PL EN


Preferencje help
Widoczny [Schowaj] Abstrakt
Liczba wyników
Tytuł artykułu

Silicon nitride/carbon nanotube composites: preparation and characterization

Treść / Zawartość
Identyfikatory
Warianty tytułu
Języki publikacji
EN
Abstrakty
EN
This paper investigates the preparation of silicon nitride composites with multi-walled carbon nanotubes (MWCNTs). Samples containing 1–10 wt% MWCNTs were ultrasonically processed in non-aqueous suspensions, dried, pressed, and then subjected to non-pressure sintering at 1600 °C for 2 h. The preliminary results showed that the mixture of activated silicon nitride and covered MWCNTs could be sintered. The porosity of the obtained samples ranged from 0.27 to 36.94 vol.%. The microstructure was observed by scanning electron microscopy (SEM), and the mechanical properties (hardness and fracture toughness) were also determined. Good hardness values were obtained for samples prepared by sintering the mechanically activated precursor under a flowing nitrogen atmosphere using the lowest fraction of CNTs. Residual activator reduced the densification of the composites.
Rocznik
Strony
art. no. e138234
Opis fizyczny
Bibliogr. 17 poz., rys., tab.
Twórcy
  • Faculty of Materials Engineering, Department of Advanced Materials and Technologies, Silesian University of Technology, ul. Krasinskiego 8, 40-019 Katowice, Poland
Bibliografia
  • [1] M.S. Dresselhaus, G. Dresselhaus, and A. Jorio, “Unusual properties and structure of carbon nanotubes,” Ann. Rev. Mater. Res., vol. 34, pp. 247‒278, 2004, doi: 10.1146/annurev.matsci.34.040203.114607.
  • [2] S.V. Egorov et al., “Rapid microwave sintering of alumina ceramics with an addition of carbon nanotubes,” Ceram. Int., vol. 47, no. 4, pp. 4604‒4610, Feb. 2021, doi: 10.1016/j.ceramint.2020.10.027.
  • [3] I. Momohjimoh, M.A. Hussein, and N. Al-Aqeeli, “Recent Advances in the Processing and Properties of Alumina–CNT/SiC Nanocomposites,” Nanomaterials, vol. 9, no. 1, pp. 86, 2019, doi: 10.3390/nano9010086.
  • [4] E.T. Thostenson, Z. Ren, and T.W. Chou, “Advances in the science and technology of carbon nanotubes and their composites: a review,” Compos. Sci. Technol., vol. 61, pp. 1899‒1912, 2001, doi: 10.1016/S0266-3538(01)00094-X.
  • [5] A. Qadir, P. Pinke, and J. Dusza, “Silicon Nitride-Based Composites with the Addition of CNTs—A Review of Recent Progress, Challenges, and Future Prospects,” Materials, vol. 13, pp. 2799, 2020, doi: 10.3390/ma13122799.
  • [6] J. Wang, X. Deng, and S. Du, “Carbon Nanotube Reinforced Ceramic Composites: A Review”, Int. Ceram. Rev., vol. 63, pp. 286–289, 2014, doi: 10.1007/BF03401072.
  • [7] P. Manikandan, A. Elayaperumal, and R.F. Issac, “Influence of mechanical alloying process on structural, mechanical and tribological behaviours of CNT reinforced aluminium composites – a statistical analysis,” Bull. Pol. Acad. Sci. Tech. Sci., vol. 69, no. 2, p. e136745, 2021, doi: 10.24425/bpasts.2021.136745.
  • [8] K.J.D. MacKenzie and D.V. Barneveld, “Carbothermal synthesis of b-sialon from mechanochemically activated precursors,” J. Eur. Ceram. Soc., vol. 26, pp. 209‒215, 2006, doi: 10.1016/j.jeurceramsoc.2004.10.004.
  • [9] M. Sopicka-Lizer et al., “The effect of mechanical activation on the properties of -sialon precursors,” J. Eur. Ceram. Soc., vol.28, pp. 279‒288, 2008, doi: 10.1016/j.jeurceramsoc.2007.05.003.
  • [10] S. Walczak and M. Sibiński, “Flexible, textronic temperature sensors, based on carbon nanostructures”, Bull. Pol. Acad. Sci. Tech. Sci., vol. 62 no. 4, pp. 759‒763, 2014, doi: 10.2478/bpasts-2014-0082.
  • [11] X. Xu et al., “Fabrication of b-sialon nanoceramics by high-energy mechanical milling and spark plasma sintering,” Nanotechnology, vol. 16, no. 9, pp. 1569‒1573, 2005, doi: 10.1088/0957-4484/16/9/027.
  • [12] M. Sopicka-Lizer, M. Mikuśkiewicz (Tańcula), T. Pawlik, V. Kochnev, and E. Fokina, “The New Top-to-Bottom Method of SiAlON Precursor Preparation by Activation in a Planetary Mill With a High Acceleration,” Mater. Sci. Forum., vol. 554, pp. 59‒64, 2007, doi: 10.4028/www.scientific.net/MSF.554.59.
  • [13] M. Sopicka-Lizer, T. Pawlik, T. Włodek, M. Mikuśkiewicz (Tańcula), and G. Chernik, “The Effect of Sialon Precursor Nanostructurization in a Planetary Mill on the Properties of Sintered Ceramics,” Key Eng. Mater., vol. 352, pp. 179‒184, 2007, doi: 10.4028/www.scientific.net/KEM.352.179.
  • [14] M. Sopicka-Lizer, T. Pawlik, T. Włodek, and M. Mikuśkiewicz (Tańcula), “The phase evolution in the Si3N4-AlN system after high-energy mechanical treatment of the precursor powder,” Key Eng. Mater., vol. 403, pp. 7‒10, 2009, doi: 10.4028/www.scientific.net/KEM.403.7.
  • [15] Q. Liu, Q. Lu, G. Liu, and Q. Wei, “Preparation and property of β-SiAlON:Eu2+ luminescent fibers by an electrospinning method combined with carbothermal reduction nitridation,” J. Lumines., vol. 169, pp. 749‒754, 2016, doi: 10.1016/j.jlumin.2015.05.001.
  • [16] M. Biswas, S. Sarkar, and S. Bandyopadhyay, “Improvements in mechanical properties of SPS processed 15R-SiAlON polytype through structurally survived MWCNT reinforcement,” Mater. Chem. Phys. Mater. Chem. Phys., vol. 222, pp. 75‒80, 2019, doi: 10.1016/j.matchemphys.2018.09.084.
  • [17] V. Trovato, E. Teblum, Y. Kostikov, A. Pedrana, V. Re, G.D. Nessim, G. Rosace, “Electrically conductive cotton fabric coatings developed by silica sol-gel precursors doped with surfactant-aided dispersion of vertically aligned carbon nanotubes fillers in organic solvent-free aqueous solution,” J. Colloid Interface Sci., vol. 586, pp. 120‒134, 2021, doi: 10.1016/j.jcis.2020.10.076.
Typ dokumentu
Bibliografia
Identyfikator YADDA
bwmeta1.element.baztech-a09e61db-ca23-446e-bd46-29b1b0a01847
JavaScript jest wyłączony w Twojej przeglądarce internetowej. Włącz go, a następnie odśwież stronę, aby móc w pełni z niej korzystać.