3551, https://doi.org/10.1016/j.matpr.2015.07.066.
• [22] Kursus M., Liew P.J., Che Sidik N.A. and Wang J. (2022): Recent progress on the application of nanofluids and hybrid nanofluids in machining: a comprehensive review.− International Journal of Advanced Manufacturing Technology, vol.121, pp.1455-1481, https://doi.org/10.1007/s00170-022.
• [23] Hu S., Li C., Zhou Z., Liu B., Zhang Y., Yang M., Li B., Gao T., Liu M., Cui X., Wang X., Xu W., Dambatta Y.S., Li R. and Sharma S. (2023): Nanoparticle-enhanced coolants in machining: mechanism, application, and prospects.− Frontiers of Mechanical Engineering, vol.18, No.4, p.53, https://doi.org/10.1007/s11465-023-0769-8.
• [24] Morshed A., Wu H. and Jiang Z. (2021): A comprehensive review of water-based nanolubricants.− Lubricants, vol.9, No.89, https://doi.org/10.3390/lubricants9090089.
• [25] Kong L., Sun J. and Bao Y. (2017): Preparation, characterization and tribological mechanism of nanofluids.− RSC Advances, vol.7, pp.12599-12609, https://doi.org/10.1039/c6ra28243a.
• [26] Korkmaz M.E., Gupta M.K., Günay M., Boy M., Yaşar N., Demirsöz R., Nimel Sworna Ross K. and Abbas Y. (2023): Comprehensive analysis of tool wear, surface roughness and chip morphology in sustainable turning of Inconel-601 alloy.− Journal of Manufacturing Processes, vol.103, pp.156-167, https://doi.org/10.1016/j.jmapro.2023.08.026.
• [27] Maruda W., Arkusz K., Szczotkarz N., Wojciechowski S., Niesłony P. and Królczyk G.M. (2023): Analysis of size and concentration of nanoparticles contained in cutting fluid during turning of 316L steel in minimum quantity lubrication conditions.− Journal of Manufacturing Processes, vol.87, pp.106-122, https://doi.org/10.1016/j.jmapro.2022.12.065.
• [28] Shuang Y., John M. and Songlin D. (2019): Experimental investigation on the performance and mechanism of graphene oxide nanofluids in turning Ti-6Al-4V.− Journal of Manufacturing Processes, vol.43, 164-174, https://doi.org/10.1016/j.jmapro.2019.05.005.
• [29] Yi S., Li J., Zhu J., Wang X., Mo J. and Ding S. (2020): Investigation of machining Ti-6Al-4V with graphene oxide nanofluids: Tool wear, cutting forces and cutting vibration.− Journal of Manufacturing Processes, vol.49, pp.35-49, https://doi.org/10.1016/j.jmapro.2019.09.038.
• [30] Park K.H., Olortegui-Yume J., Yoon M.C. and Kwon P. (2010): A study on droplets and their distribution for minimum quantity lubrication (MQL).− International Journal of Machine Tools and Manufacture, vol.50, pp.824-833, https://doi.org/10.1016/j.ijmachtools.2010.05.001.
• [31] Venkatesan K., Devendiran S., Ghazaly N.M. and Nishanth. (2019): Application of Taguchi-Response surface analysis to optimize the cutting parameters on turning of Inconel X-750 using Nanofluids suspended Al2O3 in coconut oil.− Procedia Manufacturing, vol.30, pp.90-97, https://doi.org/10.1016/j.promfg.2019.02.014.
• [32] Maruda R.W., Szczotkarz N., Wojciechowski S., Gawlik J. and Królczyk G.M. (2023): Metrological relations between the spray atomization parameters of a cutting fluid and formation of a surface topography and cutting force.− Measurement, vol.219, pp.113255, https://doi.org/10.1016/j.measurement.2023.113255.
• [33] Tiwari S. and Amarnath M. (2023): Improving the machining performance with bio-degradable coconut oil-assisted MQL turning of AISI-1040 steel: a sustainable machining approach.− Biomass Conversion and Biorefiner, https://doi.org/10.1007/s13399-023-04573-3.