The Influence of Technological Conditions of the Process of Cogging in Flat Dies on the Quality of Two-Phase Titanium Alloys

• Autorzy: Dyja H. , Tukibay A. A. , Mashekov S. A.

Identyfikatory

DOI

10.1515/amm-2016-0114

• Języki publikacji: EN

Abstrakty

EN

To create a rational technology of cogging process and to determinate the optimal values of the angles of tilt and single reduction the stress-strain state (SSS) of the blank during cogging in the flat dies was analyzed. By using the finite element method and program MSC.SuperForge quantitative data are obtained and the basic patterns of distribution of SSS, the temperature during the simulation of tilting in flat dies with different angles of tilting and the amount of reduction were established. Sustainable experimental-industrial technology of forging of two-phase titanium alloys was developed and tested.

Słowa kluczowe

EN

cogging; flat die; stress-strain state; effective stresses and strains; tilting; reduction

• Wydawca: Institute of Metallurgy and Materials Science of Polish Academy of Sciences ; Committee of Materials Engineering and Metallurgy of Polish Academy of Sciences
• Czasopismo: Archives of Metallurgy and Materials
• Rocznik: 2016
• Tom: Vol. 61, iss. 2A
• Strony: 671--676
• Opis fizyczny: Bibliogr. 12 poz., rys.

Twórcy

autor

Dyja H.

• Czestochowa University of Technology, Faculty of Production Engineering and Materials Technology, Institute of Metal Forming and Safety Engineering, 19 Armii Krajowej Av., 42-200 Częstochowa, Poland

autor

Tukibay A. A.

• Czestochowa University of Technology, Faculty of Production Engineering and Materials Technology, Institute of Metal Forming and Safety Engineering, 19 Armii Krajowej Av., 42-200 Częstochowa, Poland

autor

Mashekov S. A.

• Kazakh National Research Technical State University named after K.I. Satpayev, Almaty, Kazakhstan

Bibliografia

• [1] V. M. Chepkin, Opyt i problemy primeneniya titanovykh splavov v aviatsionnykh dvigatelyakh, Titan 1-2 (5-6), 13-15 (1995).
• [2] A. Gontarz, Z. Pater, K. Drozdowski, Forging on hammer of rim forging from titanium alloy Ti6Al4V, Archives of Metallurgy and Materials 57, 4, 1239-1246 (2012).
• [3] A. Świątoniowski, J. Sińczak, A. Łukaszek-Sołek, J. Schmidt, Analysis of forging process of the NiCrN superalloy for motor boat driving shaft, Archives of Metallurgy and Materials 57, 3, 719-725 (2012).
• [4] A. Kawałek, H. Dyja, S. Mróz, M. Knapiński, Effect of plate asymmetric rolling parameters on the change of the tptal unit pressure of roll. Metalurgija Metalurgy 50, 3 163-166 (2011).
• [5] Kovka i shtampovka /spravochnik v 4-kh tomakh/ Red sovet : Ye.I. Semenov i dr. -M.: Mashinostroyeniye 1, 568 (1985).
• [6] S. A. Mashekov, N.T. Biyakayeva A.S. Mashekova, Monografiya. Problemy kovki titanovykh splavov i ikh resheniya. Chast’ 1 i 2 Izdatel’stvo: LAP LAMBERT Academic Publishing 230, 251 (2013).
• [7] G. Banaszek, S. Berski, H. Dyja, A. Kawałek, Theoretical modelling of metallurgical defect closing-up processes during forming a forging. Journal of Iron and Steel Research International 20, 9 111-116 (2013).
• [8] Yu. M. Antoshchenkov, Raschet protsessov kovki. - M.: Mashinostroyeniye 240. 2001.
• [9] S. A. Mashekov, N.T. Biyakayeva, A.Ye. Nurtazayev, Tekhnologiya kovki v instrumente s izmenyayushcheysya formoy. - Izdatel’stvo LAP Lambert Academic Publishing 664, 2012.
• [10] YU .M.Antoshchenkov, Optimizatsiya tekhnologicheskikh parametrov kovki. - Kuznechno-shtampovochnoye proizvodstvo 12, 8-10 (2000).
• [11] K. M.Ivanov, V. S.Shevchenko, E. Ye.Yurgenson, Metod konechnykh elementov v tekhnologicheskikh zadachakh OMD: Uchebnoye posobiye. S-Pb: Institut Mashinostroyeniya 217, 2000.
• [12] V. A.Tyurin, Dopolnitel’nyye makrosdvigi pri plasticheskoy deformatsii slitkov, nepreryvnolitykh i prokatannykh zagotovok. - Metallurg 19, 33-35 (2000).