Analysis of the Mechanical Properties of the Titanium Layer Obtained by the Mold Cavity Preparation Method

• Autorzy: Dulska A. , Szajnar J. , Król M.

Identyfikatory

DOI

10.24425/amm.2021.134758

• Języki publikacji: EN

Abstrakty

EN

The article presents the technology of layered casting with the use of 3D printing to make a frame insert. The insert was made of powdered titanium and then filled with liquid cast iron. The paper presents the results of research, including structure observation and hardness measurements, as well as abrasion resistance tests. The results indicate the possibility of creating a local reinforcement using a frame insert. The resulting casting is characterized by a local increase in hardness and, in addition, an increase in abrasion resistance of the entire surface layer. The quality of the obtained connection depends strongly on the casting parameters.

Słowa kluczowe

EN

modular insert; titanium layer; cast iron; SLM

• Wydawca: Institute of Metallurgy and Materials Science of Polish Academy of Sciences ; Committee of Materials Engineering and Metallurgy of Polish Academy of Sciences
• Czasopismo: Archives of Metallurgy and Materials
• Rocznik: 2021
• Tom: Vol. 66, iss. 1
• Strony: 51--56
• Opis fizyczny: Bibliogr. 26 poz., fot., rys., tab.

Twórcy

autor

Dulska A.

• Silesian University of Technology, Department of Foundry Engineering, Towarowa 7 St, 44-100 Gliwice, Poland

autor

Szajnar J.

• Silesian University of Technology, Department of Foundry Engineering, Towarowa 7 St, 44-100 Gliwice, Poland

autor

Król M.

• Silesian University of Technology, Department of Engineering Materials and Biomaterials, 18A Konarskiego Str., 44-100 Gliwice, Poland

Bibliografia

• [1] Z. Górny, Solidification of Metals and Alloys 11, 135-164 (1987).
• [2] X. Zhi, Y. Han, J. Liu, M. Zhao, S. Ma, Int. J. Mater. Res.105 (10), 953-960 (2014).
• [3] M. Ingaldi, A. Czajkowska, 2nd International Conference on the Sustainable Energy and Environmental Development, IOP Conf. Series: Earth and Environmental Science 214, 1-8 012003 (2019). DOI:10.1088/1755-1315/214/1/012003
• [4] S. Žic, I. Džambas, M. Konić, Metalurgija 48 (1), 51-54 (2009).
• [5] R. Zhou, Y. Jiang, D. Lu, Wear 255, 134-138 (2003). DOI.org/10.1016/S0043-1648(03)00290-4.
• [6] B.A. Moreira, R.O. Sousa, P. Lacerda, L.M.M. Ribeiro, A.M.P. Pinto, M.F. Vieira, Materials, 13, 209, 1-14 (2020). DOI:10.3390/ma13010209.
• [7] E. Olejnik, Ł. Szymański, P. Kurtyka, T. Tokarski, B. Grabowska, P. Czapla, Arch. Foundry Eng. 16 (2), 89-94 (2016). https://doi.org/10.1515/afe-2016-0032.
• [8] A. Dulska, 12th International Conference Quality Production Improvement - QPI 2018, Zaborze near Myszków, Poland, June 18-20, 2018. MATEC Web of Conferences. MATEC Web of Conferences 183, 02005, 1-6 (2018). DOI: https://doi.org/10.1051/matecconf/201818302005.
• [9] N. Przyszlak, A. Dulska, T. Wróbel, J. Szajnar, Archives of Foundry Engineering 18 (1), 99-102 (2018). DOI: 10.24425/118819.
• [10] T. Wróbel, J. Mater. Eng. Perform. 23 (5), 1711-1717 (2014). https://doi.org/10.1007/s11665-014-0953-4.
• [11] R. Dojka, J. Jezierski, N.S. Tiedje, J. Mater. Eng. Perform. 28, 7, 3922-3928 (2019). DOI 10.1007/s11665-019-03973-9.
• [12] S. Negi, S. Dhiman, R.K. Sharma, Rapid Prototyping J. 20 (3), 256-267 (2014).
• [13] P. Nuckowski, P. Snopiński, T. Wróbel, Materials 13, 3, 576, 1-14 (2020). DOI:10.3390/ma13030576.
• [14] A.B. Spierings, N. Herres, G. Levy, Rapid Prototyping J. 17 (3), 195-202 (2011).
• [15] I. Cambell, D. Bourell, I. Gibson, Rapid Prototyping Journal 19, 353-364 (2012).
• [16] A. Szafrańska, A. Antolak-Dudka, P. Baranowski, P. Bogusz, D. Zasada, J. Małachowski, T. Czujko, Materials 12, 886, 1-19 (2019). DOI:10.3390/ma12060886.
• [17] J. Yu, M. Rombouts, G. Maes, F. Motmans. Physics Proc. 39, 416-424 (2012).
• [18] M. Dojka, R. Dojka, M. Stawarz, A. Studnicki, J. Mater. Eng. Perform. 28, 7, 4002-4011
• [19] M. Stawarz, M. Dojka, K. Janerka, 25th Anniversary International Conference on Metallurgy and Materials, Brno, Czech Republic, May 25th-27th, Conference Proceedings 229-233 (2016).
• [20] S. Sobula, E. Olejnik, T. Tokarski, Arch. Foundry Eng. 17 (1), 143-146 (2017). DOI: 10.1515/afe-2017-0026.
• [21] B.-X. Dong, F. Qiu, Q. Li, S.-L. Shu, H.-Y. Yang, Qi.-Ch. Jiang, Nanomaterials 9, 1152, 1-40 (2019). DOI: 10.3390/nano9081152.
• [22] W. Lengauer, Encyclopedia of Inorganic and Bioinorganic Chemistry, Chapter December 2012 (2012). DOI: 10.1002/9781119951438.eibc0032.pub2.
• [23] Xiaowei Yin, I. Gotman, L. Klinger, E.Y. Gutmanas, Mater. Sci. Eng. A. 396, 107-114 (2005). DOI:10.1016/j.msea.20085.01.011.
• [24] A. Walasek, Designing of the structure and properties of the alloyed surface layer on the cast steel castings. Unpublished doctoral dissertation Silesian University of Technology, Poland (2012), in Polish.
• [25] A. Wassilikowska, A. Czaplicka-Kotas, M. Zielina, A. Bielski, Technical Transactions Chemistry 18 (1), 133-148 (2014).
• [26] T. Wróbel, Layered castings made by method of mould cavity preparation with monolithic insert, Archives of Foundry Engineering, Katowice - Gliwice (2016), in Polish.

Uwagi

Opracowanie rekordu ze środków MNiSW, umowa Nr 461252 w ramach programu "Społeczna odpowiedzialność nauki" - moduł: Popularyzacja nauki i promocja sportu (2021).