Refinement of the Manufacturing Route and Evaluation of the Reinforcement Effect of MAX Phases in Al Alloy Matrix Composite Materials

• Autorzy: Dmitruk Anna , Naplocha Krzysztof , Żak Andrzej , Strojny-Nędza Agata

Identyfikatory

DOI

10.24425/afe.2024.149262

• Języki publikacji: EN

Abstrakty

EN

Microwave Assisted Self-propagating High-temperature Synthesis (MASHS) was used to prepare open-porous MAX phase preforms in Ti-Al-C and Ti-Si-C systems, which were further used as reinforcements for Al-Si matrix composite materials. The pretreatment of substrates was investigated to obtain open-porous cellular structures. Squeeze casting infiltration was chosen to be implemented as a method of composites manufacturing. Process parameters were adjusted in order to avoid oxidation during infiltration and to ensure the proper filling. Obtained materials were reproducible, well saturated and dense, without significant residual porosity or undesired interactions between the constituents. Based on this and the previous work of the authors, the reinforcement effect was characterized and compared for both systems. For the Al-Si+Ti-Al-C composite, an approx. 4-fold increase in hardness and instrumental Young's modulus was observed in relation to the matrix material. Compared to the matrix, Al-Si+Ti-Si-C composite improved more than 5-fold in hardness and almost 6-fold in Young's modulus. Wear resistance (established for different loads: 0.1, 0.2 and 0.5 MPa) for Al-Si+Ti-Al-C was two times higher than for the sole matrix, while for Al-Si+Ti-Si-C the improvement was up to 32%. Both composite materials exhibited approximately two times lower thermal expansion coefficients than the matrix, resulting in enhanced dimensional stability.

Słowa kluczowe

EN

MAX Phase; composite; squeeze casting; SHS synthesis; pressure infiltration

PL

MAX Phase; kompozyt; odlewanie metodą prasowania; synteza SHS; infiltracja ciśnieniowa

• Wydawca: Komisja Odlewnictwa Polskiej Akademii Nauk Oddział w Katowicach
• Czasopismo: Archives of Foundry Engineering
• Rocznik: 2024
• Tom: Vol. 24, iss. 1
• Strony: 141--148
• Opis fizyczny: Bibliogr. 44 poz., il., tab., wykr.

Twórcy

autor

Dmitruk Anna

• Wrocław University of Science and Technology, Faculty of Mechanical Engineering, Poland

• https://orcid.org/0000-0002-8450-2088

autor

Naplocha Krzysztof

• Wrocław University of Science and Technology, Faculty of Mechanical Engineering, Poland

• https://orcid.org/0000-0003-0667-6645

autor

Żak Andrzej

• Wrocław University of Science and Technology, Faculty of Chemistry, Institute of Advanced Materials, Poland

• https://orcid.org/0000-0002-4512-2816

autor

Strojny-Nędza Agata

• Łukasiewicz Institute of Microelectronics and Photonics, Poland

• https://orcid.org/0000-0002-5946-3662

Bibliografia

• [1] Gonzalez-Julian, J. (2021). Processing of MAX phases: From synthesis to applications. Journal of the American Ceramic Society. 104, 659-690. https://doi.org/10.1111/jace.17544.
• [2] Barsoum, M.W. (2013). MAX Phases: Properties of Machinable Ternary Carbides and Nitrides. Wiley-VCH.
• [3] Arróyave, R., Talapatra, A., Duong, T., Son, W., Gao, H. & Radovic M. (2017). Does aluminum play well with others? Intrinsic Al-A alloying behavior in 211/312 MAX phases. Materials Research Letters. 5(3), 170-178. https://doi.org/10.1080/21663831.2016.1241319.
• [4] Khoptiar, Y. & Gotman, I. (2002). Ti2AlC ternary carbide synthesized by thermal explosion, Materials Letters. 57(1), 72-76. https://doi.org/10.1016/S0167-577X(02)00701-2.
• [5] Jeitschko, W. & Nowotny, H. (1967). Die kristallstruktur von Ti3SiC2-ein neuer komplexcarbid-typ. Monatshefte Für Chemie. 98, 329-337. https://doi.org/10.1007/BF00899949.
• [6] El Saeed, M.A., Deorsola, F.A. & Rashad, R.M. (2013). Influence of SPS parameters on the density and mechanical properties of sintered Ti3SiC2 powders. International Journal of Refractory Metals and Hard Materials. 41, 48-53. https://doi.org/10.1016/j.ijrmhm.2013.01.016.
• [7] Radhakrishnan, R., Williams, J.J. & Akinc M. (1999). Synthesis and high-temperature stability of Ti3SiC2. Journal of Alloys and Compounds. 285(1-2), 85-88. https://doi.org/10.1016/S0925-8388(99)00003-1.
• [8] Wang, Y., Huang, Z., Hu, W., Cai, L., Lei, C., Yu, Q. & Jiao Y. (2021). Preparation and characteristics of Ti3AlC2-Al3Ti/Al composite materials synthesized from pure Al and Ti3AlC2 powders. Materials Characterization. 178, 111298. https://doi.org/10.1016/j.matchar.2021.111298.
• [9] Wang, Z., Ma, Y., Sun, K., Zhang, Q., Zhou, C., Shao, P., Xiu, Z. & Wu, G. (2022). Enhanced ductility of Ti3AlC2 particles reinforced pure aluminum composites by interface control. Materials Science and Engineering: A. 832, 142393. https://doi.org/10.1016/j.msea.2021.142393.
• [10] Zhai, W., Pu, B., Sun, L., Xu, L., Wang, Y., He, L., Dong, H., Gao, Y., Han, M. & Xue, Y. (2022). Influence of Ti3AlC2 content and load on the tribological behaviors of Ti3AlC2p/Al composites. Ceramics International. 48(2), 1745-1756. https://doi.org/10.1016/j.ceramint.2021.09.254.
• [11] Anasori, B., Caspi, E.N. & Barsoum, M.W. (2014). Fabrication and mechanical properties of pressureless melt infiltrated magnesium alloy composites reinforced with TiC and Ti2AlC particles. Materials Science and Engineering: A. 618, 511-522. https://doi.org/10.1016/j.msea.2014.09.039.
• [12] Anasori, B. & Barsoum, M.W. (2016). Energy damping in magnesium alloy composites reinforced with TiC or Ti2AlC particles. Materials Science and Engineering: A. 653, 53-62. https://doi.org/10.1016/j.msea.2015.11.070.
• [13] Hu, L., Kothalkar, A., O’Neil, M., Karaman, I. & Radovic, M. (2014). Current-activated, pressure-assisted infiltration: A novel, versatile route for producing interpenetrating ceramic-metal composites. Materials Research Letters. 2, 124-130. https://doi.org/10.1080/21663831.2013.873498.
• [14] Song, I.H., Kim, D.K., Hahn, Y.D. & Kim, H.D. (2004). Investigation of Ti3AlC2 in the in situ TiC-Al composite prepared by the exothermic reaction process in liquid aluminum. Materials Letters. 58(5), 593-597. https://doi.org/10.1016/S0167-577X(03)00576-7.
• [15] Wang, W.J., Gauthier-Brunet, V., Bei, G.P., Laplanche, G., Bonneville, J., Joulain, A. & Dubois, S. (2011). Powder metallurgy processing and compressive properties of Ti3AlC2/Al composites. Materials Science and Engineering: A. 530, 168-173. https://doi.org/10.1016/j.msea.2011.09.068.
• [16] Chen, Y.L., Yan, M., Sun, Y.M., Mei, B.C. & Zhu, J.Q. (2009). The phase transformation and microstructure of TiAl/Ti2AlC composites caused by hot pressing. Ceramics International. 35(5), 1807-1812. https://doi.org/10.1016/j.ceramint.2008.10.009.
• [17] Fedotov. A.F., Amosov. A.P., Latukhin. E.I. & Novikov. V.A. (2016). Fabrication of aluminum–ceramic skeleton composites based on the Ti2AlC MAX phase by SHS compaction. Russian Journal of Non-Ferrous Metals. 57(5), 33-40. https://doi.org/10.3103/S1067821216010053.
• [18] Dang, W., Ren, S., Zhou, J., Yu, Y., Li, Z. & Wang, L. (2016). Influence of Cu on the mechanical and tribological properties of Ti3SiC2. Ceramics International. 42(8), 9972-9980. https://doi.org/10.1016/j.ceramint.2016.03.099.
• [19] Shi, X., Wang, M., Xu, Z., Zhai, W. & Zhang, Q. (2013). Tribological behavior of Ti3SiC2/(WC-10Co) composites prepared by spark plasma sintering. Materials & Design. 45, 365-376. https://doi.org/10.1016/j.matdes.2012.08.069.
• [20] Dang, W., Ren, S., Zhou, J., Yu, Y. & Wang, L. (2016). The tribological properties of Ti3SiC2/Cu/Al/SiC composite at elevated temperatures. Tribology International. 104, 294-302. https://doi.org/10.1016/j.triboint.2016.09.008.
• [21] Krinitcyn, M., Fu, Z., Harris, J., Kostikov, K., Pribytkov, G.A., Greil, P. & Travitzky, N. (2017). Laminated object manufacturing of in-situ synthesized MAX-phase composites. Ceramics International. 43(12), 9241-9245. https://doi.org/10.1016/j.ceramint.2017.04.079.
• [22] Li, H., Peng, L.M., Gong, M., He, L.H., Zhao, J.H. & Zhang, Y.F. (2005). Processing and microstructure of Ti3SiC2 / M (M = Ni or Co) composites. Materials Letters. 59(21), 2647-2649. https://doi.org/10.1016/j.matlet.2005.04.010.
• [23] Sun, Z., Zhou, M.C. & Li, S. (2002). Tribological behavior of Ti3SiC2 based materials. Journal of Materials Science & Technology. 18(2), 142-145.
• [24] Hu, C., Zhou, Y., Bao, Y. & Wan, D. (2006). Tribological properties of polycrystalline Ti3SiC2 and Al2O3-reinforced Ti3SiC2 composites. Journal of the American Ceramic Society. 89(11), 3456-3461. https://doi.org/10.1111/j.1551-2916.2006.01253.x.
• [25] Yang, J., Gu, W., Pan, L.M., Song, K., Chen, X. & Qiu, T. (2011). Friction and wear properties of in situ (TiB2+TiC)/Ti3SiC2 composites. Wear. 271(11-12), 2940-2946. https://doi.org/10.1016/j.wear.2011.06.017.
• [26] Lis, J., Chlubny, L., Łopaciński, M., Stobierski, L. & Bućko, M.M. (2008). Ceramic nanolaminates-Processing and application. Journal of the European Ceramic Society. 28(5), 1009-1014. https://doi.org/10.1016/j.jeurceramsoc.2007.09.033.
• [27] Naplocha, K. (2013). Composite materials strengthened with preforms produced in the process of high-temperature synthesis in a microwave field (in Polish: Materiały kompozytowe umacniane preformami wytworzonymi w procesie wysokotemperaturowej syntezy w polu mikrofalowym). Wroclaw: Oficyna Wydawnicza PWr.
• [28] Merzhanov, G. (2011). Thermally coupled SHS reactions. International Journal of Self-Propagating High-Temperature Synthesis. 20, 61-63. https://doi.org/10.3103/ S1061386211010109.
• [29] Dmitruk, A., Żak, A., Naplocha, K., Dudziński, W. & Morgiel, J. (2018). Development of pore-free Ti-Al-C MAX/Al-Si MMC composite materials manufactured by squeeze casting infiltration. Materials Characterization. 146, 182-188. https://doi.org/10.1016/j.matchar.2018.10.005.
• [30] Dmitruk, A., Naplocha, K., Żak, A., Strojny-Nędza, A., Dieringa, H. & Kainer K.U. (2019). Development of pore-free Ti-Si-C MAX/Al-Si composite materials manufactured by squeeze casting infiltration. Journal of Materials Engineering and Performance. 28, 6248-6257. https://doi.org/10.1007/s11665-019-04390-8.
• [31] Dmitruk, A., Naplocha, K. & Strojny-Nędza, A. (2018). Thermal properties of Al alloy matrix composites reinforced with MAX type phases. Composites Theory and Practice. 18(1), 32-36.
• [32] Dmitruk, A. & Naplocha, K. (2018). Manufacturing of Al alloy matrix composite materials reinforced with MAX phases. Archives of Foundry Engineering. 18(2), 198-202. DOI: 10.24425/122528.
• [33] Chen X. & Bei G. (2017). Toughening mechanisms in nanolayered MAX phase ceramics-a review. Materials (Basel). 10(4), 1-12. https://doi.org/10.3390/ma10040366.
• [34] Yang, J., Liao, C., Wang, J., Jiang, Y. & He, Y. (2014). Effects of the Al content on pore structures of porous Ti3 AlC2 ceramics by reactive synthesis. Ceramics International. 40(3), 4643-4648. https://doi.org/10.1016/ j.ceramint.2013.09.004.
• [35] Hashimoto, S., Nishina, N., Hirao, K., Zhou, Y., Hyuga, H., Honda, S. & Iwamoto, Y. (2012). Formation mechanism of Ti2AlC under the self-progating high-temperature synthesis (SHS) mode. Materials Research Bulletin. 47(5), 1162-1168. https://doi.org/10.1016/j.materresbull.2012.02.003.
• [36] Yang. J., Liao. C., Wang. J., Jiang. Y. & He. Y. (2014). Reactive synthesis for porous Ti3AlC2 ceramics through TiH2, Al and graphite powders. Ceramics International. 40(5), 6739-6745. https://doi.org/10.1016/ j.ceramint.2013.11.136.
• [37] Hendaoui, A., Vrel, D., Amara, A., Langlois, P., Andasmas, M. & Guerioune, M. (2010). Synthesis of high-purity polycrystalline MAX phases in Ti-Al-C system through mechanically activated self-propagating high-temperature synthesis. Journal of the European Ceramic Society. 30(4), 1049-1057. https://doi.org/10.1016/j.jeurceramsoc.2009.10.001.
• [38] Yeh, C.L. & Shen, Y.G. (2008). Effects of SiC addition on formation of Ti3SiC2 by self-propagating high-temperature synthesis. Journal of Alloys and Compounds. 461(1-2), 654-660. https://doi.org/10.1016/j.jallcom.2007.07.088.
• [39] Zhang, Y., Ding, G.P., Zhou, Y.C. & Cai, B.C. (2002). Ti3SiC2 - a selflubricating ceramic, Materials Letters. 55(5), 285-289. https://doi.org/10.1016/S0167-577X(02)00379-8.
• [40] Radovic, M. & Barsoum, M.W. (2013). MAX phases: Bridging the gap between metals and ceramics. American Ceramic Society Bulletin. 92(3), 20-27.
• [41] Barsoum, M.W., El-raghy, T., Rawn, C.J., Porter, W.D., Wang, H., Payzant, E.A. & Hubbard, C.R. (1999). Thermal properties of Ti3SiC2. Journal of Physics and Chemistry of Solids. 60(4), 429-439. https://doi.org/10.1016/S0022-3697(98)00313-8.
• [42] Son, W., Duong, T., Talapatra, A., Gao, H., Arróyave, R. & Radovic, M. (2016). Ab-initio investigation of the finite-temperatures structural, elastic, and thermodynamic properties of Ti3AlC2 and Ti3SiC2. Computational Materials Science. 124, 420-427. https://doi.org/10.1016/j.commatsci.2016.08.015.
• [43] Shih, C., Meisner, R., Porter, W., Katoh, Y. & Zinkle, S.J. (2013). Physical and thermal mechanical characterization of non-irradiated MAX phase materials (Ti-Si-C and Ti-Al-C systems). Fusion Reactor Materials Program. 55, 78-93.
• [44] Wang, X.H. & Zhou, Y.C. (2010). Layered Machinable and electrically conductive Ti2AlC and Ti3AlC2 ceramics: a review. Journal of Materials Science & Technology. 26(5), 385-416. https://doi.org/10.1016/S1005-0302(10)60064-3.

Uwagi

Opracowanie rekordu ze środków MNiSW, umowa nr SONP/SP/546092/2022 w ramach programu "Społeczna odpowiedzialność nauki" - moduł: Popularyzacja nauki i promocja sportu (2024)