Microstructure of sintered Cu/SiC composites

• Autorzy: Gwoździk M. , Bałaga Z.

Warianty tytułu

PL

Mikrostruktura spiekanych kompozytów Cu/SiC

• Języki publikacji: EN

Abstrakty

EN

The paper presents the preliminary results of studies on obtaining copper-based composite materials strengthened with silicon carbides. Electrolytically obtained copper powders were used as the matrix. The sinters were characterized by different SiC contents (0, 5, 10, 15 wt.%). The materials were consolidated by one-sided pressing followed by sintering (T = 800°C, t = 1 h). One-sided pressing was carried out at the pre-set pressing pressure of 60 kN and at the rate of 200 N/s. The research was performed on powders, mouldings and sinters. Investigations of the composites comprised: microscopic examinations (SEM), chemical composition analysis (SEM), XRD measurements, the density of the composites was determined, and a quantitative evaluation of the porosity of the composites was carried out.

PL

Przedstawiono wyniki badań otrzymywania materiałów kompozytowych na osnowie miedzi umacnianych węglikiem krzemu. Osnowę kompozytów stanowiły proszki miedzi otrzymane metodą elektrolityczną. Spieki charakteryzowały sie różną zawartością SiC (0, 5, 10, 15% wag. SiC). Konsolidacja materiałów następowała poprzez jednostronne prasowanie i następujące po nim spiekanie (T = 800°C, t = 1 h). Prasowanie odbywało się przy założonym nacisku prasowania 60 kN i szybkości 200 N/s. Badania przeprowadzone zostały na proszkach, wypraskach oraz spiekach. Badania obejmowały: badania mikroskopowe (SEM), analizę składu chemicznego (SEM), pomiary rentgenowskie (XRD), określenie gęstości kompozytów, wykonanie ilościowej analizy porowatości w materiałach kompozytowych.

Słowa kluczowe

EN

sinters Cu/SiC; porosity; SEM; XRD

PL

laminaty spieki Cu/SiC; porowatość; SEM; XRD

• Wydawca: Polskie Towarzystwo Materiałów Kompozytowych
• Czasopismo: Composites Theory and Practice
• Rocznik: 2018
• Tom: R. 18, nr 2
• Strony: 95--102
• Opis fizyczny: Bibliogr. 22 poz., rys.

Twórcy

autor

Gwoździk M.

• Czestochowa University of Technology, Institute of Material Engineering, al. Armii Krajowej 19, 42-200 Czestochowa, Poland

autor

Bałaga Z.

• Czestochowa University of Technology, Institute of Material Engineering, al. Armii Krajowej 19, 42-200 Czestochowa, Poland

Bibliografia

• [1] Rinaldi M., Puglia D., Dominici F., Cherubini V., Torre L., Nanni F., Melt processing and mechanical property characterization of high-performance poly(ether ether ketone)-carbon nanotube composite, Polym. Int. 2017, 66, 1731-1736.
• [2] Strobel H.A., Calamari E.L., Beliveau A., Jain A., Rolle M.W., Fabrication and characterization of electrospun polycaprolactone and gelatin composite cuffs for tissue engineered blood vessels, J. Biomed. Mater. Res. Part B 2018:106B:817-826.
• [3] Shuo Zhao, Yiwei Zhang, Yuming Zhou, Kaibo Qiu, Chao Zhang, Jiasheng Fang, Xiaoli Sheng, Reactable polyelectrolyte-assisted preparation of flower-like Ag/AgCl/BiOCl composite with enhanced photocatalytic activity, Journal of Photochemistry and Photobiology A: Chemistry 2018, 350, 94-102.
• [4] Gwoździk M., Bałaga Z., Wróbel D., Nitkiewicz Z., Evaluation of wear degree of rotational instruments with diamond coat, Composites Theory and Practice 2017, 17(4), 216-220.
• [5] Zygoń P., Gwoździk M., Peszke J., Nitkiewicz Z., The effect of water acrylate dispersion on the properties of polymer-carbon nanotube composites, Archives of Metallurgy and Materials 2015, 60(4), 2716-2720.
• [6] Zygoń P., Gwoździk M., Peszke J., Nitkiewicz Z., Comparison of properties of polymer composite materials reinforced with carbon nanotubes, Archives of Metallurgy and Materials 2015, 60(1), 193-198.
• [7] Bałaga Z., Przybycin A., Wawrzyniak J., Gnatowski A., Examinations of the effect of montmorillonite on selected properties and structure of polybutylene terephthalate, Composites Theory and Practice 2017, 17(3), 175-179.
• [8] Xiangwen Ma, Peng Zhang, Yuanyuan Zhao, Ying Liu, Jian Li, Jin Yuan Zhou, Xiaojun Pan, Erqing Xie, Role of N doping on the electrochemical performances of ZnCo2O4 quantum dots/reduced graphene oxide composite nanosheets, Chemical Engineering Journal 2017, 327, 1000-1010.
• [9] Zygoń P., Peszke J., Gwoździk M., Nitkiewicz Z., Malik M., Characteristic of carbon nanotubes modified with cobalt, copper and bromine, Archives of Metallurgy and Materials 2014, 59(2), 675-679.
• [10] Szafarska M., Iwaszko J., Laser remelting treatment of plasma-sprayed Cr2O3 oxide coatings, Archives of Metallurgy and Materials 2012, 57(1), 215-221.
• [11] Dudek A., Microstructure and properties of the composites: hydroxyapatite with addition of zirconia phase, Journal of Engineering Materials and Technology, Transactions of the ASME, 2011, 133(2), 021006-1-021006-5.
• [12] Zygoń P., Gwoździk M., Nitkiewicz Z., Jagielska-Wiaderek K., Corrosion resistance of sinters Cu/CNT, Solid State Phenomena 2015, 227, 51-54.
• [13] Arabinda Meher, Debasis Chaira, Effect of graphite and SiC addition into Cu and SiC particle size effect on fabrication of Cu-graphite-SiC MMC by powder metallurgy, Trans Indian Inst Met 2017, 70(8), 2047-2057. DOI 10.1007/s12666-016-1026-1.
• [14] Gongjun Cui, Jian Ren, Zhangxiang Lu, The microstructure and wear characteristics of Cu-Fe matrix, Friction Material with Addition of SiC. Tribol Lett 2017, 65, 108. DOI 10.1007/s11249-017-0890-0.
• [15] Liu Meng, Bai Shuxin, Li Shun, Zhao Xun, Xiong Degan, Microstructure and thermal properties of SiCp/Cu composites with Mo coating on SiC particles, Journal of Wuhan University of Technology-Mater. Sci. 2017, 32, 5 103-1018. DOI 10.1007/s11595-017-1704-9.
• [16] Chmielewski M., Pietrzak K., Strojny-Nędza A., Jarząbek D., Nosewicz S., Investigations of interface properties in copper-silicon carbide composites, Arch. Metall. Mater. 2017, 62, 2B, 1315-1318, DOI: 10.1515/amm-2017-0200.
• [17] Prosviryakov A.S., SiC content effect on the properties of Cu-SiC composites produced by mechanical alloying, Journal of Alloys and Compounds 2015, 632, 707-710.
• [18] Jarząbek D.M., Milczarek M., Wojciechowski T., Dziekoński C., Chmielewski M., The effect of metal coatings on the interfacial bonding strength of ceramics to copper in sintered Cu-SiC composites, Ceramics International 2017, 43, 5283-5291.
• [19] Rabiee M., Mirzadeh H., Ataie A., Processing of Cu-Fe and Cu-Fe-SiC nanocomposites by mechanical alloying, Advanced Powder Technology 2017, 28, 1882-1887.
• [20] M. Ibrahim Abd El Aal, Effect of high-pressure torsion processing on the microstructure evolution and mechanical properties of consolidated micro size Cu and Cu-SiC powders, Advanced Powder Technology 2017, 28, 2135-2150.
• [21] Shabani M., Hossein Paydar M., Zamiri R., Goodarzi M., Mohsen Moshksar M., Microstructural and sliding wear behavior of SiC-particle reinforced copper matrix composites fabricated by sintering and sinter-forging processes, J. Mater. Restechnol. 2016, 5(1), 5-12.
• [22] Yanguang Zhou, Ming Hua, Mechanical behaviors of nanocrystalline Cu/SiC composites: An atomistic investigation. Computational Materials Science 2017, 129, 129-136.

Uwagi

Opracowanie rekordu w ramach umowy 509/P-DUN/2018 ze środków MNiSW przeznaczonych na działalność upowszechniającą naukę (2018).