Non traditional cooling technique using Peltier effect for single point boron carbide (B4C) cutting tool doping with titanium carbide (TiC)

• Autorzy: Sreenivasulu Reddy , Valeti Krishna Teja

Identyfikatory

DOI

10.30464/jmee.2021.5.1.31

• Języki publikacji: EN

Abstrakty

EN

A single point cutting tool is modeled out of two different materials having desired thermoelectric properties. The tool material used is Boron Carbide (B4C) doped with different compositions of Titanium Carbide (TiC). In the present work, three different compositions of Titanium Carbide doped on both sides of cutting tool made by Boron carbide. The available combinations of Titanium Carbide (TiC) from the work bench in ANSYS was selected with three cases of 0 & 25.4%, 0% &12.5% and 12.5% & 25.4% on first half and second half of the cutting tool respectively. The simulation process is done in ANSYS 2020 R2 software, thermal-electric module (TEM) is used. From these studies it is evident that considerable cooling effect is achieved and found to be the lowest temperature of 10.93°C is observed for the combination of 0% &25.4%, 18.79°C is observed for the combination of 0& 12.5% and 26.73°C for 12.5% and 25.4% combination at the junction of the tool material which is nearer to the cutting tip respectively. Finally it is concluded that one side of cutting tool without any doping and other side with 25.4% TiC doped showed good results which observed by conducting number of simulations at different levels of iterations for Titanium Carbide doped Boron Carbide cutting tool used in turning operation.

Słowa kluczowe

EN

Peltier cooling effect; thermoelectric module; ANSYS 2020 R2; titanium carbide; solidworks 2020; boron carbide cutting tool

PL

efekt Peltiera; chłodzenie; moduł termoelektryczny; ANSYS; węglik tytanu; SolidWorks; węglik boru; narzędzia skrawające

• Wydawca: Wydawnictwo Uczelniane Politechniki Koszalińskiej
• Czasopismo: Journal of Mechanical and Energy Engineering
• Rocznik: 2021
• Tom: Vol. 5, No 1
• Strony: 31--38
• Opis fizyczny: Bibliogr. 12 poz., rys., tab., wykr.

Twórcy

autor

Sreenivasulu Reddy

• R.V.R&J.C.College of Engineering (Autonomous), Department of Mechanical Engineering, Guntur, Andhra Pradesh, INDIA - 522019

• https://orcid.org/0000-0002-7442-7141

autor

Valeti Krishna Teja

• R.V.R&J.C.College of Engineering (Autonomous), Department of Mechanical Engineering, Guntur, Andhra Pradesh, INDIA - 522019

Bibliografia

• 1. Murarka, P.D., Hinduja, S. and Barrow, G. (1981). Influence of strain, strain-rate and temperature on the flow stress in the primary deformation zone in metal cutting. International Journal of Machine Tool Design and Research, Vol 21 (3-4), pp. 207-216.
• 2. Sreejith, P.S. and Ngoi, B.K.A. (2000). Dry machining: machining of the future. Journal of materials processing technology, Vol 101 (1-3), pp. 287-291.
• 3. O’Sullivan, D. and Cotterell, M. (2001) Temperature measurement in single point turning. Journal of materials processing technology, Vol 118 (1-3), pp. 301-308.
• 4. Abukhshim, N.A., Mativenga, P.T. and Sheikh, M.A. (2006). Heat generation and temperature prediction in metal cutting: A review and implications for high speed machining. International Journal of Machine Tools and Manufacture, Vol 46 (7-8), pp. 782-800.
• 5. Patwari, M.A.U, Habib, M.A., Ehsan, M.T., Ahnaf, M.G. & Chowdhury M.S. (2017). An innovative green cooling approach using peltier chip in milling operation for surface roughness improvement. International Journal of Industrial and Manufacturing Engineering, Vol 11(7), pp. 1303-1307.
• 6. Byrne, G. (1987). Thermoelectric signal characteristics and average interfacial temperatures in the machining of metals under geometrically defined conditions, International Journal of Machine Tools and Manufacture, Vol 27 (2), pp. 215-224.
• 7. Nan, C.W, Paderno, Y. & McLachlan D.S. (2000) Effect of titanium carbide addition on the thermo electric properties of boron carbide ceramics, Solid state communications, Vol. 115, Issue10, pp. 523-526.
• 8. Chakraborty P., Ma, T., Zahiri A.H., Cao, L. & Wang, Y. (2018) Carbon based materials for thermoelectrics. Advances in Condensed Matter Physics, Article ID 3898479, 29 pages.
• 9. Darukhanavala, J.P. (1965) Thermoelectric cooling of a lathe cutting tool, Master’s thesis, Department of industrial Engineering, Kansas State University, Manhattan, Kansas, pp 48-52.
• 10. Stephenson, D.A. and Agapiou, J.S.(2016). Metal cutting theory and practice, pp 29-31, CRC press.
• 11. Sreenivasulu, R., & SrinivasaRao, C. (2018). Modelling, Simulation and Experimental validation of Burr size in Drilling of Aluminium 6061 alloy. Procedia Manufacturing, Vol. 20, pp 458-463.
• 12. Sreenivasulu, Reddy, and C. Srinivasa Rao. (2013) Modeling and optimization of thrust force and torque during drilling of aluminum 6061 alloy using taguchi–grey analysis approach. Int J Adv Mat Manuf Characterization, Vol. 3, pp 413-418.

Uwagi

PL

Opracowanie rekordu ze środków MNiSW, umowa Nr 461252 w ramach programu "Społeczna odpowiedzialność nauki" - moduł: Popularyzacja nauki i promocja sportu (2021).