Effect of burnishing on the corrosion properties of Ni-5%Al AND Ni-5%Al-15%Al2O3 coatings obtained by plasma spraying

• Autorzy: Starosta R.

Identyfikatory

DOI

10.5604/12314005.1134113

• Języki publikacji: EN

Abstrakty

EN

The Ni-5%Al alloy coatings and Ni-5% Al-15%Al2O3 composite coatings were obtained by plasma spraying method. The PN120 gun was used. The coatings onto a shaft made of austenitic stainless steel (X5CrNi 18-10) were sprayed. The coatings were subjected to turning, burnishing. The evaluation of corrosion properties were based on the measurements of corrosion current density and corrosion potential (polarization method), the charge transfer resistance and exponent of constant phase element impedance (electrochemical impedance spectroscopy method). Corrosion tests were performed in replacement seawater (3.5% sodium chloride solution). On the basis of studies, the effect of finishing type on the corrosion properties of plasma sprayed coatings has been demonstrated. The lowest corrosion current density was found for Ni-5% Al coatings after burnishing, icorr value equal to 0.96 A/cm2, and the charge transfer resistance was 27007 Ωcm2. The lowest resistance to corrosion of turned Ni-5%Al-15%Al2O3 composite coatings was observed. These coatings were characterized by the following parameters of corrosion process: icorr = 17.64 A/cm2, Rct = 2137 Ωcm2. Burnishing caused increased corrosion resistance of coatings. Due to reduced roughness and waviness are obtained reduction of the area of the actual burnished coatings compared to turned coatings. Thus, it is resulting in reduced values of corrosion current density. After finishing treatment, the plasma sprayed Ni-5%Al-15%Al2O3 coatings characterized by lower corrosion resistance compared to the alloy coating. The presence of the reinforcing phase in the coating promotes the increase of the porosity. The plasma sprayed coatings on nickel matrix had a tendency to localized corrosion in sodium chloride solution.

Słowa kluczowe

EN

plasma spraying; composite coating; Ni-Al; burnishing; corrosion; polarization test; EIS test

• Wydawca: Łukasiewicz Research Network - Institute of Aviation ; European Science Society of Powertrain and Transport KONES Poland ; Wydawnictwo Instytutu Technicznego Wojsk Lotniczych
• Czasopismo: Journal of KONES
• Rocznik: 2014
• Tom: Vol. 21, No. 1
• Strony: 273--280
• Opis fizyczny: Bibliogr. 15 poz., rys.

Twórcy

autor

Starosta R.

• Gdynia Maritime University, Department of Marine Maintenance Morska Street 81-87, 81-225 Gdynia, Poland tel.:[phone], fax: [phone]

Bibliografia

• [1] Axir, M. H., An investigation into roller burnishing, International Journal of Machine Tools and Manufacture, Vol. 40, pp. 1603-1617, 2000.
• [2] Bradai, M. A., Sadeddine, A., Microstructural and Mechanical Properties of Ni-Base Thermal Spray Coatings Deposited by Flame Spraying, Metal. and Mater. Tran., Vol. 42B, pp. 932-937, 2011.
• [3] Dyl, T., Starosta, R., Effect of the ceramic dispersion in the nickiel matrix composite coatings on corrosion properties after plastic working. Solid State Phenomena, Vol. 183, pp. 43-48, 2012.
• [4] Łabanowski, J., Ossowska, A., Wpływ nagniatania na właściwości stali austentycznoferrytycznych typu duplex, Wspołczesne problemy w technologii obrobki przez nagniatanie, praca zbiorowa pod red. W. Przybylskiego, Wyd. Politechniki Gdańskiej, Vol. 2, Gdansk 2008.
• [5] Mhaede, M., Influence of surface treatments on surface layer properties, fatigue and corrosion fatigue performance of AA7075 T73, Materials and Design, Vol. 41, pp. 61-66, 2012.
• [6] Mindivan, H., A study on wear and corrosion behaviour of thermally sprayed alumina-titania composite coatings on aluminium alloys, Kovove Materialy, Vol. 48, pp. 203-210, 2010.
• [7] Picas, J. A., Forn, A., Matthaus, G., HVOF coatings as an alternative to hard chrome for pistons and valves, Wear, Vol. 261, pp. 477-484, 2006.
• [8] Prevey, P. S., Cammett, J., Low cost corrosion damage mitigation and improved fatigue performance of low plasticity burnished 7075-T6, Journal of Materials Engineering and Performance, Vol. 10, pp. 548-55, 2001.
• [9] Przybylski, W., Zastosowanie obrobki nagniataniem w technologii siłownikow hydraulicznych, Postępy Nauki i Techniki, Vol. 6, pp. 196-201, 2011.
• [10] Przybylski, W., Wiśniewska, A., Zastosowanie nagniatania w obrobce wykończeniowej części maszyn, Wspołczesne problemy w technologii obrobki przez nagniatanie, praca zbiorowa pod red. W. Przybylskiego, Wyd. Politechniki Gdańskiej, Vol. 2, Gdańsk 2008.
• [11] Pu, Z., Song, G. L., Yang, S., Outeiro, J. C., Dillon Jr, O. W., Puleo, D. A., Jawahir, I. S., Grain refined and basal textured surface produced by burnishing for improved corrosion performance of AZ31B Mg alloy, Corrosion Science, Vol. 57, pp. 192-201, 2012.
• [12] Pu, Z., Yang, S., Song, G. L., Dillon Jr, O. W., Puleo, D. A., Jawahir I.S., Ultrafinegrained surface layer on Mg-Al-Zn alloy produced by cryogenic burnishing for enhanced corrosion resistance, Scripta Materialia, Vol. 65, pp. 520-523, 2011.
• [13] Starosta, R., Corrosion of Ni-Al and Ni-Al-Al2O3 plasma sprayed coatings in 0.01 M H2SO4 and 3.5% NaCl solutions, Solid State Phenomena, Vol. 199, pp. 390-395, 2013.
• [14] Starosta, R,. Effect of burnishing on surface texture of Ni-Al plasma sprayed coatings, Journal of KONES Powertrain and Transport, Vol. 19, pp. 377-384, 2012.
• [15] Starosta, R., Podstawy wytwarzania i obrobki powłok kompozytowych w procesach regeneracji elementow maszyn i urządzeń eksploatowanych w środowisku wody morskiej, Akademia Morska, Gdynia 2013.