Microstructure and Tribological Behavior of Cu-2.5Ti Alloy in Two Different Environments

• Autorzy: Efe Ceren , Sun Yavuz , Türen Yunus , Ahlatci Hayrettin

Identyfikatory

DOI

10.24425/amm.2022.141072

• Języki publikacji: EN

Abstrakty

EN

In this study, the nominal composition of Cu-2.5Ti alloy was thermally treated to obtain homogenized, aged, and 40% prior cold-rolled+ aged samples. The hardness, wear behavior, and microstructure of samples were investigated. The reciprocating wear tests were performed under four different loads under dry and 3.5%NaCl corrosive environments. The alloy reached its highest hardness value of 8 hours for the aged sample. The hardness value of the sample that was homogenized then cold-rolled by 40% and aged was found higher than the other samples. A decrease in the wear rates in dry conditions was observed in homogenized, aged and cold-rolled and aged samples, respectively. This decrease was more in the corrosive environment. Studies can be advanced by examining the wear behavior at different alloy ratios. The effects of different alloying elements and the ratio of cold-rolled before or after aging can also be investigated for future research.

Słowa kluczowe

EN

Cu-Ti alloys; wear behavior; corrosive environment; hardness

• Wydawca: Institute of Metallurgy and Materials Science of Polish Academy of Sciences ; Committee of Materials Engineering and Metallurgy of Polish Academy of Sciences
• Czasopismo: Archives of Metallurgy and Materials
• Rocznik: 2022
• Tom: Vol. 67, iss. 4
• Strony: 1443--1453
• Opis fizyczny: Bibliogr. 26 poz., fot., rys., tab.

Twórcy

autor

Efe Ceren

• Zonguldak Bülent Ecevit University, Gökçebey M. M. Çanakcı Vocational School of Higher Education, Gökçebey, Zonguldak, Turkey

• https://orcid.org/0000-0001-8615-6740

autor

Sun Yavuz

• Karabuk University, Department of Metallurgy and Materials Engineering, Karabuk, Turkey

• https://orcid.org/0000-0002-7336-5591

autor

Türen Yunus

• Karabuk University, Department of Metallurgy and Materials Engineering, Karabuk, Turkey

• https://orcid.org/0000-0001-8755-1865

autor

Ahlatci Hayrettin

• Karabuk University, Department of Metallurgy and Materials Engineering, Karabuk, Turkey

• https://orcid.org/0000-0002-6766-4974

Bibliografia

• [1] W.A. Soffa, D.E. Laughlin, P. Mat. Sci. 49, 347-366.(2004). DOI: https://doi.org/10.1016/S0079-6425(03)00029-X
• [2] A. Szkliniarz, L. Blacha, W. Szkliniarz, J. Labaj, Arch. Metall. Mater. 59, 1307-1312 (2014). DOI: https://doi.org/10.2478/amm-2014-0223
• [3] S. Semboshi, S. Amano, J. Fu, A. Iwase, T. Takasugi, Metallurgical and Materials Transactions A 48, 1501-1511 (2017).
• [4] R. Markandeya, S. Nagarjuna, D.S. Sarma, Mater. Sci. Eng. A 404, 305-313 (2005). DOI: https://doi:10.1016/j.msea.2005.05.072
• [5] S. Kim, M. Kang, J. Ind. and Eng. Chem. 18, 969-978 (2012). DOI: https://doi.org/10.1016/j.jiec.2011.10.009
• [6] S. Nagarjuna, K. Balusabramanian, D.S. Sarma, Mater. Sci. Eng. A 225, 118-124 (1997). DOI: https://doi.org/10.1016/S0921-5093(96)10578-5
• [7] R. Markandeya, S. Nagarjuna, D.S. Sarma, Mater. Charac. 57, 348-357 (2006). DOI: https://doi.org/10.1016/j.matchar.2006.02.017
• [8] A. Szkliniarz, Arch. Metall. Mater. 62, 223-230 (2017). DOI: https://doi.org/10.1515/amm-2017-0033
• [9] S. Nagarjuna, K. Balusabramanian, D.S. Sarma, J. Mater. Sci. 34, 2929-2942 (1999). DOI: https://doi.org/10.1023/A:1004603906359
• [10] S. Nagarjuna, M. Srivinas, Mater. Sci. Eng. A 498, 468-474 (2008). DOI: https://doi.org/10.1016/j.msea.2008.08.029
• [11] S. Nagarjuna, K. Balusabramanian, D. Sarma, J. Mater. Sci. 32, 3375-3385 (1997). DOI: https://doi.org/10.1023/A:1018608430443
• [12] S. Suzuki, K. Hirabayshi, H. Shibata, K. Mimura, M. Isshiki, Y. Waseda, Scripta Materialia 48, 431-435 (2003). DOI: https://doi.org/10.1016/S1359-6462(02)00441-4
• [13] S. Semboshi, S. Orimo, H. Suda, W. Gao, A. Sugawara, Mater. Transactions 52, 2137-2142 (2011). DOI: https://doi.org/10.2320/matertrans.M2011173
• [14] T. Hakkarainen. D. Tech thesis Formation of coherent Cu4Ti precipitates in copper-rich copper-titanium alloys: Dissertation, Helsinki University of Technology, Helsinky, Finland (1971).
• [15] D. Laughlin, J.V. Cahn, Acta Metallurgica 23, 329-339 (1975). DOI: https://doi.org/10.1016/0001-6160(75)90125-X
• [16] R.C. Ecob, J.V. Bee, B. Ralph, Metallurgical Transactions A 11, 1407-1414 (1980). DOI: https://doi.org/10.1007/BF02653496
• [17] J. Dutkiewicz, Metallurgical Transactions A 8, 751-761 (1977). DOI: https://doi.org/10.1007/BF02664785
• [18] M.J. Saarivirta, H.S. Cannon, Copper-titanium alloys, Metal. Progress. 76, 2 81-84 (1959).
• [19] S. Nagarjuna, K. Balusabramanian, D.S. Sarma, Mater. Transactions. 36, 1058-1066 (1995). DOI: https://doi.org/10.2320/matertrans1989.36.1058
• [20] Z. Boumerzoug, J. Mater. Eng. Tech. 003, 57-62 (2020).
• [21] M. Sundberg, R. Sundberg, S. Hogmark, R. Otterberg, B. Lehtinen, S. E. Hörnström, S.E. Karlsson, Wear 115, 151-165 (1987). DOI: https://doi.org/10.1016/0043-1648(87)90206-7
• [22] F. Zhou, Y. Wang, H. Ding, M. Wang, M. Yu, Z. Dai, Surface & Coating Tech. 202, 3808-3814 (2008). DOI: https://doi.org/10.1016/j.surfcoat.2008.01.025
• [23] P.S. Blau, Tribology International 34 (9), 585-591 (2001). DOI: https://doi.org/10.1016/S0301-679X(01)00050-0
• [24] F. Aydın, Y. Sun, Can, Metall. Quart. 57, 1-15 (2018). DOI: https://doi.org/10.1080/00084433.2018.1478491
• [25] G. Chassaing, L. Faure, S. Philippon, Wear 320, 25-33 (2014). DOI: https://doi.org/10.1016/j.wear.2014.08.001
• [26] J.F. Archard, Journal of Applied Physics 24 (8), 981-988 (1953). DOI: https://doi.org/10.1063/1.1721448

Uwagi

1. The authors disclosed receipt of the following financial support for the research, authorship, and/or publication of this article: The study was supported by Karabuk University Scientific Research Projects Unit (KBU-BAP) with Project No. KBU-BAP-17-DR-272

2. Opracowanie rekordu ze środków MEiN, umowa nr SONP/SP/546092/2022 w ramach programu "Społeczna odpowiedzialność nauki" - moduł: Popularyzacja nauki i promocja sportu (2022-2023).